Home » Public Forums » GMCnet » Oil Cooler Adaptor Gasket Profile (Adding to the knowledge Base)
Oil Cooler Adaptor Gasket Profile [message #267035] |
Wed, 03 December 2014 01:23 |
|
John Heslinga
Messages: 632 Registered: February 2011 Location: Edmonton, Alberta, Canada
Karma:
|
Senior Member |
|
|
Some time ago, there was a discussion about Oil Cooler Adaptor Gaskets. Because a factory original part was no longer made and is not available, there have been a number of field fixes, adaptations, and repair possibilities discussed.
A question was raised about what the factory part measurements are and if they were available in any way. Doing some work on a local coach this winter I removed the Oil Cooler Adaptor Gasket to repair a leak and found what I believe must be an original gasket with an original profile. After our discussions I was quite surprised at what I found.
I've measured the old gasket and present to you what I found. The old gasket had a Tee Profile with sharp edges and no evidence of extrusion or major distortion, therefore it represents pretty accurately, the shape that was originally installed. Fluctuations in actual measurements can be expected by the stresses of installation pressures.
This posting is simply sharing what I found and adding to the knowledge base.(as I promised)
Check out the following pictures.
Actual Photo
http://www.gmcmhphotos.com/photos/oil-filter-and-cooler/p56581-original-oil-cooler-adaptor-gasket.html
Measurements
http://www.gmcmhphotos.com/photos/oil-filter-and-cooler/p56584-gmc-oil-cooler-adaptor-gasket.html
http://www.gmcmhphotos.com/photos/oil-filter-and-cooler/p56602-factory-oil-cooler-adaptor-gasket-profile.html
Best Regards
John and Cathie Heslinga
1974 Canyonlands 260
455, Manny tranny and 1 ton, 3:70 LS,
Red Seal Journeyman, DTE, BEd. MEd.
Edmonton, Alberta
|
|
|
|
|
Oil Cooler Adaptor Gasket Profile
|
|
|
Re: [GMCnet] Oil Cooler Adaptor Gasket Profile
By: USAussie on Wed, 03 December 2014 04:30
|
|
|
Re: Oil Cooler Adaptor Gasket Profile
By: JohnL455 on Wed, 03 December 2014 08:42
|
|
|
Re: [GMCnet] Oil Cooler Adaptor Gasket Profile
|
|
|
Re: [GMCnet] Oil Cooler Adaptor Gasket Profile
By: USAussie on Wed, 03 December 2014 17:22
|
|
|
Re: Oil Cooler Adaptor Gasket Profile
|
|
|
Re: [GMCnet] Oil Cooler Adaptor Gasket Profile
By: USAussie on Sat, 06 December 2014 17:23
|
|
|
Re: Oil Cooler Adaptor Gasket Profile
By: USAussie on Mon, 08 December 2014 17:40
|
|
|
Re: Oil Cooler Adaptor Gasket Profile
By: Larry on Tue, 09 December 2014 09:21
|
|
|
Re: [GMCnet] Oil Cooler Adaptor Gasket Profile
By: powerjon on Tue, 09 December 2014 12:42
|
|
|
Re: [GMCnet] Oil Cooler Adaptor Gasket Profile
|
|
|
Re: [GMCnet] Oil Cooler Adaptor Gasket Profile
By: USAussie on Tue, 09 December 2014 15:57
|
|
|
Re: [GMCnet] Oil Cooler Adaptor Gasket Profile
By: Larry on Tue, 09 December 2014 16:12
|
|
|
Re: Oil Cooler Adaptor Gasket Profile
|
|
|
Re: Oil Cooler Adaptor Gasket Profile
|
|
|
Re: Oil Cooler Adaptor Gasket Profile
By: JohnL455 on Sat, 06 December 2014 18:31
|
|
|
Re: [GMCnet] Oil Cooler Adaptor Gasket Profile
By: USAussie on Sat, 06 December 2014 20:11
|
|
|
Re: [GMCnet] Oil Cooler Adaptor Gasket Profile
By: bdub on Sat, 06 December 2014 21:13
|
|
|
Re: [GMCnet] Oil Cooler Adaptor Gasket Profile
|
|
|
Re: [GMCnet] Oil Cooler Adaptor Gasket Profile
By: USAussie on Sun, 07 December 2014 08:07
|
|
|
Re: [GMCnet] Oil Cooler Adaptor Gasket Profile
|
|
|
Re: [GMCnet] Oil Cooler Adaptor Gasket Profile
By: USAussie on Sun, 07 December 2014 15:35
|
|
|
Re: Oil Cooler Adaptor Gasket Profile
|
Goto Forum:
Current Time: Tue Nov 05 12:59:34 CST 2024
Total time taken to generate the page: 0.00843 seconds
|