GMCforum: GMCnet » Mech. Engineer Q.

Home » Public Forums » GMCnet » Mech. Engineer Q.

Show: Today's Messages :: Polls :: Message Navigator

Mech. Engineer Q. [message #106472]

Mon, 22 November 2010 17:09

g.winger

Messages: 792
Registered: February 2008
Location: Warrenton,Missouri

Karma:

Senior Member

I want to lift a load from a single point. The load is 8000 pounds. Not going to lift it very high and no one will be under it. The load will be supported on two points about 6 feet apart. How large of a I or H beam will be needed??? Can a smaller beam be used with a triangle brace on top help??? I'm an electrician,,, not an ME. Thanks,,,,PL

Report message to a moderator

[Message index]

		Mech. Engineer Q. By: g.winger on Mon, 22 November 2010 17:09
		Re: [GMCnet] Mech. Engineer Q. By: Marsh Wilkes on Mon, 22 November 2010 19:11
		Re: Mech. Engineer Q. By: g.winger on Mon, 22 November 2010 19:32
		Re: Mech. Engineer Q. By: Harry on Mon, 22 November 2010 19:41
		Re: Mech. Engineer Q. By: Harry on Mon, 22 November 2010 19:59
		Re: [GMCnet] Mech. Engineer Q. By: jw mills on Mon, 22 November 2010 21:15
		Re: Mech. Engineer Q. By: g.winger on Mon, 22 November 2010 19:55
		Re: Mech. Engineer Q. By: Matt Colie on Mon, 22 November 2010 20:01
		Re: Mech. Engineer Q. By: g.winger on Mon, 22 November 2010 20:10
		Re: Mech. Engineer Q. By: Matt Colie on Tue, 23 November 2010 06:43
		Re: [GMCnet] Mech. Engineer Q. By: Ken Coit on Tue, 23 November 2010 07:02
		Re: [GMCnet] Mech. Engineer Q. By: USAussie on Tue, 23 November 2010 08:35
		Re: Mech. Engineer Q. By: fred v on Mon, 22 November 2010 22:18
		Re: [GMCnet] Mech. Engineer Q. By: Richard Denney on Mon, 22 November 2010 22:39
		Re: Mech. Engineer Q. By: g.winger on Tue, 23 November 2010 08:10
		Re: [GMCnet] Mech. Engineer Q. By: USAussie on Tue, 23 November 2010 08:40
		Re: [GMCnet] Mech. Engineer Q. By: Richard Denney on Tue, 23 November 2010 09:16
		Re: [GMCnet] Mech. Engineer Q. By: USAussie on Tue, 23 November 2010 09:56
		Re: Mech. Engineer Q. By: rwbmitiopt@comcast.net on Tue, 23 November 2010 10:31
		Re: [GMCnet] Mech. Engineer Q. By: James Hupy on Tue, 23 November 2010 11:26
		Re: [GMCnet] Mech. Engineer Q. By: Richard Denney on Tue, 23 November 2010 12:58
		Re: [GMCnet] Mech. Engineer Q. By: Ken Henderson on Tue, 23 November 2010 14:51
		Re: [GMCnet] Mech. Engineer Q. By: USAussie on Wed, 24 November 2010 21:35
		Re: [GMCnet] Mech. Engineer Q. By: fred v on Wed, 24 November 2010 22:18
		Re: [GMCnet] Mech. Engineer Q. By: Richard Denney on Wed, 24 November 2010 22:33
		Re: [GMCnet] Mech. Engineer Q. By: Ken Henderson on Wed, 24 November 2010 23:29
		Re: [GMCnet] Mech. Engineer Q. By: roy1 on Thu, 25 November 2010 15:52
		Re: [GMCnet] Mech. Engineer Q. By: k2gkk on Thu, 25 November 2010 18:58
		Re: [GMCnet] Mech. Engineer Q. By: mike miller on Tue, 23 November 2010 13:03
		Re: [GMCnet] Mech. Engineer Q. By: Richard Denney on Tue, 23 November 2010 13:11
		Re: Mech. Engineer Q. By: g.winger on Tue, 23 November 2010 12:40
		Re: Mech. Engineer Q. By: g.winger on Tue, 23 November 2010 13:11
		Re: Mech. Engineer Q. By: Craig Lechowicz on Tue, 23 November 2010 18:22

Previous Topic:	Re: [GMCnet] Wheel alignment specs
Next Topic:	Winterizing the GMC

Goto Forum:

-=] Back to Top [=-

Current Time: Thu Sep 26 17:10:58 CDT 2024

Total time taken to generate the page: 0.01053 seconds