[GMCnet] Adjusting the level [message #368813] |
Thu, 17 February 2022 17:42 |
Hanson Email
Messages: 110 Registered: March 2020
Karma: -1
|
Senior Member |
|
|
Can anyone point me to an article on how to adjust the level on the rear? It
is a 1975 Hughes, with quad bags.
Dean hanson
Fremont, Ca
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
|
|
|
[GMCnet] Re: Adjusting the level [message #368816 is a reply to message #368813] |
Thu, 17 February 2022 22:34 |
powwerjon
Messages: 849 Registered: March 2013
Karma: -2
|
Senior Member |
|
|
Dean,
Go to your X7525 maintenance manual, Pager 4.34 and see Fig 70 & 71. The
paragraph next Fig. 71 has the adjustment procedure. Fig. shows where and
why to take the measurements. You will need the torsion bar tool to adjust
the front ride height, see Chapter 3A-14 page for guidance. You will ;have
to measure the heights, take the coach for a short trip to settle the
suspension and check again, will take 3 or 4 times.
J.R. Wright
GMC Great Laker
GMCGL Tech Editor
GMC Eastern States
GMCMHI
TZE Zone Restorations
78 Buskirk Custom 29.5' Stretch
75 Avion (Under going Frame up Restoration)
On Thu, Feb 17, 2022 at 4:43 PM Hanson Email wrote:
> Can anyone point me to an article on how to adjust the level on the rear?
> It
> is a 1975 Hughes, with quad bags.
>
> Dean hanson
>
> Fremont, Ca
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
|
|
|
|
[GMCnet] Re: Adjusting the level [message #368821 is a reply to message #368818] |
Fri, 18 February 2022 08:43 |
Keith V
Messages: 2337 Registered: March 2008 Location: Mounds View,MN
Karma: 0
|
Senior Member |
|
|
Winter is almost over Matt, only 6 months left !
Don't forget that the rear height valves have both a time delay and hysterisis. this means you make a guestimated adjustment then you need to drive the coach or bounce it to settle the valves.
Keith Vasilakes
Mounds View MN
76 exRoyale
MicroLevel
________________________________
From: Matt Colie
Sent: Friday, February 18, 2022 7:51 AM
To: gmclist@list.gmcnet.org
Subject: [GMCnet] Re: Adjusting the level
Dean,
I guess John missed that you asked about the rear.
The page for that starts at 4-22 in the X7525 manual.
There is a slip joint where the arm attaches to the ride height control. It can be loosened and budged to get the height correct. This takes a lot
of fiddling. If the rubber inserts in the ends of the links are shot, they can be replaced with 3/8 fuel line.
I cheated and made turnbuckle like likes after I had repaired the ridged links.
Part of my winter work will be to install a Micro-Level system and new Viair 485 compressor.
Matt
--
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
Keith Vasilakes
Mounds View. MN
75 ex Royale GMC
ask me about MicroLevel
Cell, 763-732-3419
My427v8@hotmail.com
|
|
|
|