Home » Public Forums » GMCnet » Exhaust bang bang bang (going down steep grades)
| Exhaust bang bang bang [message #366771] |
Tue, 14 September 2021 11:18  |
boybach
Messages: 566
Registered: December 2020
Location: Vancouver Island
Karma: 4
|
Senior Member |
|
|
Exhaust backfires quite a bit if I put the trans in low going down a steep hill ..haven't had a carburetted vehicle in years and years so wondering if this is normal?
Recently drove the coach across Vancouver island, Port Renfrew - Mesachie Lake mountain road and then on to several steep unpaved roads down Riverbottom road in the Cowichan Valley. Coach ran perfectly, but backfiring was a little disconcerting.
Exhaust system is very new, stainless and extremely heavy duty BTW.
Larry
Larry - Victoria BC -
1977 ex-Palm Beach "Ol' Leaky" 40,000 miles, PO said everything working but forgot the word NOT. Atwood helium fridge, water heater & furnace. SS exhaust system, Onan, Iota Converter, R134A, New fuel lines & heat exchange hoses
|
|
|
|
| Re: Exhaust bang bang bang [message #366776 is a reply to message #366771] |
Tue, 14 September 2021 15:27  |
JohnL455
Messages: 4447
Registered: October 2006
Location: Woodstock, IL
Karma: 12
|
Senior Member |
|
|
Mine will “burble” during long engine braking, but I have my exact GM copy exhaust system installed so it is barely noticeable.
I suspect your idle mixture may be adding extra fuel causing this to be more pronounced. If you have 3” stainless this may exaggerate it. Correct mixture is balanced best idle just at the lean drop edge. “Emissions” setting would be 25 RPM lean drop per side to get 50 RPM lean drop.
John Lebetski
Woodstock, IL
77 Eleganza II
|
|
|
|
| [GMCnet] Re: Exhaust bang bang bang [message #366778 is a reply to message #366776] |
Tue, 14 September 2021 16:38 |
Keith V
Messages: 2337
Registered: March 2008
Location: Mounds View,MN
Karma: 0
|
Senior Member |
|
|
Mine has never done that with or without a carb with headers and 3" exhaust with a single rumbly flowmaster 80 in the back
Popping would seem to indicate unburned fuel in the exhaust. How is that happening?
________________________________
From: John R.Lebetski
Sent: Tuesday, September 14, 2021 3:27 PM
To: gmclist@list.gmcnet.org
Subject: [GMCnet] Re: Exhaust bang bang bang
Mine will “burble” during long engine braking, but I have my exact GM copy exhaust system installed so it is barely noticeable.
I suspect your idle mixture may be adding extra fuel causing this to be more pronounced. If you have 3” stainless this may exaggerate it. Correct
mixture is balanced best idle just at the lean drop edge. “Emissions” setting would be 25 RPM lean drop per side to get 50 RPM lean drop.
--
John Lebetski
Woodstock, IL
77 Eleganza II
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
Keith Vasilakes
Mounds View. MN
75 ex Royale GMC
ask me about MicroLevel
Cell, 763-732-3419
My427v8@hotmail.com
|
|
|
|
| Re: [GMCnet] Re: Exhaust bang bang bang [message #366779 is a reply to message #366778] |
Tue, 14 September 2021 17:57 |
Bill Van Vlack
Messages: 419
Registered: September 2015
Location: Guemes Island, Washington
Karma: 14
|
Senior Member |
|
|
With a couple EFI systems I have, you can turn on or off 'Deceleration Enleanment' and allow/disallow that burble. I used to turn off/on the ignition Dad's Dodge while coasting. BANG! I don't suppose that helped the muffler much.
Bill Van Vlack
'76 Royale; Guemes Island, Washington; Twin bed, full (DS) side bath, Brazilian Redwood counter and settee tops,455, 6KW generator; new owner a/o mid November 2015.
|
|
|
|
| Re: [GMCnet] Re: Exhaust bang bang bang [message #366781 is a reply to message #366778] |
Tue, 14 September 2021 19:11 |
boybach
Messages: 566
Registered: December 2020
Location: Vancouver Island
Karma: 4
|
Senior Member |
|
|
Keith V wrote on Tue, 14 September 2021 14:38
Popping would seem to indicate unburned fuel in the exhaust. How is that happening?
I don't know, that's why I asked. 
Larry
Larry - Victoria BC -
1977 ex-Palm Beach "Ol' Leaky" 40,000 miles, PO said everything working but forgot the word NOT. Atwood helium fridge, water heater & furnace. SS exhaust system, Onan, Iota Converter, R134A, New fuel lines & heat exchange hoses
|
|
|
|
| Re: Exhaust bang bang bang [message #366782 is a reply to message #366776] |
Tue, 14 September 2021 19:18 |
boybach
Messages: 566
Registered: December 2020
Location: Vancouver Island
Karma: 4
|
Senior Member |
|
|
JohnL455 wrote on Tue, 14 September 2021 13:27Mine will “burble” during long engine braking, but I have my exact GM copy exhaust system installed so it is barely noticeable.
I suspect your idle mixture may be adding extra fuel causing this to be more pronounced. If you have 3” stainless this may exaggerate it. Correct mixture is balanced best idle just at the lean drop edge. “Emissions” setting would be 25 RPM lean drop per side to get 50 RPM lean drop.
I have no way to check or test emissions, should I adjust the carburetor? How do I do that?
BTW, I have no idea what this statement means  "Correct mixture is balanced best idle just at the lean drop edge."
Larry
Larry - Victoria BC -
1977 ex-Palm Beach "Ol' Leaky" 40,000 miles, PO said everything working but forgot the word NOT. Atwood helium fridge, water heater & furnace. SS exhaust system, Onan, Iota Converter, R134A, New fuel lines & heat exchange hoses
|
|
|
|
| [GMCnet] Re: Exhaust bang bang bang [message #366783 is a reply to message #366779] |
Tue, 14 September 2021 19:21 |
James Hupy
Messages: 6806
Registered: May 2010
Karma: -62
|
Senior Member |
|
|
I did that same thing with my 1938 Oldsmobile. Blew out the muffler, and
broke a couple of valve springs. That ended that engine, and allowed me to
swap in a 303 Olds V-8. And Headers, and dual exhaust.
You have something hot enough inside the exhaust system to ignite a
combustible mixture of gasoline and oxygen. If you get rid of either one of
the three things I just mentioned, you will stop the banging. I would
concentrate upon the gasoline source if it were me. High engine rpm on
deceleration creates a very high vacuum with nearly closed throttle plates.
If they are open a bit too far, then air and fuel can enter the exhaust
system unburned, where it is ignited by hot exhaust components. Air can
also enter via worn throttle shaft bushings, even with throttle plates
closed. Time for a very close inspection of your carburetor. Just what I
would do.
Jim Hupy
Salem, Oregon
On Tue, Sep 14, 2021, 4:36 PM Bill Van Vlack
wrote:
> With a couple EFI systems I have, you can turn on or off 'Deceleration
> Enleanment' and allow/disallow that burble. I used to turn off/on the
> ignition
> Dad's Dodge while coasting. BANG! I don't suppose that helped the muffler
> much.
>
> --
> Bill Van Vlack
> '76 Royale; Guemes Island, Washington; Twin bed, full (DS) side bath,
> Brazilian Redwood counter and settee tops,455, 6KW generator; new owner a/o
> mid
> November 2015.
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
|
|
|
|
| Re: [GMCnet] Re: Exhaust bang bang bang [message #366786 is a reply to message #366783] |
Tue, 14 September 2021 21:17 |
boybach
Messages: 566
Registered: December 2020
Location: Vancouver Island
Karma: 4
|
Senior Member |
|
|
James Hupy wrote on Tue, 14 September 2021 17:21I did that same thing with my 1938 Oldsmobile. Blew out the muffler, and
broke a couple of valve springs. That ended that engine, and allowed me to
swap in a 303 Olds V-8. And Headers, and dual exhaust.
You have something hot enough inside the exhaust system to ignite a
combustible mixture of gasoline and oxygen. If you get rid of either one of
the three things I just mentioned, you will stop the banging. I would
concentrate upon the gasoline source if it were me. High engine rpm on
deceleration creates a very high vacuum with nearly closed throttle plates.
If they are open a bit too far, then air and fuel can enter the exhaust
system unburned, where it is ignited by hot exhaust components. Air can
also enter via worn throttle shaft bushings, even with throttle plates
closed. Time for a very close inspection of your carburetor. Just what I
would do.
Jim Hupy
Salem, Oregon
Thanks Jim, will investigate.
Larry
Larry - Victoria BC -
1977 ex-Palm Beach "Ol' Leaky" 40,000 miles, PO said everything working but forgot the word NOT. Atwood helium fridge, water heater & furnace. SS exhaust system, Onan, Iota Converter, R134A, New fuel lines & heat exchange hoses
|
|
|
|
| Re: Exhaust bang bang bang [message #366787 is a reply to message #366771] |
Wed, 15 September 2021 08:18 |
JohnL455
Messages: 4447
Registered: October 2006
Location: Woodstock, IL
Karma: 12
|
Senior Member |
|
|
Larry, idle mixture setting is a bit like tuning a guitar. Instead of a strobe tuner you use a tach needle. Since we have divided manifolds, each idle mixture screw feeds 4 cylinders discretely. They don’t blend like with an open plane racing manifold. With engine at full 195 temp you slowly adjust each mixture screw to get maximum idle speed. Each screw is only contributing to 4 cyls so it’s a bit of a back and forth process. If they were set wrong, you will have to go and adjust the idle speed screw to get it to 650 so you are in the idle circuit range. The screws only work in a limited range. Never bottom them with any force, and opening past about 3 turns does nothing further. Once you find the max RPM center spot about an 1/8 turn range, stop there. Then turn each screw in very slightly to where it would just want to start losing RPM but does not. You are then at the best lean edge of the best range. The GM lean drop setting would mean then turn one screw in watching tach to lose 25 RPM. Then turn in other screw for a 25 RPM drop. Then go back to the speed scree and add the 50 RPM you lost to get back to the 650. Technically this should be done with the air cleaner in place and the AutoThermAC pre heat active so carb idle air is in the 117F range, but you need to have a flexible carb mixture tool to do it correctly. If your carb throttle shaft is worn as Jim H suggests could be, you will be adjusting to a moving target making it less accurate.
John Lebetski
Woodstock, IL
77 Eleganza II
|
|
|
|
| Re: Exhaust bang bang bang [message #366788 is a reply to message #366782] |
Wed, 15 September 2021 08:49 |
 |
Matt Colie
Messages: 8547
Registered: March 2007
Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
boybach wrote on Tue, 14 September 2021 20:18JohnL455 wrote on Tue, 14 September 2021 13:27Mine will “burble” during long engine braking, but I have my exact GM copy exhaust system installed so it is barely noticeable.
I suspect your idle mixture may be adding extra fuel causing this to be more pronounced. If you have 3” stainless this may exaggerate it. Correct mixture is balanced best idle just at the lean drop edge. “Emissions” setting would be 25 RPM lean drop per side to get 50 RPM lean drop.
I have no way to check or test emissions, should I adjust the carburetor? How do I do that?
BTW, I have no idea what this statement means "Correct mixture is balanced best idle just at the lean drop edge."
Larry
While John's description is good, it does not make two points.
There are two idle screws in the carburetor base that must be balanced. I find the "around the corner" special screw driver and a mirror to be essential.
The lean drop edge is when the mixture is lean and if it goes any leaner at all, there is a precipitous drop in the idle speed. Without a tachometer and possibly a vacuum gauge, I don't know how one finds this. I did know one man that could, but he passed years back.
Matt
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
|
| [GMCnet] Re: Exhaust bang bang bang [message #366789 is a reply to message #366788] |
Wed, 15 September 2021 09:13 |
James Hupy
Messages: 6806
Registered: May 2010
Karma: -62
|
Senior Member |
|
|
Matt, it takes many years of setting "lean drop" to do it without a tach
and vacuum gage. (TacVac).
It requires a fully warmed- up engine, and 8 cylinders that are within
10% compression pressure of each other, really tuned to factory ignition
specs, good wires, plugs, rotor, cap, etc.
In other words, a textbook perfect engine. If anything has been
monkeyed with, like pcv, or vacuum advance, or air cleaner, etc. Then all
bets are off.
Then, the best a person can hope for is a low CO reading at the
tailpipe, and a somewhat steady state idle at 650 rpm + or - 100 rpm either
way.
I try to set idle speed so that no dieseling or "running on" happens
on a hot engine when the ignition is switched off with the transmission in
neutral, and the A/C system off as well.
Real world stuff applies here, most of these GMC'S are high mileage
with leaky headers, etc., etc. Makes idle tuning a challenge for sure.
Then you take in humidity, altitude, barometric pressure, etc.
Challenge for sure.
Jim Hupy
Salem, Oregon
On Wed, Sep 15, 2021, 6:49 AM Matt Colie wrote:
> boybach wrote on Tue, 14 September 2021 20:18
>> JohnL455 wrote on Tue, 14 September 2021 13:27
>>> Mine will “burble” during long engine braking, but I have my exact GM
> copy exhaust system installed so it is barely noticeable.
>>> I suspect your idle mixture may be adding extra fuel causing this to
> be more pronounced. If you have 3” stainless this may exaggerate it.
>>> Correct mixture is balanced best idle just at the lean drop edge.
> “Emissions” setting would be 25 RPM lean drop per side to get 50 RPM lean
>>> drop.
>>
>> I have no way to check or test emissions, should I adjust the
> carburetor? How do I do that?
>>
>> BTW, I have no idea what this statement means :d "Correct mixture is
> balanced best idle just at the lean drop edge."
>>
>>
>> Larry
>
> While John's description is good, it does not make two points.
>
> There are two idle screws in the carburetor base that must be balanced. I
> find the "around the corner" special screw driver and a mirror to be
> essential.
>
> The lean drop edge is when the mixture is lean and if it goes any leaner
> at all, there is a precipitous drop in the idle speed. Without a tachometer
> and possibly a vacuum gauge, I don't know how one finds this. I did know
> one man that could, but he passed years back.
>
> Matt
> --
> Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL,
> GMCES
> Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum
> Brakes with Applied Control Arms
> SE Michigan - Near DTW - Twixt A2 and Detroit
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
|
|
|
|
| Re: Exhaust bang bang bang [message #366791 is a reply to message #366771] |
Wed, 15 September 2021 11:20 |
boybach
Messages: 566
Registered: December 2020
Location: Vancouver Island
Karma: 4
|
Senior Member |
|
|
Well after reading the above I am both encouraged and discouraged! My coach isn't really very high mileage at all, but it is, like the others, old - so maybe things have decomposed. I don't know. In the last 10 or 12 years it was only driven on three trips until I started camping this year.
Trip one was from Bakersfield, California to BC then across Canada to Belleville Ontario. Long haul. Second was from Belleville Ontario to Scotch Creek BC. In the interim the coach spent 10 years indoors at a Belleville school bus fleet heated garage. Trip 3 was the delivery journey I made in March of this year, Scotch Creek to Victoria BC. Those trips added about 8500 miles and the odometer just turned 40,000 when I got the coach to the island.
Engine idles and runs smoothly, roars up hills with no problem and doesn't diesel on shutdown. If I were to describe the engine's behavior, I'd have to say she "runs like a top".
So ...do I start messing with things or just leave it be and put up with the popping exhaust on steep downgrades? 
Larry
Larry - Victoria BC -
1977 ex-Palm Beach "Ol' Leaky" 40,000 miles, PO said everything working but forgot the word NOT. Atwood helium fridge, water heater & furnace. SS exhaust system, Onan, Iota Converter, R134A, New fuel lines & heat exchange hoses
|
|
|
|
| [GMCnet] Re: Exhaust bang bang bang [message #366793 is a reply to message #366791] |
Wed, 15 September 2021 11:32 |
sgltrac
Messages: 2797
Registered: April 2011
Karma: 1
|
Senior Member |
|
|
Have you tried switching fuels?
Sully
Bellevue wa
On Wed, Sep 15, 2021 at 9:20 AM wrote:
> Well after reading the above I am both encouraged and discouraged! My
> coach isn't really very high mileage at all, but it is, like the others,
> old -
> so maybe things have decomposed. I don't know. In the last 10 or 12 years
> it was only driven on three trips until I started camping this year.
>
> Trip one was from Bakersfield, California to BC then across Canada to
> Belleville Ontario. Long haul. Second was from Belleville Ontario to Scotch
> Creek BC. In the interim the coach spent 10 years indoors at a Belleville
> school bus fleet heated garage. Trip 3 was the delivery journey I made in
> March of this year, Scotch Creek to Victoria BC. Those trips added about
> 8500 miles and the odometer just turned 40,000 when I got the coach to the
> island.
>
> Engine idles and runs smoothly, roars up hills with no problem and doesn't
> diesel on shutdown. If I were to describe the engine's behavior, I'd have
> to say she "runs like a top".
>
> So ...do I start messing with things or just leave it be and put up with
> the popping exhaust on steep downgrades? :?
>
> Larry
> --
> Larry - Victoria BC -
>
> 1977 Palm Beach 40,000 miles, PO said everything working but forgot the
> word NOT. New Atwood fridge, water heater & furnace. New SS exhaust system,
> 6000w Onan, Iota Converter, R134A A/C, New fuel lines & heat exchange hoses
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
Sully
77 Royale basket case.
Future motorhome land speed record holder(bucket list)
Seattle, Wa.
|
|
|
|
| Re: [GMCnet] Re: Exhaust bang bang bang [message #366795 is a reply to message #366793] |
Wed, 15 September 2021 12:35 |
boybach
Messages: 566
Registered: December 2020
Location: Vancouver Island
Karma: 4
|
Senior Member |
|
|
sgltrac wrote on Wed, 15 September 2021 09:32Have you tried switching fuels?
Sully
Bellevue wa
No, I just run regular ...are you suggesting running higher octane? I know higher octane has less oomph than regular but I don't ping or diesel ATM ...there isn't much difference in brands up here AFAIK, so hate to throw another tankful or two in her at 20ȼ a litre (about 50ȼ a US gallon) for "premium" 
Larry
Larry - Victoria BC -
1977 ex-Palm Beach "Ol' Leaky" 40,000 miles, PO said everything working but forgot the word NOT. Atwood helium fridge, water heater & furnace. SS exhaust system, Onan, Iota Converter, R134A, New fuel lines & heat exchange hoses
|
|
|
|
| Re: [GMCnet] Re: Exhaust bang bang bang [message #366796 is a reply to message #366795] |
Wed, 15 September 2021 15:17 |
mghamms
Messages: 466
Registered: March 2016
Location: Ware, Massachusetts
Karma: 2
|
Senior Member |
|
|
Try filling from half full with premium gas.
I usually alternate premium to regular when filling from about half full.
Seems to run better that regular only.
1977 Kingsley 455 as stock as it gets except lots of Ragusa parts
|
|
|
|
| Re: Exhaust bang bang bang [message #366797 is a reply to message #366771] |
Wed, 15 September 2021 15:56 |
JohnL455
Messages: 4447
Registered: October 2006
Location: Woodstock, IL
Karma: 12
|
Senior Member |
|
|
Matt I think I went into detail to state to use a tach and how and why both mixture screws must both be adjusted. If you have a good ear (retired audio eng) you can do it by pitch as that correlates to a finite RPM. When trimming for the absolute edge, eyes and ears are best together.
Larry. Start by just checking base idle speed. A 50 RPM difference could minimize your issue. That’s the throttle stop screw on accelerator linkage drivers side of Qjet.
John Lebetski
Woodstock, IL
77 Eleganza II
[Updated on: Wed, 15 September 2021 15:57] Report message to a moderator |
|
|
|
| [GMCnet] Re: Exhaust bang bang bang [message #366799 is a reply to message #366795] |
Wed, 15 September 2021 16:08 |
sgltrac
Messages: 2797
Registered: April 2011
Karma: 1
|
Senior Member |
|
|
I mean non ethanol vs ethanol.
Sully
Bellevue wa
On Wed, Sep 15, 2021 at 10:35 AM wrote:
> sgltrac wrote on Wed, 15 September 2021 09:32
>> Have you tried switching fuels?
>>
>> Sully
>> Bellevue wa
>
> No, I just run regular ...are you suggesting running higher octane? I know
> higher octane has less oomph than regular but I don't ping or diesel ATM
> ...there isn't much difference in brands up here AFAIK, so hate to throw
> another tankful or two in her at 20ȼ a litre (about 50ȼ a US gallon) for
> "premium" 8o
>
> Larry
> --
> Larry - Victoria BC -
>
> 1977 Palm Beach 40,000 miles, PO said everything working but forgot the
> word NOT. New Atwood fridge, water heater & furnace. New SS exhaust system,
> 6000w Onan, Iota Converter, R134A A/C, New fuel lines & heat exchange hoses
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
Sully
77 Royale basket case.
Future motorhome land speed record holder(bucket list)
Seattle, Wa.
|
|
|
|
| Re: Exhaust bang bang bang [message #366801 is a reply to message #366797] |
Wed, 15 September 2021 17:03 |
boybach
Messages: 566
Registered: December 2020
Location: Vancouver Island
Karma: 4
|
Senior Member |
|
|
JohnL455 wrote on Wed, 15 September 2021 13:56Matt I think I went into detail to state to use a tach and how and why both mixture screws must both be adjusted. If you have a good ear (retired audio eng) you can do it by pitch as that correlates to a finite RPM. When trimming for the absolute edge, eyes and ears are best together.
Larry. Start by just checking base idle speed. A 50 RPM difference could minimize your issue. That’s the throttle stop screw on accelerator linkage drivers side of Qjet.
Thanks John, I hear you 
Larry
Larry - Victoria BC -
1977 ex-Palm Beach "Ol' Leaky" 40,000 miles, PO said everything working but forgot the word NOT. Atwood helium fridge, water heater & furnace. SS exhaust system, Onan, Iota Converter, R134A, New fuel lines & heat exchange hoses
|
|
|
|
| Re: [GMCnet] Re: Exhaust bang bang bang [message #366802 is a reply to message #366799] |
Wed, 15 September 2021 17:07 |
boybach
Messages: 566
Registered: December 2020
Location: Vancouver Island
Karma: 4
|
Senior Member |
|
|
sgltrac wrote on Wed, 15 September 2021 14:08I mean non ethanol vs ethanol.
Sully
Bellevue wa
We don't have much of a choice in that dept., I think only the top Chevron grade is ethanol free and that's some expensive stuff.
Thanks for the tip though
Larry
Larry - Victoria BC -
1977 ex-Palm Beach "Ol' Leaky" 40,000 miles, PO said everything working but forgot the word NOT. Atwood helium fridge, water heater & furnace. SS exhaust system, Onan, Iota Converter, R134A, New fuel lines & heat exchange hoses
|
|
|
|
| Re: Exhaust bang bang bang [message #366803 is a reply to message #366771] |
Wed, 15 September 2021 17:17 |
boybach
Messages: 566
Registered: December 2020
Location: Vancouver Island
Karma: 4
|
Senior Member |
|
|
So I suppose my first step would be to find an old tach/tune-up kit/tool ...I guess I'll keep my eyes open at junk shops, garage sales and fleamarkets?
Larry
Larry - Victoria BC -
1977 ex-Palm Beach "Ol' Leaky" 40,000 miles, PO said everything working but forgot the word NOT. Atwood helium fridge, water heater & furnace. SS exhaust system, Onan, Iota Converter, R134A, New fuel lines & heat exchange hoses
|
|
|
|
Goto Forum:
Current Time: Tue Jul 02 02:32:33 CDT 2024
Total time taken to generate the page: 0.06739 seconds
|
GMCforum
Search
Help
Register
Login
Home
