GMCforum: GMCnet » Electra-Magic toilet removal

Home » Public Forums » GMCnet » Electra-Magic toilet removal - slides won't budge

Show: Today's Messages :: Polls :: Message Navigator

Electra-Magic toilet removal - slides won't budge [message #356196]

Sun, 28 June 2020 16:38

westlanddave78

Messages: 27
Registered: March 2006
Location: Westland, MI

Karma: 0

Junior Member

Hi all,

Well it's time to change the dump valve out on the old Electra-Magic toilet but I can't get the toilet off its mounts. I took off the trim around the bottom and tried to pull the slides forward with a coat hanger as it says in the instructions, but no luck. I tried pulling on the slides with a pair of gas pliers but that didn't budge them either. Right now I'm letting a good spray of B'laster soak in.

Any other hints or tips I should try?

Thanks,
Dave
'75 Palm Beach

Dave P.
Westland, MI
75 Palm Beach

Report message to a moderator

Re: [GMCnet] Electra-Magic toilet removal - slides won't budge [message #356197 is a reply to message #356196]

Sun, 28 June 2020 17:00

James Hupy

Messages: 6806
Registered: May 2010

Karma: -62

Senior Member

Sawzall and a new toilet.
Jim Hupy
Salem, Oregon

On Sun, Jun 28, 2020, 2:39 PM David Pilon via Gmclist <
gmclist@list.gmcnet.org> wrote:

> Hi all,
>
> Well it's time to change the dump valve out on the old Electra-Magic
> toilet but I can't get the toilet off its mounts. I took off the trim
> around the
> bottom and tried to pull the slides forward with a coat hanger as it says
> in the instructions, but no luck. I tried pulling on the slides with a pair
> of gas pliers but that didn't budge them either. Right now I'm letting a
> good spray of B'laster soak in.
>
> Any other hints or tips I should try?
>
> Thanks,
> Dave
> '75 Palm Beach
> --
> Dave P.
> Westland, MI
> 75 Palm Beach
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org

Report message to a moderator

Re: Electra-Magic toilet removal - slides won't budge [message #356205 is a reply to message #356196]

Sun, 28 June 2020 22:57

Matt Colie

Messages: 8547
Registered: March 2007
Location: S.E. Michigan

Karma: 7

Senior Member

westlanddave78 wrote on Sun, 28 June 2020 17:38

Hi all,

Well it's time to change the dump valve out on the old Electra-Magic toilet but I can't get the toilet off its mounts. I took off the trim around the bottom and tried to pull the slides forward with a coat hanger as it says in the instructions, but no luck. I tried pulling on the slides with a pair of gas pliers but that didn't budge them either. Right now I'm letting a good spray of B'laster soak in.

Any other hints or tips I should try?

Thanks,
Dave
'75 Palm Beach

Dave,

You need a friend that has a slide hammer with a seal hook.
I'm down in New Boston, Sibley and 275.
I know where the slide hammer is, but I haven't seen the seal hook in a while.

Matt

Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit

Report message to a moderator

Re: Electra-Magic toilet removal - slides won't budge [message #356213 is a reply to message #356196]

Mon, 29 June 2020 07:47

westlanddave78

Messages: 27
Registered: March 2006
Location: Westland, MI

Karma: 0

Junior Member

Thanks Matt. I was able to remove the toilet.

For anyone else who might stumble onto this post later, the Electra-Magic underwent a design change between 1975 and 1976. The pre-1976 model had a stainless steel dump valve, for which replacement parts are no longer available. This model also bolted directly to the closet bolts on the toilet flange. The 1976 model changed to a plastic dump valve, which still is available as both a complete assembly and a kit of renewal parts (rubber gaskets). The 1976 model also had sliding mounting brackets that engage the closet bolts. The nuts on the closet bolts need to be set to a particular height as described in the manual. The brackets slide backward to engage and forward to disengage.

Dave P.
Westland, MI
75 Palm Beach

Report message to a moderator

Re: Electra-Magic toilet removal - slides won't budge [message #356270 is a reply to message #356205]

Tue, 30 June 2020 13:51

rgogan

Messages: 82
Registered: February 2004
Location: Milwaukee, WI

Karma: 0

Member

I installed a replacement Electro-Magic on my 1976 Elaganza and had min trouble getting the slides out both when I removed the original one with the metal valve and subsequently when I removed the newer one with the plastic valve. I remember it did take some force on the coat hanger hook to break the slides loose. Used the replacement unit for several years but my wife was never on board with a recirculating toilet. Installed a conventional toilet that works fine but the minimally used ElectroMagic is still sitting in my garage. If anyone is interested in it, I can ship it out for the cost of shipping and a minimal handling fee.

Report message to a moderator

Previous Topic:	GMC life on hold
Next Topic:	[GMCnet] More battery discussion

Goto Forum:

-=] Back to Top [=-

Current Time: Sat Sep 21 08:48:37 CDT 2024

Total time taken to generate the page: 0.01593 seconds