Home » Public Forums » GMCnet » Going after a new (to me) GMC
Going after a new (to me) GMC [message #356106] |
Fri, 26 June 2020 08:51 |
Greg C.
Messages: 224 Registered: October 2019 Location: Knoxville, TN
Karma: 0
|
Senior Member |
|
|
Good morning. Tomorrow I start a journey most of you have already started, many more than once. I'm driving some 900 miles to inspect and hopefully purchase a 1977 Royale.
I've put a deposit down to hold it until I can get there. I'm taking tools, engine liquids, Bdub Buyers checklist, vacuum gauge and reading sheet, AAA RV Premier towing insurance, a co-driver, copy of the Black List,
and anything else I can think of between now and in the morning. I must admit I am very nervous about driving it 900 miles for its initial voyage under my command. I guess I'm just reaching out here for some
assurances that it might possibly be alright! PO runs it often, last drove it 300 miles in October with no issues.
So wish me luck, and watch out for cries of help!
Thank you.
Greg Crawford
KM4ZCR
Knoxville, TN
"Ruby Sue"
1977 Royale
Rear Bath
403 Engine
American Eagle Wheels
Early Version Alex Sirum Quad bags
|
|
|
Re: [GMCnet] Going after a new (to me) GMC [message #356109 is a reply to message #356106] |
Fri, 26 June 2020 09:05 |
Olly Schmidt
Messages: 1265 Registered: February 2014 Location: Germany and Scottsville, ...
Karma: 8
|
Senior Member |
|
|
On 26.06.20 15:51, Greg Crawford via Gmclist wrote:
> I must admit I am very nervous about driving it 900 miles for its
> initial voyage under my command.
My maiden voyage with the Eleganza was from San Diego to Charlottesville
- without a hitch.
Enjoy the drive, stop every hour or so, check fluids and air, and you'll
be good!
--
Best regards
Olly Schmidt
PGP KeyID: 0x4196BF22
'76a 26' Eleganza II - Virginia, US
'73 23' Sequoia - Schleswig-Holstein, Germany
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Best regards
Olly Schmidt
PGP Key ID: 0x18a9 3a1f 4196 bf22
'76a Eleganza II, VA
'73 Sequoia, SH, Germany
|
|
|
Re: Going after a new (to me) GMC [message #356110 is a reply to message #356106] |
Fri, 26 June 2020 09:44 |
Carl S.
Messages: 4186 Registered: January 2009 Location: Tucson, AZ.
Karma: 13
|
Senior Member |
|
|
If the coach has been in regular use, you shouldn't have any problems. One thing you might want to pick up a couple of fuel filters. If the coach has the stock carburetor, it might be a good idea to change out that filter and check for any additional in line filters that may have been added.
Just keep an eye on the fluids and take it easy. also check the wheel bearing temps when you stop. They shouldn't be TOO hot to the touch at the center of the wheels.
Carl Stouffer
'75 ex Palm Beach
Tucson, AZ.
Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive, Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American Eagles, Solar battery charging. GMCSJ and GMCMI member
|
|
|
Re: [GMCnet] Going after a new (to me) GMC [message #356111 is a reply to message #356106] |
Fri, 26 June 2020 09:41 |
Ken Henderson
Messages: 8726 Registered: March 2004 Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
Greg,
You left out important information: Where it is located and your route
home. With that information, some of us might be ready to help if needed
(hopefully not), or offer RON space so you don't have to drive straight
through.
Ken H.
Americus, GA
'76 X-Birchaven w/Cad500/Howell EFI & EBL,
Manny Brakes & 1-Ton, Troy-Bilt APU, etc., etc., etc.
www.gmcwipersetc.com
On Fri, Jun 26, 2020 at 9:52 AM Greg Crawford via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Good morning. Tomorrow I start a journey most of you have already started,
> many more than once. I'm driving some 900 miles to inspect and hopefully
> purchase a 1977 Royale.
>
> I've put a deposit down to hold it until I can get there. I'm taking
> tools, engine liquids, Bdub Buyers checklist, vacuum gauge and reading
> sheet,
> AAA RV Premier towing insurance, a co-driver, copy of the Black List,
>
> and anything else I can think of between now and in the morning. I must
> admit I am very nervous about driving it 900 miles for its initial voyage
> under my command. I guess I'm just reaching out here for some
>
> assurances that it might possibly be alright! PO runs it often, last drove
> it 300 miles in October with no issues.
>
> So wish me luck, and watch out for cries of help!
>
> Thank you.
> --
> Greg Crawford
> Knoxville, TN
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
Re: [GMCnet] Going after a new (to me) GMC [message #356113 is a reply to message #356111] |
Fri, 26 June 2020 10:43 |
Greg C.
Messages: 224 Registered: October 2019 Location: Knoxville, TN
Karma: 0
|
Senior Member |
|
|
Oops. Driving from Knoxville, Tn to Cleburne TX. Returning via I-20 to I-59
to I-75. Hope to leave early afternoon Monday for the return trip.
On Fri, Jun 26, 2020, 10:41 AM Ken Henderson wrote:
> Greg,
>
> You left out important information: Where it is located and your route
> home. With that information, some of us might be ready to help if needed
> (hopefully not), or offer RON space so you don't have to drive straight
> through.
>
> Ken H.
> Americus, GA
> '76 X-Birchaven w/Cad500/Howell EFI & EBL,
> Manny Brakes & 1-Ton, Troy-Bilt APU, etc., etc., etc.
> www.gmcwipersetc.com
>
>
> On Fri, Jun 26, 2020 at 9:52 AM Greg Crawford via Gmclist gmclist@list.gmcnet.org> wrote:
>
>> Good morning. Tomorrow I start a journey most of you have already
>> started, many more than once. I'm driving some 900 miles to inspect and
>> hopefully
>> purchase a 1977 Royale.
>>
>> I've put a deposit down to hold it until I can get there. I'm taking
>> tools, engine liquids, Bdub Buyers checklist, vacuum gauge and reading
>> sheet,
>> AAA RV Premier towing insurance, a co-driver, copy of the Black List,
>>
>> and anything else I can think of between now and in the morning. I must
>> admit I am very nervous about driving it 900 miles for its initial voyage
>> under my command. I guess I'm just reaching out here for some
>>
>> assurances that it might possibly be alright! PO runs it often, last
>> drove it 300 miles in October with no issues.
>>
>> So wish me luck, and watch out for cries of help!
>>
>> Thank you.
>> --
>> Greg Crawford
>> Knoxville, TN
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Greg Crawford
KM4ZCR
Knoxville, TN
"Ruby Sue"
1977 Royale
Rear Bath
403 Engine
American Eagle Wheels
Early Version Alex Sirum Quad bags
|
|
|
|
Re: Going after a new (to me) GMC [message #356116 is a reply to message #356115] |
Fri, 26 June 2020 11:19 |
tphipps
Messages: 3005 Registered: August 2004 Location: Spanish Fort, AL
Karma: 9
|
Senior Member |
|
|
You are lucky living near Chuck Boyd. He is an excellent GMC mechanic, Posts often on the forum.
Tell Chuck Tom said, "Hi."
Tom
2012 Phoenix Cruiser model 2552
KA4CSG
|
|
|
Re: Going after a new (to me) GMC [message #356125 is a reply to message #356106] |
Fri, 26 June 2020 12:03 |
6cuda6
Messages: 975 Registered: June 2019
Karma: -6
|
Senior Member |
|
|
Sounds like your on the right path.....we did the same last year....bring tools, stop get to get fluids etc [which you have mostly covered]. Take it easy for a while and get use to the noises, the ride, the BRAKES and so forth. Don't forget to check the basic before you roll out with the coach, like a jack, tire iron, spare with air and the rest of the usual of course.
I gave myself lots of room between cars, watched the gauges religiously stopped regularly to check tires temps/wheel temps [even by hand is fine] and took our time, and enjoyed the scenery from the big glass
Have fun and think of it as an adventure....
Rich Mondor,
Brockville, ON
77 Hughes 2600
|
|
|
Re: Going after a new (to me) GMC [message #356132 is a reply to message #356125] |
Fri, 26 June 2020 13:10 |
Ken Burton
Messages: 10030 Registered: January 2004 Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
I have moved quite a few unknown to me "new purchase" coaches cross country for people in the past. I have never had a major failure or even a flat tire. I did it because I had time and enjoy the drive. I have never figured out why people in California buy coaches in the Midwest or east, and people in the east buy coaches from the west coast.
It is good insurance take some basic tools (wrenches, pliers, screwdrivers, etc) Then you will never need to use them.
I have had small stuff break. It is never anything you expect.
Things like a leaking master cylinder. That turned out to be the cover seal.
Broken gas line between the frame and the engine. 6" or 8" piece of 3/8" hose is all it needed. Plus one screw driver for the clamps.
One pair of windshield wiper blades. In stock at NAPA
One heater fan - in stock at AutoZone.
One leaking heater hose at the manifold. I trimed it back and reinstalled it. Put a razor knife and duct tape in your tool kit.
I think the worse one was a coach with rusty gas tanks. It had two inline filters and every day I replace on or the other when it starved out for gas. If you stop and get them, you will never need them on your way home.
Enjoy your trip, Take some extra time and ride a few secondary highways just for the scenery.
Take a current Black List. Call locally if you have problem or anyone if you just have questions.
Walmart is always a good place for an overnight stay except in the People's Republic of California, Galveston, Grand Junction and a few widely spaced places. None of which should you be going past.
Have a great trip.
Ken B.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
|
|
Re: [GMCnet] Going after a new (to me) GMC [message #356140 is a reply to message #356106] |
Fri, 26 June 2020 14:29 |
bdub
Messages: 1578 Registered: February 2004 Location: Central Texas
Karma: 5
|
Senior Member |
|
|
You should have no trouble with that '77 Center Kitchen, Rear Bath, Royale.
It is ready to tow your small car to Knoxville.
Good luck! Keep us in the loop. And don't forget to update its pedigree at
www.gmmhregistry.com
bdub
-----Original Message-----
From: Gmclist On Behalf Of Greg Crawford via Gmclist
Sent: Friday, June 26, 2020 8:52 AM
Subject: [GMCnet] Going after a new (to me) GMC
Good morning. Tomorrow I start a journey most of you have already started,
many more than once. I'm driving some 900 miles to inspect and hopefully
purchase a 1977 Royale.
I've put a deposit down to hold it until I can get there. I'm taking tools,
engine liquids, Bdub Buyers checklist, vacuum gauge and reading sheet,
AAA RV Premier towing insurance, a co-driver, copy of the Black List,
and anything else I can think of between now and in the morning. I must
admit I am very nervous about driving it 900 miles for its initial voyage
under my command. I guess I'm just reaching out here for some
assurances that it might possibly be alright! PO runs it often, last drove
it 300 miles in October with no issues.
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
bdub
'76 Palm Beach/Central Texas
www.bdub.net
www.gmcmhphotos.com
www.gmcmotorhomemarketplace.com
www.gmcmhregistry.com
www.facebook.com/groups/classicgmcmotorhomes
www.facebook.com/groups/gmcmm
|
|
|
Re: Going after a new (to me) GMC [message #356381 is a reply to message #356106] |
Fri, 03 July 2020 13:01 |
Greg C.
Messages: 224 Registered: October 2019 Location: Knoxville, TN
Karma: 0
|
Senior Member |
|
|
Well, it was a long trip. Bought the coach on Monday, June 29. Tires which had been described as good tread, a little old, were age cracked severely, so new tires were obtained after about four hours. Drove it uneventfully to Corsicana, TX, about 90 miles, to a campground for the night.
The next day was horrible. The coach started missing badly as if starving for fuel. It would run a short time, and then miss for for five or ten miles limiting the speed to about 40. Then clear up for five or ten and repeat the process. I stopped at an autoparts store and obtained a new carburetor fuel filter. But after stopping, the coach would not start. Thought it was the battery until I checked the voltage. After talking with Chuck Boyd, I crawled under the coach and smacked the starter with a hammer a few times, and then she started. After I bought another starter, the old one never failed to start again.
Brakes weren't real good to start with, but then I stupidly left the parking brake on after the starter issue and didn't realize it. Evidently the warning light does not work. So after a few miles, when I went to stop at a traffic light, I kind of slid halfway through it with the brake pressure warning light coming on. You should have seen the look at that girl's face who had just pulled out...
Stopped again to get a master cylinder. Coach still missing so badly there was no way I could get it on the interstate. Dumped a few bottles of Heet in it and filled it up. Seemed to help some. Discovered the brake was on. Took it off and let everything cool back down. I had been checking tire/hub temps with an infrared gun. Hubs were typically 98 to 104 in 98 degree ambient temperature. But after leaving the brake on, one axle was 148. So it definitely got hot. After an hour cool down, I had brakes again.
By then, it was getting later in the day. We had bypassed DFW, Longview, Tyler, and Shreveport on some backroads so small there wasn't a divider line painted on it. And rough. This probably exacerbated whatever sediment/water was floating around in the tanks. I discovered that by reducing throttle the fuel pump could catch up and it would straighten out. Of course this meant I was doing about 30 over hills.
Pulled into a campground in MS after 14 long, hot hours. I was thoroughly stressed, depressed, and really second guessing my choices.
The next day, third on the road, everything seemed to click right along. Got on the interstate and rolled at 60-65 for an hour and a half before the missing started. It missed a little, and then straightened up. We drove for 453 miles, stopping about three times. It would miss occasionally, mostly when going uphill and I needed to add throttle to maintain a steady speed. Pulled the hill north of Chattanooga on I-75 without missing because I would feather the throttle whenever I felt it was running out of fuel in the bowl. So we topped the hill at 35 mph. Tried to run right around 60 mph on the flats.
Anyway, I was so glad to make it home safely. Shout out to Steve Magown of the Black list who offered me use of his shop. If we hadn't already passed him up I would have taken his offer gladly on that rough day.
So that's my story, Ruby Sue (as my cousin-in-law has named her, after the red haired girl in Christmas Vacation) is sitting in the driveway. First order of business is to fix the leaking exhaust manifold, the leaking black water valve, and go through the brakes.
Thanks to Chuck Boyd for taking my several calls and offering advice, and the gentleman who texted me with numbers for the closest Black list members. Billy Massey, I have registered the coach on the Registry Site per your request.
Thanks to everyone for their help and encouragement.
Greg Crawford
KM4ZCR
Knoxville, TN
"Ruby Sue"
1977 Royale
Rear Bath
403 Engine
American Eagle Wheels
Early Version Alex Sirum Quad bags
|
|
|
Re: Going after a new (to me) GMC [message #356385 is a reply to message #356106] |
Fri, 03 July 2020 16:38 |
6cuda6
Messages: 975 Registered: June 2019
Karma: -6
|
Senior Member |
|
|
Sounds like a real adventure and a story to share in the future. One thing is for sure, every little thing that just happened along the route home will never happen again as you will have every piece and tool needed to fix it next time.....lol.
In case your still on the fence about your choice to buy this coach just think if the coach had been 20 years newer and did the same thing you would be crap out of luck to even attempt to fix it on the road.....they maybe on the older side but sometimes the old simple technology can be a bonus.
Glad you made it with all wheels on the ground rolling!
Rich Mondor,
Brockville, ON
77 Hughes 2600
|
|
|
Re: Going after a new (to me) GMC [message #356386 is a reply to message #356106] |
Fri, 03 July 2020 18:35 |
|
Matt Colie
Messages: 8547 Registered: March 2007 Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
Greg,
I have already said welcome, and you already understand the power of the support of this community, so most of my welcome can be by-passed at this time.
There is also a lot that I can forget about because you have a local mentor that is truly first string, dream team and all. Just don't expect him to run.
But, I (we) would all like you to fill in your sigfile more completely. This is really to help us be more helpful to you. So, go back to the sigfile place and fill in 77 Royale and anything special about it that might matter. This is such an amazing community of supportive and helping people that, if you ever have need, grab a handle and hold on tight.....
The only other community that I know of that is like this that of the watermen that are my world. Because of this, I like to welcome new owners much as you should be welcomed there. So,
May the Good Lord bless this coach and all those that set forth within her.
Welcome Greg.
Matt
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
Re: Going after a new (to me) GMC [message #356389 is a reply to message #356386] |
Fri, 03 July 2020 20:48 |
Carl S.
Messages: 4186 Registered: January 2009 Location: Tucson, AZ.
Karma: 13
|
Senior Member |
|
|
Greg,
It sounds like you were experiencing the very common fuel starvation that a lot of us have been battling in the Summer months. I fought it for years. There are several ways to (maybe) fix this. One is with in tank electric pumps. I went another route, tried everything and finally succeeded by moving the fuel lines, filters, and electric pump to the outside of the frame. Even the return directly from the fuel filter housing didn't do the trick, but moving the fuel lines etc did.
http://www.gmcmhphotos.com/photos/g6819-carburetor-fuel-return-2fvapor-lock-remedy.html
Carl Stouffer
'75 ex Palm Beach
Tucson, AZ.
Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive, Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American Eagles, Solar battery charging. GMCSJ and GMCMI member
|
|
|
Re: [GMCnet] Going after a new (to me) GMC [message #356390 is a reply to message #356389] |
Fri, 03 July 2020 21:22 |
|
ljdavick
Messages: 3548 Registered: March 2007 Location: Fremont, CA
Karma: -3
|
Senior Member |
|
|
I bought our coach sight unseen in Ohio. I live in California. Had it taken to Tom Hampton’s place where a checkbook can do some good and then flew out with a couple of buddies to driver it home.
Fill-ups were like the Exxon Valdez with gas’s spilling everywhere.
Finally after many years all the fuel lines have been replaced, fuel injection in place and it purrs better than Ransom Olds could have done.
So many happy memories Totally worth it.
Larry Davick.
1976 Palm Beach
Fremont Ca
> On Jul 3, 2020, at 6:49 PM, Carl Stouffer via Gmclist wrote:
>
> Greg,
>
> It sounds like you were experiencing the very common fuel starvation that a lot of us have been battling in the Summer months. I fought it for years.
> There are several ways to (maybe) fix this. One is with in tank electric pumps. I went another route, tried everything and finally succeeded by
> moving the fuel lines, filters, and electric pump to the outside of the frame. Even the return directly from the fuel filter housing didn't do the
> trick, but moving the fuel lines etc did.
>
> http://www.gmcmhphotos.com/photos/g6819-carburetor-fuel-return-2fvapor-lock-remedy.html
> --
> Carl Stouffer
> '75 ex Palm Beach
> Tucson, AZ.
> Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive, Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American Eagles,
> Solar battery charging. GMCSJ and GMCMI member
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Larry Davick
A Mystery Machine
1976(ish) Palm Beach
Fremont, Ca
Howell EFI + EBL + Electronic Dizzy
|
|
|
Re: Going after a new (to me) GMC [message #356436 is a reply to message #356106] |
Sun, 05 July 2020 12:15 |
Greg C.
Messages: 224 Registered: October 2019 Location: Knoxville, TN
Karma: 0
|
Senior Member |
|
|
Thanks everyone, for the encouragement and advice.
Carl, very interesting pictures on the vapor return line. I may have to do something like that. Chuck Boyd has suggested I pressurize the fuel pick up lines as a first step in case they are partially clogged.
I just put in a 30 amp RV box on the house garage yesterday for shore power. I promised the wife that I would finish up a couple of projects I have underway before I dive headfirst into the GMC, so I am going to pace my work on it for a bit.
Matt, I updated my sigfile per your suggestion.
Thanks again!
Greg Crawford
KM4ZCR
Knoxville, TN
"Ruby Sue"
1977 Royale
Rear Bath
403 Engine
American Eagle Wheels
Early Version Alex Sirum Quad bags
|
|
|
Re: Going after a new (to me) GMC [message #356444 is a reply to message #356436] |
Sun, 05 July 2020 17:58 |
Carl S.
Messages: 4186 Registered: January 2009 Location: Tucson, AZ.
Karma: 13
|
Senior Member |
|
|
Greg,
I did that vapor return line on the recommendation of another GMCer who had done the same thing and said it cleared up his vapor lock issues completely. It didn't do the trick for me. I'm not sure if it really helps, but it might, so I will leave it that way for now. The main drawback is that it adds a step to changing out the carb filter, but I just eliminated that filter anyway in favor of an additional in-line filter between the steel line and the mechanical fuel pump. The reason I finally decided to eliminate that filter is due to the danger of eventually stretching or stripping the threads in the inlet. Carburetors are not as common as they once were and it would be hard to replace.
Carl Stouffer
'75 ex Palm Beach
Tucson, AZ.
Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive, Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American Eagles, Solar battery charging. GMCSJ and GMCMI member
|
|
|
Goto Forum:
Current Time: Wed Sep 18 18:29:02 CDT 2024
Total time taken to generate the page: 0.00943 seconds
|