Home » Public Forums » GMCnet » Door repair
Door repair [message #352375] |
Mon, 24 February 2020 21:29 |
|
Tom Lins
Messages: 372 Registered: February 2004 Location: St Augustine, FL
Karma: 1
|
Senior Member |
|
|
I have been fixing issues on our GMC as time and funds allow and I finally got to fixing the striker plate that has a wobbly pin.
It jumped up on the list due to acquiring a Birch screen door. I figured I needed to straighten out any issues with the door before trying to install the Birch door.
After installing the replacement striker plate the door seemed to be even more difficult to close completely.
My son noticed the bottom hinge seemed to wobble quite a bit. After some investigation I discovered that the the entire section the hinge bolts to has failed.
I seems that the only reason the hinge did not pull out of the door is because of the bolts would not pull thru nthe slot.
I had to use a piece of 1/8 " steel to reinforce the door to get the door to operate and close properly.
http://www.gmcmhphotos.com/photos/birch-screen-door-install/p67063-door-reinforcment.html
Tom Lins
St Augustine, FL
77 GM Rear Twin, Dry Bath, 455, Aluminum Radiator Quad-Bag Suspension Solar Panel
Manuals on DVD
YOUTUBE Channel: GMC Dealer Training Tapes
http://www.bdub.net/tomlins/
|
|
|
|
|
|
|
|
Re: [GMCnet] Door repair [message #352402 is a reply to message #352398] |
Tue, 25 February 2020 22:27 |
powwerjon
Messages: 849 Registered: March 2013
Karma: -2
|
Senior Member |
|
|
Gaul is the correct definition. I have even used a never-seize type
compound on the threads. If you over tighten SS hardware it can be a pain
to take apart. There are many grades of SS screws and bolts such as 316SS,
High-strength 316SS, 18-8 SS, 17-4 PH SS, Super-Corrosion-Resistant 316 SS
and 450 SS. McMaster-Carr gives a good definition of each and possible
applications.
J.R. Wright
GMC Great Laker
GMCGL Tech Editor
GMC Eastern States
GMCMHI
TZE Zone Restorations
78 Buskirk Custom 29.5' Stretch
75 Avion (Under going Frame up Restoration)
On Tue, Feb 25, 2020 at 8:32 PM Todd Sullivan via Gmclist <
gmclist@list.gmcnet.org> wrote:
> If you are using stainless bolts and nut make sure they are different
> grades otherwise the bolt and nut will gaul or seize.
>
> Sully
> Bellevue wa.
>
> On Tue, Feb 25, 2020 at 5:35 PM Tom Lins via Gmclist gmclist@list.gmcnet.org> wrote:
>
>> They are on order since I had to grind down the heads a bit to get the
>> door to close without interference.
>>
>> --
>> Tom Lins
>> St Augustine, FL
>> 77 GM Rear Twin, Dry Bath, 455, Aluminum Radiator Quad-Bag Suspension
>> Solar Panel
>> Manuals on DVD
>> GMC Dealer Training Tapes
>> http://www.bdub.net/tomlins/
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] Door repair [message #352423 is a reply to message #352402] |
Wed, 26 February 2020 13:44 |
jessfarr
Messages: 100 Registered: August 2004
Karma: 1
|
Senior Member |
|
|
Now, do they recommend which nut works best with which screw or best to use in plain steel nut without galling ?
jofarr
soddy daisy tn, 26' canyonlands
----- Original Message -----
From: John Wright via Gmclist
Reply-To:
To: GMC Net
Cc: John Wright
Sent: 2/25/2020 11:27:56 PM
Subject: Re: [GMCnet] Door repair
________________________________________________________________________________
Gaul is the correct definition. I have even used a never-seize type
compound on the threads. If you over tighten SS hardware it can be a pain
to take apart. There are many grades of SS screws and bolts such as 316SS,
High-strength 316SS, 18-8 SS, 17-4 PH SS, Super-Corrosion-Resistant 316 SS
and 450 SS. McMaster-Carr gives a good definition of each and possible
applications.
J.R. Wright
GMC Great Laker
GMCGL Tech Editor
GMC Eastern States
GMCMHI
TZE Zone Restorations
78 Buskirk Custom 29.5' Stretch
75 Avion (Under going Frame up Restoration)
On Tue, Feb 25, 2020 at 8:32 PM Todd Sullivan via Gmclist <
gmclist@list.gmcnet.org> wrote:
> If you are using stainless bolts and nut make sure they are different
> grades otherwise the bolt and nut will gaul or seize.
>
> Sully
> Bellevue wa.
>
> On Tue, Feb 25, 2020 at 5:35 PM Tom Lins via Gmclist gmclist@list.gmcnet.org> wrote:
>
>> They are on order since I had to grind down the heads a bit to get the
>> door to close without interference.
>>
>> --
>> Tom Lins
>> St Augustine, FL
>> 77 GM Rear Twin, Dry Bath, 455, Aluminum Radiator Quad-Bag Suspension
>> Solar Panel
>> Manuals on DVD
>> GMC Dealer Training Tapes
>> http://www.bdub.net/tomlins/
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
jesse farr, soddy tn USA '74 Canyonlands 260
|
|
|
Re: [GMCnet] Door repair [message #352424 is a reply to message #352398] |
Wed, 26 February 2020 13:56 |
powwerjon
Messages: 849 Registered: March 2013
Karma: -2
|
Senior Member |
|
|
What Sully said about using different grades! if your using a 304 or 316
SS steel bolt and nut assembly which is a softer alloy as compared to 18-8
and 17-4 grades that are somewhat harder. Also most people have a
difficult time on how tight the assembly should be. Us a torque chart and
torque wrench. The adage of tight is good, tighter is better is wrong. It
is either gauled or snapped of when you get it that tight. You can feel it
when it gauls. the fastener slips slightly and then does not move in any
direction and you typical snap it off.
J.R. Wright
GMC Great Laker
GMCGL Tech Editor
GMC Eastern States
GMCMHI
TZE Zone Restorations
78 Buskirk Custom 29.5' Stretch
75 Avion (Under going Frame up Restoration)
On Wed, Feb 26, 2020 at 12:45 PM Jesse Farr via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Now, do they recommend which nut works best with which screw or best to
> use in plain steel nut without galling ?
>
> jofarr
> soddy daisy tn, 26' canyonlands
>
>
> ----- Original Message -----
> From: John Wright via Gmclist
> Reply-To:
> To: GMC Net
> Cc: John Wright
> Sent: 2/25/2020 11:27:56 PM
> Subject: Re: [GMCnet] Door repair
>
> ________________________________________________________________________________
>
> Gaul is the correct definition. I have even used a never-seize type
> compound on the threads. If you over tighten SS hardware it can be a pain
> to take apart. There are many grades of SS screws and bolts such as 316SS,
> High-strength 316SS, 18-8 SS, 17-4 PH SS, Super-Corrosion-Resistant 316 SS
> and 450 SS. McMaster-Carr gives a good definition of each and possible
> applications.
>
> J.R. Wright
> GMC Great Laker
> GMCGL Tech Editor
> GMC Eastern States
> GMCMHI
> TZE Zone Restorations
> 78 Buskirk Custom 29.5' Stretch
> 75 Avion (Under going Frame up Restoration)
>
>
>
> On Tue, Feb 25, 2020 at 8:32 PM Todd Sullivan via Gmclist gmclist@list.gmcnet.org> wrote:
>
>> If you are using stainless bolts and nut make sure they are different
>> grades otherwise the bolt and nut will gaul or seize.
>>
>> Sully
>> Bellevue wa.
>>
>> On Tue, Feb 25, 2020 at 5:35 PM Tom Lins via Gmclist > gmclist@list.gmcnet.org> wrote:
>>
>>> They are on order since I had to grind down the heads a bit to get the
>>> door to close without interference.
>>>
>>> --
>>> Tom Lins
>>> St Augustine, FL
>>> 77 GM Rear Twin, Dry Bath, 455, Aluminum Radiator Quad-Bag Suspension
>>> Solar Panel
>>> Manuals on DVD
>>> GMC Dealer Training Tapes
>>> http://www.bdub.net/tomlins/
>>>
>>> _______________________________________________
>>> GMCnet mailing list
>>> Unsubscribe or Change List Options:
>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] Door repair [message #352425 is a reply to message #352424] |
Wed, 26 February 2020 14:26 |
Ken Henderson
Messages: 8726 Registered: March 2004 Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
John,
I guess you don't agree with my grandaddy's rule: "If 1 nail's enough, 2's
better, and 3 should be 'just about right'". :-)
Ken H.
On Wed, Feb 26, 2020 at 2:57 PM John Wright via Gmclist <
gmclist@list.gmcnet.org> wrote:
> What Sully said about using different grades! if your using a 304 or 316
> SS steel bolt and nut assembly which is a softer alloy as compared to 18-8
> and 17-4 grades that are somewhat harder. Also most people have a
> difficult time on how tight the assembly should be. Us a torque chart and
> torque wrench. The adage of tight is good, tighter is better is wrong. It
> is either gauled or snapped of when you get it that tight. You can feel it
> when it gauls. the fastener slips slightly and then does not move in any
> direction and you typical snap it off.
>
> J.R. Wright
> GMC Great Laker
> GMCGL Tech Editor
> GMC Eastern States
> GMCMHI
> TZE Zone Restorations
> 78 Buskirk Custom 29.5' Stretch
> 75 Avion (Under going Frame up Restoration)
>
>
>
> On Wed, Feb 26, 2020 at 12:45 PM Jesse Farr via Gmclist gmclist@list.gmcnet.org> wrote:
>
>> Now, do they recommend which nut works best with which screw or best to
>> use in plain steel nut without galling ?
>>
>> jofarr
>> soddy daisy tn, 26' canyonlands
>>
>>
>> ----- Original Message -----
>> From: John Wright via Gmclist
>> Reply-To:
>> To: GMC Net
>> Cc: John Wright
>> Sent: 2/25/2020 11:27:56 PM
>> Subject: Re: [GMCnet] Door repair
>>
>>
> ________________________________________________________________________________
>>
>> Gaul is the correct definition. I have even used a never-seize type
>> compound on the threads. If you over tighten SS hardware it can be a
> pain
>> to take apart. There are many grades of SS screws and bolts such as
> 316SS,
>> High-strength 316SS, 18-8 SS, 17-4 PH SS, Super-Corrosion-Resistant 316
> SS
>> and 450 SS. McMaster-Carr gives a good definition of each and possible
>> applications.
>>
>> J.R. Wright
>> GMC Great Laker
>> GMCGL Tech Editor
>> GMC Eastern States
>> GMCMHI
>> TZE Zone Restorations
>> 78 Buskirk Custom 29.5' Stretch
>> 75 Avion (Under going Frame up Restoration)
>>
>>
>>
>> On Tue, Feb 25, 2020 at 8:32 PM Todd Sullivan via Gmclist > gmclist@list.gmcnet.org> wrote:
>>
>>> If you are using stainless bolts and nut make sure they are different
>>> grades otherwise the bolt and nut will gaul or seize.
>>>
>>> Sully
>>> Bellevue wa.
>>>
>>> On Tue, Feb 25, 2020 at 5:35 PM Tom Lins via Gmclist >> gmclist@list.gmcnet.org> wrote:
>>>
>>>> They are on order since I had to grind down the heads a bit to get
> the
>>>> door to close without interference.
>>>>
>>>> --
>>>> Tom Lins
>>>> St Augustine, FL
>>>> 77 GM Rear Twin, Dry Bath, 455, Aluminum Radiator Quad-Bag
> Suspension
>>>> Solar Panel
>>>> Manuals on DVD
>>>> GMC Dealer Training Tapes
>>>> http://www.bdub.net/tomlins/
>>>>
>>>> _______________________________________________
>>>> GMCnet mailing list
>>>> Unsubscribe or Change List Options:
>>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>>
>>> _______________________________________________
>>> GMCnet mailing list
>>> Unsubscribe or Change List Options:
>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
Re: [GMCnet] Door repair [message #352426 is a reply to message #352423] |
Wed, 26 February 2020 15:33 |
sgltrac
Messages: 2797 Registered: April 2011
Karma: 1
|
Senior Member |
|
|
Jesse,
The hardware suppliers and manufacturers are aware of this so typically the
nuts and bolts are made from different alloys but it’s a question that
should be asked when sourcing to ensure you don’t end up with a set from
same grade of stainless.
The way I discovered this issue was in the removal of stainless truck stake
pocket retractable hooks. The screws supplied with the hooks were the same
alloy and upon removal of the hooks I ended up snapping the screws off in
the hooks. This surprised me as there was no corrosion present and the
screws were not cross threaded. I few questions later at Tacoma Screw I had
the answer.
Sully
Bellevue wa
On Wed, Feb 26, 2020 at 11:45 AM Jesse Farr via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Now, do they recommend which nut works best with which screw or best to
> use in plain steel nut without galling ?
>
> jofarr
> soddy daisy tn, 26' canyonlands
>
>
> ----- Original Message -----
> From: John Wright via Gmclist
> Reply-To:
> To: GMC Net
> Cc: John Wright
> Sent: 2/25/2020 11:27:56 PM
> Subject: Re: [GMCnet] Door repair
>
> ________________________________________________________________________________
>
> Gaul is the correct definition. I have even used a never-seize type
> compound on the threads. If you over tighten SS hardware it can be a pain
> to take apart. There are many grades of SS screws and bolts such as 316SS,
> High-strength 316SS, 18-8 SS, 17-4 PH SS, Super-Corrosion-Resistant 316 SS
> and 450 SS. McMaster-Carr gives a good definition of each and possible
> applications.
>
> J.R. Wright
> GMC Great Laker
> GMCGL Tech Editor
> GMC Eastern States
> GMCMHI
> TZE Zone Restorations
> 78 Buskirk Custom 29.5' Stretch
> 75 Avion (Under going Frame up Restoration)
>
>
>
> On Tue, Feb 25, 2020 at 8:32 PM Todd Sullivan via Gmclist gmclist@list.gmcnet.org> wrote:
>
>> If you are using stainless bolts and nut make sure they are different
>> grades otherwise the bolt and nut will gaul or seize.
>>
>> Sully
>> Bellevue wa.
>>
>> On Tue, Feb 25, 2020 at 5:35 PM Tom Lins via Gmclist > gmclist@list.gmcnet.org> wrote:
>>
>>> They are on order since I had to grind down the heads a bit to get the
>>> door to close without interference.
>>>
>>> --
>>> Tom Lins
>>> St Augustine, FL
>>> 77 GM Rear Twin, Dry Bath, 455, Aluminum Radiator Quad-Bag Suspension
>>> Solar Panel
>>> Manuals on DVD
>>> GMC Dealer Training Tapes
>>> http://www.bdub.net/tomlins/
>>>
>>> _______________________________________________
>>> GMCnet mailing list
>>> Unsubscribe or Change List Options:
>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Sully
77 Royale basket case.
Future motorhome land speed record holder(bucket list)
Seattle, Wa.
|
|
|
Re: [GMCnet] Door repair [message #352430 is a reply to message #352426] |
Wed, 26 February 2020 16:32 |
powwerjon
Messages: 849 Registered: March 2013
Karma: -2
|
Senior Member |
|
|
Ken,
Remember the big hammer and 36" pipe wrench, i can get anything apart!!
J.R.
On Wed, Feb 26, 2020 at 2:34 PM Todd Sullivan via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Jesse,
>
> The hardware suppliers and manufacturers are aware of this so typically the
> nuts and bolts are made from different alloys but it’s a question that
> should be asked when sourcing to ensure you don’t end up with a set from
> same grade of stainless.
> The way I discovered this issue was in the removal of stainless truck stake
> pocket retractable hooks. The screws supplied with the hooks were the same
> alloy and upon removal of the hooks I ended up snapping the screws off in
> the hooks. This surprised me as there was no corrosion present and the
> screws were not cross threaded. I few questions later at Tacoma Screw I had
> the answer.
>
> Sully
> Bellevue wa
>
> On Wed, Feb 26, 2020 at 11:45 AM Jesse Farr via Gmclist gmclist@list.gmcnet.org> wrote:
>
>> Now, do they recommend which nut works best with which screw or best to
>> use in plain steel nut without galling ?
>>
>> jofarr
>> soddy daisy tn, 26' canyonlands
>>
>>
>> ----- Original Message -----
>> From: John Wright via Gmclist
>> Reply-To:
>> To: GMC Net
>> Cc: John Wright
>> Sent: 2/25/2020 11:27:56 PM
>> Subject: Re: [GMCnet] Door repair
>>
>>
> ________________________________________________________________________________
>>
>> Gaul is the correct definition. I have even used a never-seize type
>> compound on the threads. If you over tighten SS hardware it can be a
> pain
>> to take apart. There are many grades of SS screws and bolts such as
> 316SS,
>> High-strength 316SS, 18-8 SS, 17-4 PH SS, Super-Corrosion-Resistant 316
> SS
>> and 450 SS. McMaster-Carr gives a good definition of each and possible
>> applications.
>>
>> J.R. Wright
>> GMC Great Laker
>> GMCGL Tech Editor
>> GMC Eastern States
>> GMCMHI
>> TZE Zone Restorations
>> 78 Buskirk Custom 29.5' Stretch
>> 75 Avion (Under going Frame up Restoration)
>>
>>
>>
>> On Tue, Feb 25, 2020 at 8:32 PM Todd Sullivan via Gmclist > gmclist@list.gmcnet.org> wrote:
>>
>>> If you are using stainless bolts and nut make sure they are different
>>> grades otherwise the bolt and nut will gaul or seize.
>>>
>>> Sully
>>> Bellevue wa.
>>>
>>> On Tue, Feb 25, 2020 at 5:35 PM Tom Lins via Gmclist >> gmclist@list.gmcnet.org> wrote:
>>>
>>>> They are on order since I had to grind down the heads a bit to get
> the
>>>> door to close without interference.
>>>>
>>>> --
>>>> Tom Lins
>>>> St Augustine, FL
>>>> 77 GM Rear Twin, Dry Bath, 455, Aluminum Radiator Quad-Bag
> Suspension
>>>> Solar Panel
>>>> Manuals on DVD
>>>> GMC Dealer Training Tapes
>>>> http://www.bdub.net/tomlins/
>>>>
>>>> _______________________________________________
>>>> GMCnet mailing list
>>>> Unsubscribe or Change List Options:
>>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>>
>>> _______________________________________________
>>> GMCnet mailing list
>>> Unsubscribe or Change List Options:
>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] Door repair [message #352435 is a reply to message #352430] |
Wed, 26 February 2020 18:48 |
jessfarr
Messages: 100 Registered: August 2004
Karma: 1
|
Senior Member |
|
|
Hard to get that 36" pipe wrench inside the nut where broken off though
jofarr, soddy daisy tn, 26' canyonland
----- Original Message -----
From: John Wright via Gmclist
Reply-To:
To: GMC Net
Cc: John Wright
Sent: 2/26/2020 5:32:28 PM
Subject: Re: [GMCnet] Door repair
________________________________________________________________________________
Ken,
Remember the big hammer and 36" pipe wrench, i can get anything apart!!
J.R.
On Wed, Feb 26, 2020 at 2:34 PM Todd Sullivan via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Jesse,
>
> The hardware suppliers and manufacturers are aware of this so typically the
> nuts and bolts are made from different alloys but it’s a question that
> should be asked when sourcing to ensure you don’t end up with a set from
> same grade of stainless.
> The way I discovered this issue was in the removal of stainless truck stake
> pocket retractable hooks. The screws supplied with the hooks were the same
> alloy and upon removal of the hooks I ended up snapping the screws off in
> the hooks. This surprised me as there was no corrosion present and the
> screws were not cross threaded. I few questions later at Tacoma Screw I had
> the answer.
>
> Sully
> Bellevue wa
>
> On Wed, Feb 26, 2020 at 11:45 AM Jesse Farr via Gmclist gmclist@list.gmcnet.org> wrote:
>
>> Now, do they recommend which nut works best with which screw or best to
>> use in plain steel nut without galling ?
>>
>> jofarr
>> soddy daisy tn, 26' canyonlands
>>
>>
>> ----- Original Message -----
>> From: John Wright via Gmclist
>> Reply-To:
>> To: GMC Net
>> Cc: John Wright
>> Sent: 2/25/2020 11:27:56 PM
>> Subject: Re: [GMCnet] Door repair
>>
>>
> ________________________________________________________________________________
>>
>> Gaul is the correct definition. I have even used a never-seize type
>> compound on the threads. If you over tighten SS hardware it can be a
> pain
>> to take apart. There are many grades of SS screws and bolts such as
> 316SS,
>> High-strength 316SS, 18-8 SS, 17-4 PH SS, Super-Corrosion-Resistant 316
> SS
>> and 450 SS. McMaster-Carr gives a good definition of each and possible
>> applications.
>>
>> J.R. Wright
>> GMC Great Laker
>> GMCGL Tech Editor
>> GMC Eastern States
>> GMCMHI
>> TZE Zone Restorations
>> 78 Buskirk Custom 29.5' Stretch
>> 75 Avion (Under going Frame up Restoration)
>>
>>
>>
>> On Tue, Feb 25, 2020 at 8:32 PM Todd Sullivan via Gmclist > gmclist@list.gmcnet.org> wrote:
>>
>>> If you are using stainless bolts and nut make sure they are different
>>> grades otherwise the bolt and nut will gaul or seize.
>>>
>>> Sully
>>> Bellevue wa.
>>>
>>> On Tue, Feb 25, 2020 at 5:35 PM Tom Lins via Gmclist >> gmclist@list.gmcnet.org> wrote:
>>>
>>>> They are on order since I had to grind down the heads a bit to get
> the
>>>> door to close without interference.
>>>>
>>>> --
>>>> Tom Lins
>>>> St Augustine, FL
>>>> 77 GM Rear Twin, Dry Bath, 455, Aluminum Radiator Quad-Bag
> Suspension
>>>> Solar Panel
>>>> Manuals on DVD
>>>> GMC Dealer Training Tapes
>>>> http://www.bdub.net/tomlins/
>>>>
>>>> _______________________________________________
>>>> GMCnet mailing list
>>>> Unsubscribe or Change List Options:
>>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>>
>>> _______________________________________________
>>> GMCnet mailing list
>>> Unsubscribe or Change List Options:
>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
jesse farr, soddy tn USA '74 Canyonlands 260
|
|
|
Goto Forum:
Current Time: Thu Sep 19 16:21:23 CDT 2024
Total time taken to generate the page: 0.00931 seconds
|