GMCforum: GMCnet » Want to make sure I'm doing this right

Home » Public Forums » GMCnet » Want to make sure I'm doing this right (Shock Bushings)

Show: Today's Messages :: Polls :: Message Navigator

Want to make sure I'm doing this right [message #351239]

Sun, 05 January 2020 09:13

uprooted

Messages: 72
Registered: December 2019
Location: Hilliard, OH

Karma: 0

Member

In reading the write-up found here: http://gmcmotorhome.info/services.html, I see that it says that the front shocks use part number 9.8108 (2 halves per each end of each shock). I'm a little confused because, if I'm cutting them in half why would 4 boxes be required for the front shocks? Each shock end should just require one bushing if you do it like in my photos below. Should just need 2 boxes for the front. Makes me think I'm doing it wrong!

http://www.gmcmhphotos.com/photos/data/7266/bushing_halves.JPG

http://www.gmcmhphotos.com/photos/data/7266/medium/bushings.JPG

Thanks in advance

Corey P / Hilliard, OH / 1974 Glacier 26' / 3.70 FD / ION Wheels

Report message to a moderator

Re: [GMCnet] Want to make sure I'm doing this right [message #351244 is a reply to message #351239]

Sun, 05 January 2020 13:57

sgltrac

Messages: 2797
Registered: April 2011

Karma: 1

Senior Member

There is an inner and outer bushing at each end. You should not be cutting
anything.

Sully
Bellevue wa

On Sun, Jan 5, 2020 at 7:13 AM Corey via Gmclist
wrote:

> In reading the write-up found here: http://gmcmotorhome.info/services.html,
> I see that it says that the front shocks use part number 9.8108 (2 halves
> per each end of each shock). I'm a little confused because, if I'm cutting
> them in half why would 4 boxes be required for the front shocks? Each shock
> end should just require one bushing if you do it like in my photos below.
> Should just need 2 boxes for the front. Makes me think I'm doing it wrong!
>
> http://www.gmcmhphotos.com/photos/data/7266/bushing_halves.JPG
>
> http://www.gmcmhphotos.com/photos/data/7266/medium/bushings.JPG
>
> Thanks in advance
> --
> Corey P /
>
> Hilliard, OH /
>
> 1974 Glacier 26'
>
> ION Wheels
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org

Sully 77 Royale basket case. Future motorhome land speed record holder(bucket list) Seattle, Wa.

Report message to a moderator

Re: [GMCnet] Want to make sure I'm doing this right [message #351254 is a reply to message #351244]

Sun, 05 January 2020 23:17

Bullitthead

Messages: 1411
Registered: November 2013

Karma: 5

Senior Member

Those type of bushings are already installed on new shocks...and what Sully said, you should not be cutting anything, even if you were replacing the bushings on some old shocks.

Terry Kelpien ASE Master Technician 73 Glacier 260 Smithfield, Va.

Report message to a moderator

Re: [GMCnet] Want to make sure I'm doing this right [message #351256 is a reply to message #351254]

Mon, 06 January 2020 06:35

Ken Burton

Messages: 10030
Registered: January 2004
Location: Hebron, Indiana

Karma: 10

Senior Member

I am not sure the above statements are true for Energy Suspension bushings. These things unlike rubber ones, are nearly solid and I am not sure that they can be pressed in without splitting them. I have pressed in Energy Suspension control arm bushings which are straight, but these shock bushings are tapered in the middle. You might want to read the installation instructions or call Energy Suspension and ask.

Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana

Report message to a moderator

Re: [GMCnet] Want to make sure I'm doing this right [message #351278 is a reply to message #351256]

Mon, 06 January 2020 13:08

powwerjon

Messages: 849
Registered: March 2013

Karma: -2

Senior Member

Don't cut, they can be pressed in either with a hydraulic press or a screw
arrangement similar to the device that install the upper and lower
bushings. Just use silicone grease and press away.

J.R. Wright
GMC Great Laker
GMCGL Tech Editor
GMC Eastern States
GMCMHI
TZE Zone Restorations
78 Buskirk Custom 29.5' Stretch
75 Avion (Under going Frame up Restoration)

On Mon, Jan 6, 2020 at 5:35 AM Ken Burton via Gmclist <
gmclist@list.gmcnet.org> wrote:

> I am not sure the above statements are true for Energy Suspension
> bushings. These things unlike rubber ones, are nearly solid and I am not
> sure that
> they can be pressed in without splitting them. I have pressed in Energy
> Suspension control arm bushings which are straight, but these shock bushings
> are tapered in the middle. You might want to read the installation
> instructions or call Energy Suspension and ask.
> --
> Ken Burton - N9KB
> 76 Palm Beach
> Hebron, Indiana
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org

Report message to a moderator

Re: Want to make sure I'm doing this right [message #351363 is a reply to message #351239]

Sat, 11 January 2020 08:35

uprooted

Messages: 72
Registered: December 2019
Location: Hilliard, OH

Karma: 0

Member

Does anyone have photos or a link to the correct bushings? I'm confused a to why the write-up calls for "2 halves" on each end of the rear shocks. When I ordered the Energy Suspension part number that was referenced a got a box that had what appear to be two whole bushings in it. As Ken said they are tapered in the middle. I'm not sure they're the right fit, as the shock bushing eye is straight if not wider towards the middle.

Corey P / Hilliard, OH / 1974 Glacier 26' / 3.70 FD / ION Wheels

Report message to a moderator

Re: Want to make sure I'm doing this right [message #351365 is a reply to message #351239]

Sat, 11 January 2020 10:35

JohnL455

Messages: 4447
Registered: October 2006
Location: Woodstock, IL

Karma: 12

Senior Member

Dumb question. Aren't both KYB and Bilsteins both lifetime warranty? If bushings bad get new shocks for free as a bonus. Please explain.

John Lebetski
Woodstock, IL
77 Eleganza II

Report message to a moderator

Re: Want to make sure I'm doing this right [message #351372 is a reply to message #351239]

Sun, 12 January 2020 12:55

jhbridges

Messages: 8412
Registered: May 2011
Location: Braselton ga

Karma: -74

Senior Member

I believe Jimmy the K warrants Builstein that way. KYB does anyway. Ask him.

--johnny

Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons. Braselton, Ga. I forgive them all, save those who hurt the dogs. They must answer to me in hell

Report message to a moderator

Re: Want to make sure I'm doing this right [message #351509 is a reply to message #351239]

Tue, 21 January 2020 23:24

uprooted

Messages: 72
Registered: December 2019
Location: Hilliard, OH

Karma: 0

Member

Good point on the warranty!

Corey P / Hilliard, OH / 1974 Glacier 26' / 3.70 FD / ION Wheels

Report message to a moderator

Previous Topic:	Re: [GMCnet] Re Electric Vehicles
Next Topic:	Factory bottle jack replacement

Goto Forum:

-=] Back to Top [=-

Current Time: Thu Sep 19 20:27:56 CDT 2024

Total time taken to generate the page: 0.02439 seconds