Home » Public Forums » GMCnet » [GMCnet] 455 spark plugs
[GMCnet] 455 spark plugs [message #350614] |
Wed, 11 December 2019 11:10 |
Emery Stora
Messages: 959 Registered: January 2011
Karma: 4
|
Senior Member |
|
|
I forgot to say that Dick Paterson recommends always using a torque wrench when installing plugs.
Most of us just spin them in and lean on the wrench.
Dick says to torque them to 26-30 ft-lbs.
Over torque can distort the thin base and fracture the “gas tight” seals between the porcelain and metal base.
Emery Stora
77 Kingsley
Frederick, CO
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] 455 spark plugs [message #350615 is a reply to message #350614] |
Wed, 11 December 2019 11:27 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
Also the gap not to exceed .040.
There are books that call for .080, that was changed by GM, but it cannot
be erased, just like the front wheel alignment specs.
On Wed, Dec 11, 2019 at 9:10 AM Emery Stora via Gmclist <
gmclist@list.gmcnet.org> wrote:
> I forgot to say that Dick Paterson recommends always using a torque wrench
> when installing plugs.
> Most of us just spin them in and lean on the wrench.
> Dick says to torque them to 26-30 ft-lbs.
> Over torque can distort the thin base and fracture the “gas tight” seals
> between the porcelain and metal base.
>
> Emery Stora
> 77 Kingsley
> Frederick, CO
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmcrvparts.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Re: [GMCnet] 455 spark plugs [message #350616 is a reply to message #350615] |
Wed, 11 December 2019 13:30 |
Jerry Wheeler
Messages: 246 Registered: January 2013
Karma: 2
|
Senior Member |
|
|
What did Dick say for an Olds 403 engine??
JR Wheeler 78 Royale 73 Painted Desert
On Wed, Dec 11, 2019 at 12:28 PM Jim Kanomata via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Also the gap not to exceed .040.
> There are books that call for .080, that was changed by GM, but it cannot
> be erased, just like the front wheel alignment specs.
>
>
> On Wed, Dec 11, 2019 at 9:10 AM Emery Stora via Gmclist gmclist@list.gmcnet.org> wrote:
>
>> I forgot to say that Dick Paterson recommends always using a torque
> wrench
>> when installing plugs.
>> Most of us just spin them in and lean on the wrench.
>> Dick says to torque them to 26-30 ft-lbs.
>> Over torque can distort the thin base and fracture the “gas tight” seals
>> between the porcelain and metal base.
>>
>> Emery Stora
>> 77 Kingsley
>> Frederick, CO
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
>
>
> --
> Jim Kanomata
> Applied/GMC, Newark,CA
> jimk@appliedairfilters.com
> http://www.appliedgmcrvparts.com
> 1-800-752-7502
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] 455 spark plugs [message #350617 is a reply to message #350616] |
Wed, 11 December 2019 13:57 |
Emery Stora
Messages: 959 Registered: January 2011
Karma: 4
|
Senior Member |
|
|
Since I don’t have a 403 I didn’t ask him. It’s likely the same plug but perhaps you should email him and ask.
Emery Stora
77 Kingsley
Frederick CO
> On Dec 11, 2019, at 12:30 PM, Jerry Wheeler via Gmclist wrote:
>
> What did Dick say for an Olds 403 engine??
> JR Wheeler 78 Royale 73 Painted Desert
>
>
> On Wed, Dec 11, 2019 at 12:28 PM Jim Kanomata via Gmclist gmclist@list.gmcnet.org> wrote:
>
>> Also the gap not to exceed .040.
>> There are books that call for .080, that was changed by GM, but it cannot
>> be erased, just like the front wheel alignment specs.
>>
>>
>> On Wed, Dec 11, 2019 at 9:10 AM Emery Stora via Gmclist > gmclist@list.gmcnet.org> wrote:
>>
>>> I forgot to say that Dick Paterson recommends always using a torque
>> wrench
>>> when installing plugs.
>>> Most of us just spin them in and lean on the wrench.
>>> Dick says to torque them to 26-30 ft-lbs.
>>> Over torque can distort the thin base and fracture the “gas tight” seals
>>> between the porcelain and metal base.
>>>
>>> Emery Stora
>>> 77 Kingsley
>>> Frederick, CO
>>> _______________________________________________
>>> GMCnet mailing list
>>> Unsubscribe or Change List Options:
>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>
>>
>>
>> --
>> Jim Kanomata
>> Applied/GMC, Newark,CA
>> jimk@appliedairfilters.com
>> http://www.appliedgmcrvparts.com
>> 1-800-752-7502
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] 455 spark plugs [message #350618 is a reply to message #350617] |
Wed, 11 December 2019 14:50 |
powwerjon
Messages: 849 Registered: March 2013
Karma: -2
|
Senior Member |
|
|
Jerry,
I wrote a complete spark plug guide for the 455 and 403 and including Onan
& Gererac generators. I am presently in AZ for the winter and don't have a
copy to current version on my laptop. I had worked with Dick Paterson on
the current plugs that he recommended. If anyone out there has a PDF of
the doc please send it to Jerry or post it. The current version onn GMCMI
does not work and I will be contacting Kim to try and correct it.
J.R. Wright
GMC Great Laker
GMCGL Tech Editor
GMC Eastern States
GMCMHI
TZE Zone Restorations
78 Buskirk Custom 29.5' Stretch
75 Avion (Under going Frame up Restoration)
On Wed, Dec 11, 2019 at 12:58 PM Emery Stora via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Since I don’t have a 403 I didn’t ask him. It’s likely the same plug but
> perhaps you should email him and ask.
>
> Emery Stora
> 77 Kingsley
> Frederick CO
>
>> On Dec 11, 2019, at 12:30 PM, Jerry Wheeler via Gmclist gmclist@list.gmcnet.org> wrote:
>>
>> What did Dick say for an Olds 403 engine??
>> JR Wheeler 78 Royale 73 Painted Desert
>>
>>
>> On Wed, Dec 11, 2019 at 12:28 PM Jim Kanomata via Gmclist > gmclist@list.gmcnet.org> wrote:
>>
>>> Also the gap not to exceed .040.
>>> There are books that call for .080, that was changed by GM, but it
> cannot
>>> be erased, just like the front wheel alignment specs.
>>>
>>>
>>> On Wed, Dec 11, 2019 at 9:10 AM Emery Stora via Gmclist >> gmclist@list.gmcnet.org> wrote:
>>>
>>>> I forgot to say that Dick Paterson recommends always using a torque
>>> wrench
>>>> when installing plugs.
>>>> Most of us just spin them in and lean on the wrench.
>>>> Dick says to torque them to 26-30 ft-lbs.
>>>> Over torque can distort the thin base and fracture the “gas tight”
> seals
>>>> between the porcelain and metal base.
>>>>
>>>> Emery Stora
>>>> 77 Kingsley
>>>> Frederick, CO
>>>> _______________________________________________
>>>> GMCnet mailing list
>>>> Unsubscribe or Change List Options:
>>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>>
>>>
>>>
>>> --
>>> Jim Kanomata
>>> Applied/GMC, Newark,CA
>>> jimk@appliedairfilters.com
>>> http://www.appliedgmcrvparts.com
>>> 1-800-752-7502
>>> _______________________________________________
>>> GMCnet mailing list
>>> Unsubscribe or Change List Options:
>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] 455 spark plugs [message #350619 is a reply to message #350617] |
Wed, 11 December 2019 15:04 |
Ty Hardiman
Messages: 43 Registered: April 2017 Location: Norman, Oklahoma
Karma: 0
|
Member |
|
|
The way I see it, there are three factory engine scenarios. A 455 with the points ignition, a 455 with HEI, and a 403 with HEI.
Dick Patterson's position is that they all get the same plug and the same gap. I talked to him about this in October.
Norman, OK / August 1977 Kingsley / 403 / 3.55 / 16" / Quadrajet
|
|
|
Re: [GMCnet] 455 spark plugs [message #350623 is a reply to message #350619] |
Wed, 11 December 2019 19:52 |
|
Matt Colie
Messages: 8547 Registered: March 2007 Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
Ty Hardiman wrote on Wed, 11 December 2019 16:04The way I see it, there are three factory engine scenarios. A 455 with the points ignition, a 455 with HEI, and a 403 with HEI.
Dick Patterson's position is that they all get the same plug and the same gap. I talked to him about this in October.
I have been running NGK XR451X for a very long time. I did not even replace them during the recent overhaul. At Marco, we did a lot of testing for NGK.
At McCord, we made all the gaskets for Champion and A/C for years. The most reliable way to seat the gasket was torque and turn and not torque alone.
Being an ex-engine lab rat, that is why I don't have one of those as listed above.
GM's attempt with HEI was to use the spark energy to reduce misfires that were a big problem in emissions in the early game. If you can do it, it can work in your favor for both emissions and fuel economy. I have done both created my own data and seen the test results. So, I almost redid what we did then that was successful. I say almost because the test engines had an Mallory optical trigger instead of points and it was unreliable even in the test cell. That is why I went with Pertronix as soon as I got the rest of the coach right. I still have it. At first it had a MSD CDI attached to it, but that crashed. So, I dug around in my barn, (those that have been in my barn will believe) and came up with a Mark X CDI by Delta C.1974. It failed the C1 about a year later but I had already procured a Mark XB. It is very similar device with minor improvements. It has been firing those XR451X set at 0.060 for at least 50K mi, and maybe more. (It is cold out where the coach's maintenance log is right now.)
I will put in the warning right now. There are two big issues with this game that you should know about.
First is that the secondary ignition has to be top notch. If it is not, it will not just leak, but common parts may just blow up.
Second is that if you are not a electric shock masochist, stay away while it is running. That level of secondary voltage is out to get you. GOOD!!
The thing I am still missing is how to do an knock controlled spark, but I am working on that. I don't want to have to hammer the air filter housing to fit in the later model distributor.
Matt - The refugee from Dyno-Land
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
Re: [GMCnet] 455 spark plugs [message #350626 is a reply to message #350623] |
Wed, 11 December 2019 23:01 |
Hal StClair
Messages: 971 Registered: March 2013 Location: Rio Rancho NM
Karma: -12
|
Senior Member |
|
|
Matt, you reminded me with your talk of some 'electric shock therapy' of a little competition orange Fiat 600 I had in the early 70's. It had the 600 cc motor .040 over with a little head work, a custom Isky stick, headers, Webers and a Vertex magneto that would let you taste the fillings in your mouth when you got too close-and I did a few times I'm afraid. Fun times and memories.
Hal
"I enjoy talking to you. Your mind appeals to me. It resembles my own mind, except you happen to be insane."
1977 Royale 101348,
1977 Royale 101586, Diesel powered,
1974 Eagle Bus 45',w/slideout,
Rio Rancho, NM
[Updated on: Wed, 11 December 2019 23:01] Report message to a moderator
|
|
|
Re: [GMCnet] 455 spark plugs [message #350627 is a reply to message #350626] |
Wed, 11 December 2019 23:16 |
James Hupy
Messages: 6806 Registered: May 2010
Karma: -62
|
Senior Member |
|
|
Ah yes, Scintilla/Vertex magneto's. Been there, done that. Got the memories
as a reminder to not get intimately involved with them. They will light
your fire, properly set up. The faster they turn, the more spark they make.
Jim Hupy
Salem, Oregon
On Wed, Dec 11, 2019, 9:04 PM Hal StClair via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Matt, you reminded me with you talk of some 'electric shock therapy' of a
> little competition orange Fiat 600 I had in the early 70's. It had the 600
> cc motor .040 over with a little head work, a custom Isky stick, headers,
> Webers and a Vertex magneto that would let you taste the fillings in your
> mouth when you got too close-and I did a few times I'm afraid. Fun times
> and memories.
> Hal
> --
> 1977 Royale 101348,
>
> 1977 Royale 101586, Diesel powered,
>
> 1975 Eleganza II, 101230,
>
> 1974 Eagle Bus 45',w/slideout,
>
> Rio Rancho, NM
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|
Re: [GMCnet] 455 spark plugs [message #350666 is a reply to message #350614] |
Fri, 13 December 2019 17:19 |
jhbridges
Messages: 8412 Registered: May 2011 Location: Braselton ga
Karma: -74
|
Senior Member |
|
|
So it should retard the spark when a knock or knocks is/are sensed? does the system need to do anything else such as rich up the mixture, or goose the waste gate a bit?
--johnny
Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.
I forgive them all, save those who hurt the dogs. They must answer to me in hell
|
|
|
Re: [GMCnet] 455 spark plugs [message #350669 is a reply to message #350666] |
Fri, 13 December 2019 20:58 |
mghamms
Messages: 466 Registered: March 2016 Location: Ware, Massachusetts
Karma: 2
|
Senior Member |
|
|
ebay has the BOSCH PLATINUM # 4023 for $1.26 each with free shipping.
1977 Kingsley 455 as stock as it gets except lots of Ragusa parts
|
|
|
Goto Forum:
Current Time: Sat Sep 21 07:38:14 CDT 2024
Total time taken to generate the page: 0.03684 seconds
|