Tranny [message #343232] |
Fri, 10 May 2019 12:15 |
Bierman
Messages: 46 Registered: May 2017 Location: SW Florida
Karma: 0
|
Member |
|
|
What is the consensus of the forum of which type of Transmission gasket should be used...Cork or the rubber one that comes with the filter kit?
Also going to replace the pan with Applieds new aluminum pan, has anyone used it yet? If so, what should the torque be and any comments on the new pan
Thank You
Member, GMCI, Sunshine Statesman and Dixielanders
26' 1978 Eleganza II, new(rebuilt by Sirum) 403, Lenzi hubs and knuckles, front end by Ferrara
|
|
|
Re: Tranny [message #343244 is a reply to message #343232] |
Sat, 11 May 2019 08:07 |
jhbridges
Messages: 8412 Registered: May 2011 Location: Braselton ga
Karma: -74
|
Senior Member |
|
|
Ask Jimmy the K or Manny which gasket. If they differ, use Jim's suggestion, cos he'll make it good if it leaks.
johnny
Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.
I forgive them all, save those who hurt the dogs. They must answer to me in hell
|
|
|
Re: [GMCnet] Tranny [message #343246 is a reply to message #343244] |
Sat, 11 May 2019 09:18 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
I guess that is why we have gotten to be the largest supplier of parts and
kit .
On Sat, May 11, 2019 at 6:08 AM Johnny Bridges via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Ask Jimmy the K or Manny which gasket. If they differ, use Jim's
> suggestion, cos he'll make it good if it leaks.
>
> johnny
> --
> Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons.
> Braselton, Ga.
> I forgive them all, save those who hurt the dogs. They must answer to me
> in hell
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Re: Tranny [message #343248 is a reply to message #343232] |
Sat, 11 May 2019 09:41 |
Bierman
Messages: 46 Registered: May 2017 Location: SW Florida
Karma: 0
|
Member |
|
|
Hey Jim, I bought your kit and your new pan. But I also have a couple of cork gaskets and was just wondering the best Way to go.
I also called and spoke to a rep and asked about the torque for the new pan, he told me to just tighten down snug?
Member, GMCI, Sunshine Statesman and Dixielanders
26' 1978 Eleganza II, new(rebuilt by Sirum) 403, Lenzi hubs and knuckles, front end by Ferrara
|
|
|
Re: [GMCnet] Tranny [message #343253 is a reply to message #343244] |
Sat, 11 May 2019 13:50 |
Mike Kelley
Messages: 467 Registered: February 2017
Karma: -2
|
Senior Member |
|
|
Max:
And here is why I like/use Jim Kanomata at Applied GMC in California - see attachment below - that kind of reputation is invaluable!
Mike/The Corvair a holic
Sent from my iPhone
> On May 11, 2019, at 8:07 AM, Johnny Bridges via Gmclist wrote:
>
> Ask Jimmy the K or Manny which gasket. If they differ, use Jim's suggestion, cos he'll make it good if it leaks.
>
> johnny
> --
> Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons.
> Braselton, Ga.
> I forgive them all, save those who hurt the dogs. They must answer to me in hell
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|