Ride Height control lubrication [message #343185] |
Wed, 08 May 2019 07:51 |
|
Matt Colie
Messages: 8547 Registered: March 2007 Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
NextGenGMC wrote on Wed, 08 May 2019 00:30On the topic of rear suspension... Should any parts of the ride height components be lubricated with something like WD-40 or Lithium spray? I've used my GMC few times this winter (as luck would have it - during the absolutely worst winter storms). I'm going over it and getting ready for summer. Poking around the rear wheels I wanted to make sure I'm not missing anything besides boggie pins as far as lubrication goes. I have a Quad bad setups if this helps.
Vadim,
First, I openned a new topic so this would not get lost. Topics are cheap.
Second, WD-40 is not a lubricant. So says the manufacturer and I have experience that confirms this. It may, in some cases, behave like a penetrant but that is just a happy accident. WD-40 is and was designed to be a drying agent.
Lastly, there are no external parts of the ride height control that require regular lubrication. Here, WD-40 might help, but just to reduce the corrosion of the metal parts, but it may also injure the rubber bushings in the control link, if they still exist.
Matt
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
Re: Ride Height control lubrication [message #343196 is a reply to message #343185] |
Wed, 08 May 2019 10:31 |
jhbridges
Messages: 8412 Registered: May 2011 Location: Braselton ga
Karma: -74
|
Senior Member |
|
|
I'll take a bit of exception here. The late model photocell controllers had a lube or foam or something inside them which at its current age, will glop up and cover the photocells. Disassembe and clean, and they work as well as they did new.
--johnny
Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.
I forgive them all, save those who hurt the dogs. They must answer to me in hell
|
|
|
Re: Ride Height control lubrication [message #343211 is a reply to message #343185] |
Wed, 08 May 2019 14:33 |
NextGenGMC
Messages: 146 Registered: December 2017 Location: Washington State
Karma: -1
|
Senior Member |
|
|
Matt Colie wrote on Wed, 08 May 2019 05:51NextGenGMC wrote on Wed, 08 May 2019 00:30On the topic of rear suspension... Should any parts of the ride height components be lubricated with something like WD-40 or Lithium spray? I've used my GMC few times this winter (as luck would have it - during the absolutely worst winter storms). I'm going over it and getting ready for summer. Poking around the rear wheels I wanted to make sure I'm not missing anything besides boggie pins as far as lubrication goes. I have a Quad bad setups if this helps.
Vadim,
First, I openned a new topic so this would not get lost. Topics are cheap.
Second, WD-40 is not a lubricant. So says the manufacturer and I have experience that confirms this. It may, in some cases, behave like a penetrant but that is just a happy accident. WD-40 is and was designed to be a drying agent.
Lastly, there are no external parts of the ride height control that require regular lubrication. Here, WD-40 might help, but just to reduce the corrosion of the metal parts, but it may also injure the rubber bushings in the control link, if they still exist.
Matt
Mat, Thank you for posting this a a separate topic. Your insight about possibility of damaging rubber parts on ride height controller is confirms my suspicion. It is EXACTLY the reason why I did not want to start spraying anything in sight without additional info from the collective
Vadim Jitkov
'76 Glenbrook 26'
Pullman, WA
|
|
|
Re: [GMCnet] Ride Height control lubrication [message #343218 is a reply to message #343211] |
Thu, 09 May 2019 09:47 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
There is metal to metal contact at the fasteners on the link. .
On the 78 uits the liquid is a on cures resen. WE have opened many of them.
On Wed, May 8, 2019 at 3:05 PM Vadim Jitkov via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Matt Colie wrote on Wed, 08 May 2019 05:51
>> NextGenGMC wrote on Wed, 08 May 2019 00:30
>>> On the topic of rear suspension... Should any parts of the ride
> height components be lubricated with something like WD-40 or Lithium
> spray?
>>> I've used my GMC few times this winter (as luck would have it - during
> the absolutely worst winter storms). I'm going over it and getting ready
>>> for summer. Poking around the rear wheels I wanted to make sure I'm
> not missing anything besides boggie pins as far as lubrication goes. I have
>>> a Quad bad setups if this helps.
>>
>> Vadim,
>>
>> First, I openned a new topic so this would not get lost. Topics are
> cheap.
>>
>> Second, WD-40 is not a lubricant. So says the manufacturer and I have
> experience that confirms this. It may, in some cases, behave like a
>> penetrant but that is just a happy accident. WD-40 is and was designed
> to be a drying agent.
>>
>> Lastly, there are no external parts of the ride height control that
> require regular lubrication. Here, WD-40 might help, but just to reduce the
>> corrosion of the metal parts, but it may also injure the rubber bushings
> in the control link, if they still exist.
>>
>> Matt
>
> Mat, Thank you for posting this a a separate topic. Your insight about
> possibility of damaging rubber parts on ride height controller is confirms
> my
> suspicion. It is EXACTLY the reason why I did not want to start spraying
> anything in sight without additional info from the collective :)
> --
> Vadim Jitkov
> '76 Glenbrook 26'
> Pullman, WA
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|