Re: [GMCnet] Replacing rear wheel cylinder [message #340174] |
Fri, 18 January 2019 19:43 |
BobDunahugh
Messages: 2465 Registered: October 2010 Location: Cedar Rapids, IA
Karma: 11
|
Senior Member |
|
|
You can change wheel cyl without pulling the brake shoes off. Very simple, and quick. You can't re flare the original tubing. It's too hard/brittle. It will just crack. Harbor Freight has a tubing bender that can make tight bends. You can reproduce that brake line perfectly. You MUST support the replacement line as GM did. Bob Dunahugh 78 Royale
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] Replacing rear wheel cylinder [message #340175 is a reply to message #340174] |
Fri, 18 January 2019 19:55 |
James Hupy
Messages: 6806 Registered: May 2010
Karma: -62
|
Senior Member |
|
|
You can purchase exact replacement lines, or, lines that have the same
length with the ends flared and fittings in place. With a bit of practice
and a high quality tube bender, like the one from Eastwood, or rented from
Advance Auto, you too, can make your own lines. The vice grip like tools
are made by Irwin. Ace hardware or good tool stores can get them. Not too
$$$$.
Jim Hupy
On Fri, Jan 18, 2019, 5:44 PM Bob Dunahugh You can change wheel cyl without pulling the brake shoes off. Very simple,[/color]
> and quick. You can't re flare the original tubing. It's too hard/brittle.
> It will just crack. Harbor Freight has a tubing bender that can make tight
> bends. You can reproduce that brake line perfectly. You MUST support the
> replacement line as GM did. Bob Dunahugh 78 Royale
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|
|
Re: [GMCnet] Replacing rear wheel cylinder [message #340201 is a reply to message #340193] |
Sun, 20 January 2019 00:17 |
johnd01
Messages: 354 Registered: July 2017 Location: Sacrameot
Karma: -1
|
Senior Member |
|
|
I am considering just putting it all back together. The
On Sat, Jan 19, 2019 at 4:42 PM Matt Colie wrote:
> BobDunahugh wrote on Sat, 19 January 2019 11:47
>> I had to modify those special locking plyers fitting wrench to fit
> tighter on the smallest fittings. Just took alittle grinding. Bob Dunahugh
>
> Bob,
>
> Was that the 4" size?
> I've never run into that with the littlest. I can believe the 7LW might
> not get a small line nut.
>
> Matt
> --
> Matt & Mary Colie - '73 Glacier 23 - Members GMCMI, GMCGL, GMCES
> Electronically Controlled Quiet Engine Cooling Fan
> OE Rear Drum Brakes with Applied Control Arms
> SE Michigan - Twixt A2 and Detroit
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
*John Phillips*
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Johnd01
John Phillips
Avion A2600 TZE064V101164
Rancho Cordova, CA (Sacramento)
|
|
|
Re: [GMCnet] Replacing rear wheel cylinder [message #340202 is a reply to message #340174] |
Sun, 20 January 2019 00:19 |
johnd01
Messages: 354 Registered: July 2017 Location: Sacrameot
Karma: -1
|
Senior Member |
|
|
I am considering just putting it all back together. The 7-inch version will
be here in about 10 days.
On Sat, Jan 19, 2019 at 10:17 PM John Phillips
wrote:
> I am considering just putting it all back together. The
>
> On Sat, Jan 19, 2019 at 4:42 PM Matt Colie wrote:
>
>> BobDunahugh wrote on Sat, 19 January 2019 11:47
>>> I had to modify those special locking plyers fitting wrench to fit
>> tighter on the smallest fittings. Just took alittle grinding. Bob Dunahugh
>>
>> Bob,
>>
>> Was that the 4" size?
>> I've never run into that with the littlest. I can believe the 7LW might
>> not get a small line nut.
>>
>> Matt
>> --
>> Matt & Mary Colie - '73 Glacier 23 - Members GMCMI, GMCGL, GMCES
>> Electronically Controlled Quiet Engine Cooling Fan
>> OE Rear Drum Brakes with Applied Control Arms
>> SE Michigan - Twixt A2 and Detroit
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
>
>
> --
>
> *John Phillips*
>
--
*John Phillips*
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Johnd01
John Phillips
Avion A2600 TZE064V101164
Rancho Cordova, CA (Sacramento)
|
|
|