Home » Public Forums » GMCnet » Gas Tank Switching Valve Conundrum
Gas Tank Switching Valve Conundrum [message #334366] |
Sun, 01 July 2018 19:03 |
Carl S.
Messages: 4186 Registered: January 2009 Location: Tucson, AZ.
Karma: 13
|
Senior Member |
|
|
I am in the process of re-plumbing my fuel hoses from the tanks to the front hard fuel line. Part of what I am doing is to move the lines, pumps, filters, etc to the outside of the frame at Jim Kanomata's suggestion. I am also replacing the electric fuel pump (a solenoid type pull through pump) with the GMC Net preferred Carter along with a cartridge type filter and a new tank selector valve.
My plan is (was?) to run the new fuel pump off of the auxiliary tank only, like I had my old one set up. The problem is that the tank selector valve says to NOT pressurize the inlets. The only way I can think of to run it that way is to pressurize the inlet to the valve by putting the pump between the tank and the valve. Since there are two inlets on the valve and only one outlet, I can't think of any other way to do it besides running the electric pump all the time.
The old set-up I have had on the coach for years puts pressure on the inlet side of the valve, on the aux inlet, and it has worked fine. Can anybody give me a reason this will not continue to work as it has in the past? Is there a danger to "pressurizing the inlet" or any reason I shouldn't do it, other than the obvious, the warning on the instructions.
I'm already two thirds of the way through this project and don't want to have to start again.
Thanks
Carl Stouffer
'75 ex Palm Beach
Tucson, AZ.
Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive, Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American Eagles, Solar battery charging. GMCSJ and GMCMI member
|
|
|
Re: [GMCnet] Gas Tank Switching Valve Conundrum [message #334373 is a reply to message #334366] |
Sun, 01 July 2018 19:37 |
Ken Henderson
Messages: 8726 Registered: March 2004 Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
Carl,
Since you've got instructions saying to not pressurize the inlet, I presume
you've bought a new selector valve?
If you have NOT bought that valve, I strongly suggest comparing the cost of
a new one (which is certainly advisable in view of the number of failures
seen lately) to the cost of a second electric pump. The difference is
probably not great and the advantages of having redundant electric pumps
should be more than worth that cost.
You've probably read this diatribe of mine too many times, but I keep
hoping to help some newby by repeating it: An electric pump from each
tank, selected with the dash's tank selector switch, tee'd together into
the existing forward fuel line is the most reliable system possible because
of its redundancy. The mechanical pump should be bypassed to ensure that
it doesn't leak the pressurized fuel into the crankcase. Aside from
incorporating a "surge tank" with a return line to the fuel tanks, this is
probably the most effective vapor lock preventive system available (without
a much more complex fuel cooling system).
JMHO,
Ken H.
On Sun, Jul 1, 2018 at 8:03 PM Carl Stouffer wrote:
> I am in the process of re-plumbing my fuel hoses from the tanks to the
> front hard fuel line. Part of what I am doing is to move the lines, pumps,
> filters, etc to the outside of the frame at Jim Kanomata's suggestion. I
> am also replacing the electric fuel pump (a solenoid type pull through pump)
> with the GMC Net preferred Carter along with a cartridge type filter and a
> new tank selector valve.
>
> My plan is (was?) to run the new fuel pump off of the auxiliary tank only,
> like I had my old one set up. The problem is that the tank selector valve
> says to NOT pressurize the inlets. The only way I can think of to run it
> that way is to pressurize the inlet to the valve by putting the pump between
> the tank and the valve. Since there are two inlets on the valve and only
> one outlet, I can't think of any other way to do it besides running the
> electric pump all the time.
>
> The old set-up I have had on the coach for years puts pressure on the
> inlet side of the valve, on the aux inlet, and it has worked fine. Can
> anybody
> give me a reason this will not continue to work as it has in the past? Is
> there a danger to "pressurizing the inlet" or any reason I shouldn't do it,
> other than the obvious, the warning on the instructions.
>
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
Re: [GMCnet] Gas Tank Switching Valve Conundrum [message #334377 is a reply to message #334373] |
Sun, 01 July 2018 20:20 |
Carl S.
Messages: 4186 Registered: January 2009 Location: Tucson, AZ.
Karma: 13
|
Senior Member |
|
|
Thanks Ken,
Yes, I did buy a new selector valve from Applied, along with all the other components. Your advice is well taken, and that is probably what I should do.
However, I probably won't At least not this time around. The new valve is identical to the old one, which worked perfectly upon testing it on a battery. I only replaced it (again) because it has been recommended here ans elsewhere. I had the old pump, which proved to not be up to the task, before the valve and it never presented a problem.
I guess I could return the new valve and buy another pump. Do you have a wiring diagram for the set-up you are advocating?
Carl Stouffer
'75 ex Palm Beach
Tucson, AZ.
Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive, Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American Eagles, Solar battery charging. GMCSJ and GMCMI member
|
|
|
|
Re: [GMCnet] Gas Tank Switching Valve Conundrum [message #334383 is a reply to message #334380] |
Sun, 01 July 2018 20:45 |
Carl S.
Messages: 4186 Registered: January 2009 Location: Tucson, AZ.
Karma: 13
|
Senior Member |
|
|
Ken Burton wrote on Sun, 01 July 2018 18:26Lots of people have been pressurizing those at carb pressures (5 PSI) on GMCs with no problems.
I'm one of them. I replaced a bad switching valve early on and added a pump between the tank and the valve later, not ever seeing that warning before. It just made me a little concerned.
I also have a brand new (also Carter) mechanical pump on my brand new engine, so I'm not really worried about a diaphragm rupture pumping gas into my crankcase.
Carl Stouffer
'75 ex Palm Beach
Tucson, AZ.
Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive, Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American Eagles, Solar battery charging. GMCSJ and GMCMI member
|
|
|
Re: [GMCnet] Gas Tank Switching Valve Conundrum [message #334395 is a reply to message #334377] |
Sun, 01 July 2018 22:17 |
|
USAussie
Messages: 15912 Registered: July 2007 Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
Carl,
If I were you I'd "I guess I could return the new valve and buy another pump."
Regards,
Rob M.
The Pedantic Mechanic
Sydney, Australia
AUS '75 Avion - The Blue Streak TZE365V100428
USA '75 Avion - Double Trouble TZE365V100426
USA '77 Kingsley - TZE 267V100808
-----Original Message-----
From: Gmclist [mailto:gmclist-bounces@list.gmcnet.org] On Behalf Of Carl Stouffer
Sent: Sunday, July 1, 2018 8:20 PM
To: gmclist@list.gmcnet.org
Subject: Re: [GMCnet] Gas Tank Switching Valve Conundrum
Thanks Ken,
Yes, I did buy a new selector valve from Applied, along with all the other components. Your advice is well taken, and that is
probably what I should do.
However, I probably won't :roll: At least not this time around. The new valve is identical to the old one, which worked
perfectly upon testing it on a battery. I only replaced it (again) because it has been recommended here ans elsewhere. I had the
old pump, which proved to not be up to the task, before the valve and it never presented a problem.
I guess I could return the new valve and buy another pump. Do you have a wiring diagram for the set-up you are advocating?
--
Carl Stouffer
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
|
|
Re: Gas Tank Switching Valve Conundrum [message #334415 is a reply to message #334366] |
Mon, 02 July 2018 07:49 |
jhbridges
Messages: 8412 Registered: May 2011 Location: Braselton ga
Karma: -74
|
Senior Member |
|
|
Here's what that setup looks like, using Mr. Gasket pumps which have built - in check valves and Wix filters on the pump inputs:
http://www.gmcmhphotos.com/photos/g6198-cane-9-creek-rv-park-heflin-2c-al.html
I pulled the input lines off the selector and rputed them uncut to the pump inputs; and pulled the output line and routed it uncut to the tee on the pumps' output and capped the selector to keep dirt and crud out of it. The fuel line fitting where the hard line to the carb used to fit the mechanical pump is a standard which means the hard line is unchanged. Result: You can convert back to OEM in thirty minutes beside the road if you had to. 25 of which would be replacing the mechanical pump.
--johnny
Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.
I forgive them all, save those who hurt the dogs. They must answer to me in hell
|
|
|
Goto Forum:
Current Time: Sun Sep 29 12:31:22 CDT 2024
Total time taken to generate the page: 0.00675 seconds
|