Oil cooler Line Leak [message #333607] |
Sun, 17 June 2018 15:21 |
Justin Brady
Messages: 769 Registered: April 2015 Location: Bell Buckle, TN
Karma: 11
|
Senior Member |
|
|
So after a deep deep cleaning and covering the front of the engine in baby powder I believe I've finally found the source of my oil leak.
I believe it's the fitting between the hard line and the flex lines for the oil cooler.
Are there any O-rings or is that just a compression fitting?
Where they sit there's no way for me to get them any tighter, I just can't get the leverage on the wrenches to get any tighter than they already are.
Does anyone make full replacement lines from the oil filter adapter to the radiator? preferably without the extra fittings in the middle (the ones that are leaking)
Justin Brady
http://www.thegmcrv.com/
1976 Palm Beach 455
|
|
|
|
|
Re: [GMCnet] Oil cooler Line Leak [message #333610 is a reply to message #333609] |
Sun, 17 June 2018 16:43 |
James Hupy
Messages: 6806 Registered: May 2010
Karma: -62
|
Senior Member |
|
|
J.R.'s are first rate. And they route a bit differently than stock. I think
for the better. But, opinions vary.
Jim Hupy
Salem, Or
78 GMC ROYALE 403
On Sun, Jun 17, 2018, 2:16 PM Richard Denney wrote:
> JR Slaten makes them, in stainless with aircraft hose.
>
> JimK has them, of course.
>
> http://www.appliedgmc.com/prod.itml/icOid/587
>
> Rick “these are done right” Denney
>
> On Sun, Jun 17, 2018 at 4:22 PM Justin Brady wrote:
>
>> So after a deep deep cleaning and covering the front of the engine in
> baby
>> powder I believe I've finally found the source of my oil leak.
>> I believe it's the fitting between the hard line and the flex lines for
>> the oil cooler.
>> Are there any O-rings or is that just a compression fitting?
>>
>> Where they sit there's no way for me to get them any tighter, I just
> can't
>> get the leverage on the wrenches to get any tighter than they already
> are.
>>
>>
>> Does anyone make full replacement lines from the oil filter adapter to
> the
>> radiator? preferably without the extra fittings in the middle (the ones
>> that are leaking)
>> --
>> Justin Brady
>> http://www.thegmcrv.com/
>> 1976 Palm Beach 455
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
> --
> Rick Denney
> 73 x-Glacier 230 "Jaws"
> Off-list email to rick at rickdenney dot com
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] Oil cooler Line Leak [message #333611 is a reply to message #333610] |
Sun, 17 June 2018 16:53 |
tphipps
Messages: 3005 Registered: August 2004 Location: Spanish Fort, AL
Karma: 9
|
Senior Member |
|
|
J.R's are first rate and unbreakable. Guaranteed forever. Just be sure you get the right one for your block. 403 & 455 are different. Also, the oil filter adapter is different for each engine.
Tom
2012 Phoenix Cruiser model 2552
KA4CSG
|
|
|
|
|
|
|
Re: [GMCnet] Oil cooler Line Leak [message #333629 is a reply to message #333626] |
Sun, 17 June 2018 21:01 |
Ken Burton
Messages: 10030 Registered: January 2004 Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
Justin Brady wrote on Sun, 17 June 2018 20:44Agreed 100%
I'd just rather have a single length of flexible line if possible
The JR stainless flexible lines for the GMC with 403 engine are single piece flexible from the oil filter adapter on the engine all the way to the radiator oil cooler.
Just order 403 ones from JR or Jim K.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
Re: [GMCnet] Oil cooler Line Leak [message #333630 is a reply to message #333626] |
Sun, 17 June 2018 21:01 |
Ken Burton
Messages: 10030 Registered: January 2004 Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
Justin Brady wrote on Sun, 17 June 2018 20:44Agreed 100%
I'd just rather have a single length of flexible line if possible
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
|
Re: [GMCnet] Oil cooler Line Leak [message #333642 is a reply to message #333635] |
Mon, 18 June 2018 00:07 |
roy1
Messages: 2126 Registered: July 2004 Location: Minden nevada
Karma: 6
|
Senior Member |
|
|
You may be able to get by with a couple of copper flair washers between the hard steel lines and the flex lines. You are using stainless Teflon lines and not the original fabric lines? If not you need to get JR's lines.
Roy Keen
Minden,NV
76 X Glenbrook
|
|
|