|
|
Re: [GMCnet] steering locked not key [message #328795 is a reply to message #328792] |
Sat, 03 February 2018 13:00 |
sgltrac
Messages: 2797 Registered: April 2011
Karma: 1
|
Senior Member |
|
|
Steering wheel that is.
On Sat, Feb 3, 2018 at 10:59 AM Todd Sullivan wrote:
> Turn the wheel hard against the stop. Try to “bounce” the wheel back and
> forth while wiggling the key.
>
> Sully
> 77 eleganza 2
> Bellevue.
>
> On Sat, Feb 3, 2018 at 10:36 AM Burt and Faye curtis curtisunlimitedbandf@gmail.com> wrote:
>
>> O have Gene Fisher up here and solved non start problem. However turned
>> wheels all the way to right to acess battery and shut off engine. Now
>> can't
>> start again as column is locked. Any suggestions? Have wheels off ground.
>>
>> Thanks,
>>
>>
>> Fay
>> 76 Glenbrook
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Sully
77 Royale basket case.
Future motorhome land speed record holder(bucket list)
Seattle, Wa.
|
|
|
|
|
|
|
Re: [GMCnet] steering locked not key [message #328812 is a reply to message #328792] |
Sat, 03 February 2018 18:46 |
|
Matt Colie
Messages: 8547 Registered: March 2007 Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
Faye,
If you take off the horn button, it will not get you very far. You would have to take off the steering wheel, remove the turn signal switch and then have the lock plate removing tool (you can often borrow at a parts store) to get the steering column lock plate loose. And that may not want to come loose with load on it. But it cold probably be convinced to do so with little collateral damage.
If Jim's straighten the tilt or straighten the column and Sully's shake the wheel don't get it, have a gorilla (that big guy that will almost anything for a beer) try to turn farther the way the wheels are now. That may unload the lock enough to move it.
The wheels are off the ground, so the load is all in the steering gear and not the tires. But, if enough parts have been replaced and not quite right, then the stop load in the steering could be high because it is also against the knuckle stops. Strangely, this may just get to be less if the tires are back on the ground and the tie-rods can unload the system. I used to have all kinds of trouble like this before I got things phased correctly. Right now, you really need Alex or Chuck looking in.
If you get really desperate, I have two ideas (that I will review the relative merit off) that might help.
One try you might do is would be to remove the pinch bolt from the CV joint at the bottom of the column and tap the CV joint off the the actual steering shaft. If you are locked against the stop in the steering box, the spline may need some dressing with a file to go back on. My 73 has enough travel in the sliding coupler to do this.
The other would be to loosen the four bolts that hold the steering box to the left frame rail. This could only be a monumental PITA, but it would have the advantage of zero collateral damage. This will work on a GMC only because of the CV-Slip-UJoint that is there so the steering box can go any way it needs to. You shouldn't need to take the bolts out and don't. You have to know how heavy that puppy is and all it needs is to give you some slack.
Good Luck
Matt
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
|
Re: [GMCnet] steering locked not key [message #328815 is a reply to message #328813] |
Sat, 03 February 2018 20:12 |
Mr ERFisher
Messages: 7117 Registered: August 2005
Karma: 2
|
Senior Member |
|
|
Yahoooo tanks everyone we going on thanks for all your help bye now
On Sat, Feb 3, 2018 at 5:08 PM Burt and Faye curtis <
curtisunlimitedbandf@gmail.com> wrote:
>>
>> First a thank you to everyone for the ideas, but fixed it with help from
>> Ken Burton and Chuck Boyd. Had to remove the steering wheel - easy enough
>> once got the right tools and bolts that weren't bent or stripped, then
> the
>> plastic cover. This exposed the locking pin that was entrenched. A few
>> smart blows ( technical term I learned from Bert) and in popped out,
> which
>> allowed the key to turn. One benifit, now my steering wheel is spot on,
> not
>> one or two degrees of center.
>
> There was no gorilla big enough to make that wheel turn without something
> breaking.
> Thanks again,
>
> Fay Curtis
> 76 Glenbrook
>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Gene Fisher -- 74-23,77PB/ore/ca
“Give a man a fish; you have fed him for today --- give him a URL and
-------
http://gmcmotorhome.info/
Alternator Protection Cable
http://gmcmotorhome.info/APC.html
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|