| [GMCnet] Power steering pulley removal [message #308922] |
Mon, 17 October 2016 18:26  |
Advanced Concept Ener
Messages: 112
Registered: December 2014
Karma: 0
|
Senior Member |
|
|
No luck yet!
On page 9-2 figure 1 of x-7725 it shows a nut on the shaft. Pretty confusing. I put split puller on indent of pulley hub and tightened down as hard as I can. Hit shaft of puller with hammer. All I did was round out the Allen wrench fitting and started to bend metal around hole where I stuck a wrench to stop shaft from rotating. No movement at all. I guess I can put. A socket on the puller shaft tomorrow and use the impact wrench. Hardened shaft will either splinter, totally ruin the nut ?? Or get the pulley to pop off. Does anyone know where I can buy replacement pulley as I may need it?
Jon Darcy ACES
North Jersey 76 stretch, flares, 4 bag, Alcoa's, bunkhouse,MAC Dash,Manny Trans, FiTech FI,Honda 6010
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|
| Re: [GMCnet] Power steering pulley removal [message #308928 is a reply to message #308922] |
Mon, 17 October 2016 18:53  |
 |
USAussie
Messages: 15912
Registered: July 2007
Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
Jon,
Look at the next page 9-3.
Figure 3 - Pulley Removal - Special Tool J-25034
Figure 4 - Pulley Installation - Special tool J-25033
Regards,
Rob M.
USAussie - Downunder
AUS '75 Avion - The Blue Streak TZE365V100428
USA '75 Avion - Double Trouble TZE365V100426
-----Original Message-----
From: Gmclist [mailto:gmclist-bounces@list.gmcnet.org] On Behalf Of Advanced Concept Energy Solutions
Sent: Tuesday, October 18, 2016 10:27 AM
To: gmclist@list.gmcnet.org
Subject: [GMCnet] Power steering pulley removal
No luck yet!
On page 9-2 figure 1 of x-7725 it shows a nut on the shaft. Pretty confusing. I put split puller on indent of pulley hub and
tightened down as hard as I can. Hit shaft of puller with hammer. All I did was round out the Allen wrench fitting and started to
bend metal around hole where I stuck a wrench to stop shaft from rotating. No movement at all. I guess I can put. A socket on the
puller shaft tomorrow and use the impact wrench. Hardened shaft will either splinter, totally ruin the nut ?? Or get the pulley to
pop off. Does anyone know where I can buy replacement pulley as I may need it?
Jon Darcy ACES
North Jersey 76 stretch, flares, 4 bag, Alcoa's, bunkhouse,MAC Dash,Manny Trans, FiTech FI,Honda 6010
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
|
| Re: [GMCnet] Power steering pulley removal [message #308931 is a reply to message #308928] |
Mon, 17 October 2016 19:18 |
Bruce Hart
Messages: 1501
Registered: October 2011
Location: La Grange, Wyoming
Karma: 5
|
Senior Member |
|
|
Jon,
Youtube is your friend;-)
https://www.youtube.com/watch?v=QZrH4Xajy9I
On Mon, Oct 17, 2016 at 5:53 PM, Rob Mueller
wrote:
> Jon,
>
> Look at the next page 9-3.
>
> Figure 3 - Pulley Removal - Special Tool J-25034
>
> Figure 4 - Pulley Installation - Special tool J-25033
>
> Regards,
> Rob M.
> USAussie - Downunder
> AUS '75 Avion - The Blue Streak TZE365V100428
> USA '75 Avion - Double Trouble TZE365V100426
>
>
> -----Original Message-----
> From: Gmclist [mailto:gmclist-bounces@list.gmcnet.org] On Behalf Of
> Advanced Concept Energy Solutions
> Sent: Tuesday, October 18, 2016 10:27 AM
> To: gmclist@list.gmcnet.org
> Subject: [GMCnet] Power steering pulley removal
>
> No luck yet!
> On page 9-2 figure 1 of x-7725 it shows a nut on the shaft. Pretty
> confusing. I put split puller on indent of pulley hub and
> tightened down as hard as I can. Hit shaft of puller with hammer. All I
> did was round out the Allen wrench fitting and started to
> bend metal around hole where I stuck a wrench to stop shaft from rotating.
> No movement at all. I guess I can put. A socket on the
> puller shaft tomorrow and use the impact wrench. Hardened shaft will
> either splinter, totally ruin the nut ?? Or get the pulley to
> pop off. Does anyone know where I can buy replacement pulley as I may need
> it?
> Jon Darcy ACES
> North Jersey 76 stretch, flares, 4 bag, Alcoa's, bunkhouse,MAC Dash,Manny
> Trans, FiTech FI,Honda 6010
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Bruce Hart
1976 Palm Beach
Milliken, Co
GMC=Got More Class
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Bruce Hart
1976 Palm Beach
1977 28' Kingsley
La Grange, Wyoming
|
|
|
|
GMCforum
Search
Help
Register
Login
Home
