[GMCnet] Back window leak and kitchen exhaust/ lights [message #299151] |
Sat, 16 April 2016 18:02 |
JT O'Neill
Messages: 7 Registered: April 2015
Karma: 0
|
Junior Member |
|
|
Howdy everyone.
I’ve got a 75 Glenbrook. 2 things I need to fix asap,, appreciate any ideas on either or both-
#1- major leak above the big back window- no leak one day, next day tons of water dripping down, appears to be in the center along the top, but not sure exactly where. I’m thinking of getting black caulk and applying on the black line that’s ABOVE the window framing (just below where all the paint is chipped away in the first 2 pictures here- http://www.cbabc.com/gmc/index.html
question- should I remove the existing caulking/ plastic, or put it on top of existing?
#2- kitchen lights/ exhaust fan became unattached on the side nearest the wall- best way to fix? pictures are #3 and 4 at the same website - http://www.cbabc.com/gmc/index.html
Thanks!
JT O’Neill
South Beach, OR
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|
|
Re: [GMCnet] Back window leak and kitchen exhaust/ lights [message #299288 is a reply to message #299151] |
Tue, 19 April 2016 18:38 |
Ken Burton
Messages: 10030 Registered: January 2004 Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
About 15 years ago when I got my coach I had the same leak. I measured the length across the top and down the sides I got one continuous piece of vacuum hose just slightly larger across than the gap in that seam. I started in the top center and worked across and down the sides, one side at a time. I pulled and stretched the hose as I installed it to make it slightly thinner as I filled the seam. Over time the hose will retract and fill any regularities in the width of the seam. I did not bother with sealing the bottom. The whole project took about 20 minutes to install.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
Re: [GMCnet] Back window leak and kitchen exhaust/ lights [message #299289 is a reply to message #299288] |
Tue, 19 April 2016 18:46 |
James Hupy
Messages: 6806 Registered: May 2010
Karma: -62
|
Senior Member |
|
|
The hose trick works well. I use 1/2" O.D. Foam backer rod. It can be
forced into the gap with a dull putty knife while pulling a slight stretch
on the rod. No sealer is used. It really works well.
Jim Hupy
Salem, Or
78 GMC ROYALE 403
On Apr 19, 2016 4:39 PM, "Ken Burton" wrote:
> About 15 years ago when I got my coach I had the same leak. I measured
> the length across the top and down the sides I got one continuous piece of
> vacuum hose just slightly larger across than the gap in that seam. I
> started in the top center and worked across and down the sides, one side at
> a
> time. I pulled and stretched the hose as I installed it to make it
> slightly thinner as I filled the seam. Over time the hose will retract and
> fill
> any regularities in the width of the seam. I did not bother with sealing
> the bottom. The whole project took about 20 minutes to install.
> --
> Ken Burton - N9KB
> 76 Palm Beach
> Hebron, Indiana
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|