| Installation instructions for a Mac NGMC-2010 dash [message #296210] |
Thu, 25 February 2016 21:09  |
gibsongo
Messages: 116
Registered: October 2012
Location: Montreal West, Quebec, Ca...
Karma: 0
|
Senior Member |
|
|
Hello all,
Just trying my luck here. I recently bought a Custom Instruments Panel NGMC-2010 dash (a MAC dash) from a third party - it was advertised on the GMC facebook site. The dash looks brand new, and comes with a box of adaptors, sensors, etc. but no installation instructions. I trolled the net and found that someone had posted a MAC owners manual - complete with instructions - but it's for another model.
Just checking here to see whether anyone else who installed this model MAC dash had their manual handy and could possible send me a scan. I suppose I can always check with Custom Instruments Panel, but worry that they might be not want to since I bought the dash from a third party rather than directly from them.
Thanks in advance
Gordon
1976 23" Norris Upfit
Montreal West, Quebec, Canada
Gordon Gibson
1976 23" Norris Upfit
Montreal West, Quebec, Canada
|
|
|
|
| Re: [GMCnet] Installation instructions for a Mac NGMC-2010 dash [message #296212 is a reply to message #296210] |
Thu, 25 February 2016 21:14  |
George Zhookoff
Messages: 398
Registered: December 2004
Location: Snellville, GA
Karma: 6
|
Senior Member |
|
|
Mac is one of the good guys. Call him and ask. You might even offer to buy it?
George "with the Mac Daddy installed" Zhookoff
78 EL II
Atlanta
> On Feb 25, 2016, at 10:11 PM, "Gordon Gibson" wrote:
>
> Hello all,
>
> Just trying my luck here. I recently bought a Custom Instruments Panel NGMC-2010 dash (a MAC dash) from a third party - it was advertised on the GMC
> facebook site. The dash looks brand new, and comes with a box of adaptors, sensors, etc. but no installation instructions. I trolled the net and found
> that someone had posted a MAC owners manual - complete with instructions - but it's for another model.
>
> Just checking here to see whether anyone else who installed this model MAC dash had their manual handy and could possible send me a scan. I suppose I
> can always check with Custom Instruments Panel, but worry that they might be not want to since I bought the dash from a third party rather than
> directly from them.
>
> Thanks in advance
>
> Gordon
> 1976 23" Norris Upfit
> Montreal West, Quebec, Canada
> --
> 1976 23" Norris Upfit
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|
| Re: [GMCnet] Installation instructions for a Mac NGMC-2010 dash [message #296214 is a reply to message #296212] |
Thu, 25 February 2016 21:45 |
gibsongo
Messages: 116
Registered: October 2012
Location: Montreal West, Quebec, Ca...
Karma: 0
|
Senior Member |
|
|
Thanks George, I'll certainly give it a try. Besides, I am going to need a panel for the load leveling valves and perhaps a custom-made Lights/Wipers/Battery Boost/Fuel Tank Selector panel since I am converting to electric wipers and the kit has two rotary switches rather than one up and down switch and one momentary on switch. Perhaps this would be "motivation" to supply the manual.
Regards
Gordon
Gordon Gibson
1976 23" Norris Upfit
Montreal West, Quebec, Canada
|
|
|
|
| Re: [GMCnet] Installation instructions for a Mac NGMC-2010 dash [message #296248 is a reply to message #296210] |
Fri, 26 February 2016 15:01 |
Rob
Messages: 651
Registered: November 2013
Location: Victoria, BC
Karma: 3
|
Senior Member |
|
|
Is this the manual you need?:
http://www.bdub.net/manuals/McNeal_Dash_Owners_Manual.pdf
Rob
Victoria, BC
76 Royale - Rear Twins/Dry Bath
On 2016-02-25, at 7:09 PM, Gordon Gibson wrote:
> Hello all,
>
> Just trying my luck here. I recently bought a Custom Instruments Panel NGMC-2010 dash (a MAC dash) from a third party - it was advertised on the GMC
> facebook site. The dash looks brand new, and comes with a box of adaptors, sensors, etc. but no installation instructions. I trolled the net and found
> that someone had posted a MAC owners manual - complete with instructions - but it's for another model.
>
> Just checking here to see whether anyone else who installed this model MAC dash had their manual handy and could possible send me a scan. I suppose I
> can always check with Custom Instruments Panel, but worry that they might be not want to since I bought the dash from a third party rather than
> directly from them.
>
> Thanks in advance
>
> Gordon
> 1976 23" Norris Upfit
> Montreal West, Quebec, Canada
> --
> 1976 23" Norris Upfit
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Rob -
Victoria, BC -
76 Royale - Rear Twins/Dry Bath
|
|
|
|
| Re: Installation instructions for a Mac NGMC-2010 dash [message #296321 is a reply to message #296210] |
Sat, 27 February 2016 19:00 |
gibsongo
Messages: 116
Registered: October 2012
Location: Montreal West, Quebec, Ca...
Karma: 0
|
Senior Member |
|
|
Thanks Rob.
I had found this one thanks to the miracle of Google, but it's for a CIP-2626/G model, whereas mine is a NGMC-2010 model - different enough that the process would be very different. I am not doing the actual installation, and the mechanic who is wanted the manual to be able to estimate the amount of time involved. I have contacted Custom Instrument Panels and hopefully will be able to get the appropriate manual from them.
Gordon
Gordon Gibson
1976 23" Norris Upfit
Montreal West, Quebec, Canada
|
|
|
|
GMCforum
Search
Help
Register
Login
Home
