Dodge Steel Wheel [message #295007] |
Wed, 03 February 2016 21:17 |
erichb
Messages: 22 Registered: February 2013
Karma: 0
|
Junior Member |
|
|
I know alum wheels from the late 90s dodge 2500/3500 fit and widen stance, but will Steel from same vintage also work.
I ask because I believe the steel are a 7" wheel width and give more tire options
thanks
73 Canyonlands, Fresh TH425 and FD, Bags and Pins updated. Needs A/C, Top and Front service....Minneapolis
|
|
|
Re: Dodge Steel Wheel [message #295027 is a reply to message #295007] |
Thu, 04 February 2016 09:10 |
tphipps
Messages: 3005 Registered: August 2004 Location: Spanish Fort, AL
Karma: 9
|
Senior Member |
|
|
They would not be hub centered. The lug nuts and studs would be doing all the work. May have trouble getting the rims in the center of the wheel.
Wider rims may cause clearance problems for the rear 4 wheels, especially on the 73 and early 74 models.
Just my take, based on many earlier discussions on the net. Late model GMC/Chevy Dually Steel rims will also not fit on the front of the GMC, unless you also use the available spacers. They will work on the rear 4 wheels.
Tom, MS II
2012 Phoenix Cruiser model 2552
KA4CSG
|
|
|
Re: Dodge Steel Wheel [message #295038 is a reply to message #295007] |
Thu, 04 February 2016 11:54 |
Carl S.
Messages: 4186 Registered: January 2009 Location: Tucson, AZ.
Karma: 13
|
Senior Member |
|
|
erichb wrote on Wed, 03 February 2016 20:17I know alum wheels from the late 90s dodge 2500/3500 fit and widen stance, but will Steel from same vintage also work.
I ask because I believe the steel are a 7" wheel width and give more tire options
thanks
I can't say with certainty that the steel wheels will fit, but I don't see why not. I have been running the alloy, 16" X 8" Dodge Truck rims on the front (only) for about six years and over 20,000 miles now with NO issues. The fact that they are lug centered does not seem to be a problem at all. The alloy wheels fit around the 80mm calipers, steel wheels are an unknown in that regard.
I don't think they would work well on the rear positions due to the different offset. But, on the front, as long as the inside of the rim clears the brake assembly, they should fit.
Carl Stouffer
'75 ex Palm Beach
Tucson, AZ.
Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive, Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American Eagles, Solar battery charging. GMCSJ and GMCMI member
|
|
|
Re: Dodge Steel Wheel [message #295049 is a reply to message #295038] |
Thu, 04 February 2016 15:13 |
Bob de Kruyff
Messages: 4260 Registered: January 2004 Location: Chandler, AZ
Karma: 1
|
Senior Member |
|
|
Carl S. wrote on Thu, 04 February 2016 10:54erichb wrote on Wed, 03 February 2016 20:17I know alum wheels from the late 90s dodge 2500/3500 fit and widen stance, but will Steel from same vintage also work.
I ask because I believe the steel are a 7" wheel width and give more tire options
thanks
I can't say with certainty that the steel wheels will fit, but I don't see why not. I have been running the alloy, 16" X 8" Dodge Truck rims on the front (only) for about six years and over 20,000 miles now with NO issues. The fact that they are lug centered does not seem to be a problem at all. The alloy wheels fit around the 80mm calipers, steel wheels are an unknown in that regard.
I don't think they would work well on the rear positions due to the different offset. But, on the front, as long as the inside of the rim clears the brake assembly, they should fit.
I'm sure this has been discussed many times, but if you use tapered lug nuts I don't see any need for hub centering. I also feel that with hub centering, non tapered lug nuts with washers are also fine.
Bob de Kruyff
78 Eleganza
Chandler, AZ
|
|
|
Re: Dodge Steel Wheel [message #295063 is a reply to message #295007] |
Thu, 04 February 2016 18:27 |
Adrien G.
Messages: 474 Registered: May 2008 Location: Burns Flat, OK 73624
Karma: 1
|
Senior Member |
|
|
Erich,
The Dodge Steel 16x6 (with dome center)do fit front and rear. The alum rims do bolt on to the rear hubs, but the width and offset makes then not usable.
I'm using Dodge steel rims with a spacer ring to make them hub center. Over the rims I'm using a tension (reinforcing) ring with tapered
lug nuts, the tension (reinforcing)ring is 1/4 thick x 4.567 id x 8-1/4 od with tapered bolt holes. From Chevy/GMC 1 ton duallys.
Pic of what they look like below.
http://www.millertire.com/products/wheels/parts/reinforcing-rings/8-hole-wheel-reinforcing-ring/
Because of the ID of the tension ring (4.567), the centering spacer can't work its way out of location.
Used rims need to be checked on a lathe or tire-balancer (or ?) for run out.
You can't use taper nuts to bolt center on The Dodge rims, the holes are made for flanged nuts.
Weather that's good enough to center, I can't say.
You need to fill in your signature file with name, location, and your coach info to help use help you better.
Adrien & Jenny Genesoto
75 Glenbrook (26-3) Mods LS3.70 FD / Reaction Sys / 80mm Front&Intermidiate / Hydroboost / 16" Tires / Frame Rebuild / Interior Rebuild
Yuba City,Ca. Text 530-nine-3-three-3-nine-nine-6
|
|
|
Re: Dodge Steel Wheel [message #295101 is a reply to message #295049] |
Fri, 05 February 2016 11:11 |
erichb
Messages: 22 Registered: February 2013
Karma: 0
|
Junior Member |
|
|
Thanks, i think i will have to find a set and dry fit before adding tires. Good catch on the 80mm. I do have those. What size tire you run on the 8" width
73 Canyonlands, Fresh TH425 and FD, Bags and Pins updated. Needs A/C, Top and Front service....Minneapolis
|
|
|
Re: Dodge Steel Wheel [message #295113 is a reply to message #295101] |
Fri, 05 February 2016 12:48 |
Carl S.
Messages: 4186 Registered: January 2009 Location: Tucson, AZ.
Karma: 13
|
Senior Member |
|
|
erichb wrote on Fri, 05 February 2016 10:11Thanks, i think i will have to find a set and dry fit before adding tires. Good catch on the 80mm. I do have those. What size tire you run on the 8" width
I have been running a 255/70R16 tire (BFG All Terrain). It is wider and only slightly taller than the 225/75s on the rear. Next time I replace the front tires I will probably go with a 245/70R16 Cooper that was not available last time I needed front tires. Jon Roche runs these on his 16 X 8 Dodge rims.
Carl Stouffer
'75 ex Palm Beach
Tucson, AZ.
Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive, Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American Eagles, Solar battery charging. GMCSJ and GMCMI member
|
|
|
Re: Dodge Steel Wheel [message #295174 is a reply to message #295063] |
Sat, 06 February 2016 13:16 |
erichb
Messages: 22 Registered: February 2013
Karma: 0
|
Junior Member |
|
|
sent you PM, a little wordy..sorry
73 Canyonlands, Fresh TH425 and FD, Bags and Pins updated. Needs A/C, Top and Front service....Minneapolis
|
|
|
Re: Dodge Steel Wheel [message #295176 is a reply to message #295174] |
Sat, 06 February 2016 13:47 |
Adrien G.
Messages: 474 Registered: May 2008 Location: Burns Flat, OK 73624
Karma: 1
|
Senior Member |
|
|
Erich, check PM.
Adrien & Jenny Genesoto
75 Glenbrook (26-3) Mods LS3.70 FD / Reaction Sys / 80mm Front&Intermidiate / Hydroboost / 16" Tires / Frame Rebuild / Interior Rebuild
Yuba City,Ca. Text 530-nine-3-three-3-nine-nine-6
|
|
|