GMCforum: GMCnet » [GMCnet] Greaseless GMC Front Bearings?

Home » Public Forums » GMCnet » [GMCnet] Greaseless GMC Front Bearings?

Show: Today's Messages :: Polls :: Message Navigator

[GMCnet] Greaseless GMC Front Bearings? [message #278090]

Wed, 20 May 2015 17:58

Ken Henderson

Messages: 8726
Registered: March 2004
Location: Americus, GA

Karma: 9

Senior Member

http://www.popularmechanics.com/technology/gear/a15603/super-efficient-greaseless-bearings/

MAYBE. But sounds to me like they'll be noisy.

Ken H.
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach

Report message to a moderator

Re: [GMCnet] Greaseless GMC Front Bearings? [message #278093 is a reply to message #278090]

Wed, 20 May 2015 19:06

rickmike

Messages: 252
Registered: September 2011
Location: United States

Karma: 0

Senior Member

I am not sure that they would be any noisier but I suspect that the load capacity could be reduced if the contact area is less on the race modification.

Rick M.

1974 26' Canyonlands aka "The General" Clinton, TN

Report message to a moderator

Re: [GMCnet] Greaseless GMC Front Bearings? [message #278112 is a reply to message #278090]

Wed, 20 May 2015 22:38

Bullitthead

Messages: 1411
Registered: November 2013

Karma: 5

Senior Member

Yeah, I'd like to see the results on a LOADED bearing. If this is viable under load, you have to wonder why bearings with pitted races don't last much longer after they become pitted. Maybe because the balls get distorted when the races get holy, but I've seen plenty of pitted races with shiny smooth balls or rollers, and they made PLENTY of noise when they were loaded!

Terry Kelpien ASE Master Technician 73 Glacier 260 Smithfield, Va.

Report message to a moderator

Re: [GMCnet] Greaseless GMC Front Bearings? [message #278136 is a reply to message #278112]

Thu, 21 May 2015 09:12

Keith V

Messages: 2337
Registered: March 2008
Location: Mounds View,MN

Karma: 0

Senior Member

Good luck with that.
I have read a few things about bearings and I doubt the balls hitting each other is the problem.
In fact it looks to me like the balls hit harder when they approach the bump.

Keith Vasilakes
Mounds View. MN
75 ex Royale GMC
ask me about MicroLevel
Cell, 763-732-3419
My427v8@hotmail.com

Report message to a moderator

Re: [GMCnet] Greaseless GMC Front Bearings? [message #278189 is a reply to message #278090]

Fri, 22 May 2015 07:54

JohnL455

Messages: 4447
Registered: October 2006
Location: Woodstock, IL

Karma: 12

Senior Member

I watched the video and still don't understand the concept. I would think that with no grease they would loose the "heat sink compound" effect that the grease helps provide.

John Lebetski
Woodstock, IL
77 Eleganza II

Report message to a moderator

Previous Topic:	[GMCnet] Honda Odyssey Seats
Next Topic:	[GMCnet] rear air valves

Goto Forum:

-=] Back to Top [=-

Current Time: Wed Nov 20 00:36:13 CST 2024

Total time taken to generate the page: 0.00808 seconds