Carter M6108 fuel pump, minor PITA [message #274429] |
Fri, 27 March 2015 09:59 |
|
Matt Colie
Messages: 8547 Registered: March 2007 Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
Just because I am paranoid, I elected to replace the engine fuel pump and the rubber line going to it. (With the knuckle out, this seemed like a good time to do it.) I removed the steel line first and it came off about as expected. R&R the pump and hose was only a problem because the upper fastener is a 1/6 of a turn at a time trick...
But, when it came time to put the steel line back in, there was a small disagreement. It was only a small mis-location of the fitting at the pump, but it completely prevented getting both the flare nuts started at the same time. I could have my choice, but no way could I get both. I tried re-bending the line and got it a lot closer, but lying there on my belly board and working around the AC pump was just no fun at all.
Finally I got it close enough to start at both ends, but the nuts would not run home easily. So, I let the carburetor free and ran them in. The carburetor holes were then about 1/4 hole off at the front and 1/2 off at the back.... I snugged up the line nuts and pushed the carburetor over to the holes and screwed it down... Done. I don't like it, but it is together.
Summary, if you have the engine clear enough to see the fuel pump and have any thought of replacing it, do it then. Later is a bear.
Matt
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
|
Re: [GMCnet] Carter M6108 fuel pump, minor PITA [message #274449 is a reply to message #274429] |
Fri, 27 March 2015 17:08 |
|
USAussie
Messages: 15912 Registered: July 2007 Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
Matt,
This makes R&Ring the carb and fuel pump a piece of cake, well worth forty bucks!
http://www.appliedgmc.com/prod.itml/icOid/853
Regards,
Rob M.
-----Original Message-----
From: Matt Colie
Just because I am paranoid, I elected to replace the engine fuel pump and the rubber line going to it. (With the knuckle out, this
seemed like a good time to do it.) I removed the steel line first and it came off about as expected. R&R the pump and hose was
only a problem because the upper fastener is a 1/6 of a turn at a time trick...
But, when it came time to put the steel line back in, there was a small disagreement. It was only a small mis-location of the
fitting at the pump, but it completely prevented getting both the flare nuts started at the same time. I could have my choice, but
no way could I get both. I tried re-bending the line and got it a lot closer, but lying there on my belly board and working around
the AC pump was just no fun at all.
Finally I got it close enough to start at both ends, but the nuts would not run home easily. So, I let the carburetor free and ran
them in. The carburetor holes were then about 1/4 hole off at the front and 1/2 off at the back.... I snugged up the line nuts and
pushed the carburetor over to the holes and screwed it down... Done. I don't like it, but it is together.
Summary, if you have the engine clear enough to see the fuel pump and have any thought of replacing it, do it then. Later is a
bear.
Matt
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|