GMCforum: GMCnet » Appreciating Dave Lenzi

Home » Public Forums » GMCnet » Appreciating Dave Lenzi

Show: Today's Messages :: Polls :: Message Navigator

Appreciating Dave Lenzi [message #265913]

Wed, 12 November 2014 07:56

Rick Williams

Messages: 256
Registered: July 2004

Karma: 0

Senior Member

I recently needed a new exhaust manifold gasket so I called Dave. I just thought that I would take a moment and express my appreciation and admiration of Dave. Many of you know him so you already know what a gentleman he is. You no doubt are aware of his extraordinary skills as well. I first met Dave about 12 years ago at a Sunshine Statesman's rally in Florida and we have crossed paths a few times since. I have purchased some of his products over the years and they are as good as anyone could make. His workmanship and attention to detail is an inspiration to do the best we can.
While he does not contribute to the GMCnet directly, his contribution here is enormous. Just look at how many times he is mentioned. Maybe working 10 hour days in your mid 70's to provide us GMCers with parts is enough of a contribution.
For those of you who are not familiar with Dave, take a few minutes and check out what he is doing and what he provides. Information is available here http://www.bdub.net/GMCSupplierLinks.html
I know that he will not see this post but I will say it anyway. Thanks Dave and see you down the road.

Rick

Rick Williams
Bliss, Michigan
1978 Eleganza II

Report message to a moderator

Re: [GMCnet] Appreciating Dave Lenzi [message #265917 is a reply to message #265913]

Wed, 12 November 2014 09:39

Mr ERFisher

Messages: 7117
Registered: August 2005

Karma: 2

Senior Member

On Wed, Nov 12, 2014 at 5:56 AM, Rick Williams wrote:

> I recently needed a new exhaust manifold gasket so I called Dave. I just
> thought that I would take a moment and express my appreciation and
> admiration
> of Dave. Many of you know him so you already know what a gentleman he is.
> You no doubt are aware of his extraordinary skills as well. I first met Dave
> about 12 years ago at a Sunshine Statesman's rally in Florida and we have
> crossed paths a few times since. I have purchased some of his products over
> the years and they are as good as anyone could make. His workmanship and
> attention to detail is an inspiration to do the best we can.
> While he does not contribute to the GMCnet directly, his contribution here
> is enormous. Just look at how many times he is mentioned. Maybe working 10
> hour days in your mid 70's to provide us GMCers with parts is enough of a
> contribution.
>

yes, i only met him at one rally
but he is one of our best vendor ( makes what no one else does)

> For those of you who are not familiar with Dave, take a few minutes and
> check out what he is doing and what he provides. Information is available
> here
> http://www.bdub.net/GMCSupplierLinks.html
>

why ?

> I know that he will not see this post but I will say it anyway. Thanks
> Dave and see you down the road.
>

hope he can make it to future rally's
erf

>
> Rick
> --
> Rick Williams
> Bliss, Michigan
> 1978 Eleganza II
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>

--
Gene Fisher -- 74-23,77PB/ore/ca
“Give a man a fish; you have fed him for today --- give him a URL and
-------
http://gmcmotorhome.info/
Alternator Protection Cable
http://gmcmotorhome.info/APC.html
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Report message to a moderator

Re: [GMCnet] Appreciating Dave Lenzi [message #265920 is a reply to message #265913]

Wed, 12 November 2014 09:51

bdub

Messages: 1578
Registered: February 2004
Location: Central Texas

Karma: 5

Senior Member

AMEN!

Here's a direct link:
http://www.bdub.net/lenzi/

FYI, prices are probably not up to date. And, I know that the product line
is lacking recent additions. Dave just doesn't have time for such matters.
He isn't real "email efficient", so a phone call is suggested.

bdub

-----Original Message-----
From: Gmclist On Behalf Of Rick Williams
Sent: Wednesday, November 12, 2014 7:56 AM

I recently needed a new exhaust manifold gasket so I called Dave. I just
thought that I would take a moment and express my appreciation and
admiration of Dave. Many of you know him so you already know what a
gentleman he is. You no doubt are aware of his extraordinary skills as well.
I first met Dave about 12 years ago at a Sunshine Statesman's rally in
Florida and we have crossed paths a few times since. I have purchased some
of his products over the years and they are as good as anyone could make.
His workmanship and attention to detail is an inspiration to do the best we
can.
While he does not contribute to the GMCnet directly, his contribution here
is enormous. Just look at how many times he is mentioned. Maybe working 10
hour days in your mid 70's to provide us GMCers with parts is enough of a
contribution.
For those of you who are not familiar with Dave, take a few minutes and
check out what he is doing and what he provides. Information is available
here http://www.bdub.net/GMCSupplierLinks.html
I know that he will not see this post but I will say it anyway. Thanks Dave
and see you down the road.

_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

bdub
'76 Palm Beach/Central Texas
www.bdub.net
www.gmcmhphotos.com
www.gmcmotorhomemarketplace.com
www.gmcmhregistry.com
www.facebook.com/groups/classicgmcmotorhomes
www.facebook.com/groups/gmcmm

Report message to a moderator

Re: Appreciating Dave Lenzi [message #265923 is a reply to message #265913]

Wed, 12 November 2014 10:34

77Royale

Messages: 461
Registered: June 2014
Location: Mid Michigan

Karma: 6

Senior Member

Could not agree more. I have had the pleasure of meeting and talking with him a few times as I am pretty close to the skunk works. I keep asking if he wants an apprentice.

77 Royale, Rear Dry Bath. 403, 3.55 Final Drive, Lenzi goodies, Patterson carb and dizzy. Mid Michigan

Report message to a moderator

Re: Appreciating Dave Lenzi [message #265926 is a reply to message #265913]

Wed, 12 November 2014 11:54

kerry pinkerton

Messages: 2565
Registered: July 2012
Location: Harvest, Al

Karma: 15

Senior Member

Among a group of guys who are 'class acts', Dave is one of the best. I've had the pleasure of spending time with him at 3 GMCMI rallies now. He is one sharp cookie and a nicer guy you just won't find.

Kerry Pinkerton - North Alabama Had 5 over the years. Currently have a '06 Fleetwood Discovery 39L

Report message to a moderator

Re: Appreciating Dave Lenzi [message #265928 is a reply to message #265926]

Wed, 12 November 2014 12:30

Matt Colie

Messages: 8547
Registered: March 2007
Location: S.E. Michigan

Karma: 7

Senior Member

Some of you may have noticed that he did not make it to Chippewa Falls and it was said that this was a result of medical issues. As much as I did not want to pry, I called and got to talk to Mary. Fortunately, that was my plan from the get-go.

Dave is doing OK. I did not ask for specifics, but he has finished the round of Chemo and starts a radiation sequence in a week or so. That will probably keep him slow until about spring. We can all just hope and pray that this works for him.

I figure I still owe him at least one good diner.

Matt

Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit

Report message to a moderator

Re: Appreciating Dave Lenzi [message #265966 is a reply to message #265913]

Thu, 13 November 2014 08:53

JohnL455

Messages: 4447
Registered: October 2006
Location: Woodstock, IL

Karma: 12

Senior Member

Here here for Dave. I've had the privilidge of tagging along during his front end shake downs and found several worn parts or improperly installed parts for owners. He is a great teacher and his explanation of how to optimze allignment allowed me to DIY mine with the Jerry Work kit and getting over 4 deg caster on my coach. No offset bushings. Drives great and my front tires and fuel economy are happy as welll. Dave is a master of KISS but with well placed improvements where warranted. Feel better.

John Lebetski
Woodstock, IL
77 Eleganza II

Report message to a moderator

Re: [GMCnet] Appreciating Dave Lenzi [message #265971 is a reply to message #265966]

Thu, 13 November 2014 09:31

Kimberlea Weeks

Messages: 675
Registered: July 2010

Karma: 6

Senior Member

Received a message from Dave a couple days ago. He mentioned that he is
going to fight this thing and plans on being at the Spring Convention in
Patterson, Lousiana.

*Kimberlea Weeks*
VP Administration and Convention Manager
612.501.4600 | f.866.519.0047 | www.gmcmi.com

*GMC Motorhomes International*
1402 So. Cage Blvd | Unit 273 | Pharr | TX 78577

*Mark this on your calendar today!*

*GMCMI 2015 Spring Convention* | Friday, March 27 to Thursday, April 2
Kemper Williams Park & Patterson Area Civic Center | Patterson, Louisiana

*GMCMI 2015 Fall Convention* | Friday, September 25 to Thursday, October 1
Central States Fairgrounds | Rapid City, South Dakota

On Thu, Nov 13, 2014 at 8:53 AM, John R. Lebetski
wrote:

> Here here for Dave. I've had the privilidge of tagging along during his
> front end shake downs and found several worn parts or improperly installed
> parts for owners. He is a great teacher and his explanation of how to
> optimze allignment allowed me to DIY mine with the Jerry Work kit and
> getting
> over 4 deg caster on my coach. No offset bushings. Drives great and my
> front tires and fuel economy are happy as welll. Dave is a master of KISS
> but
> with well placed improvements where warranted. Feel better.
> --
> John Lebetski
> Woodstock, IL
> 77 Eleganza II
> Source America First
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Report message to a moderator

Re: [GMCnet] Appreciating Dave Lenzi [message #266021 is a reply to message #265928]

Thu, 13 November 2014 17:34

USAussie

Messages: 15912
Registered: July 2007
Location: Sydney, Australia

Karma: 6

Senior Member

G'day,

Both Double Trouble and The Blue Streak have Dave's remanufactured:

Hubs
Knuckles
Idler Arm
Relay Lever
Sensitized Booster
Offset Upper Control Arms

The quality of the workmanship on those parts exceeds OEM by a long shot!

Regards,
Rob M.
Sydney, Australia
AUS '75 Avion - The Blue Streak TZE365V100428
USA '75 Avion - Double Trouble TZE365V100426

_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Regards, Rob M. (USAussie) The Pedantic Mechanic Sydney, Australia '75 Avion - AUS - The Blue Streak TZE365V100428 '75 Avion - USA - Double Trouble TZE365V100426

Report message to a moderator

Re: [GMCnet] Appreciating Dave Lenzi [message #266039 is a reply to message #265971]

Thu, 13 November 2014 22:00

kerry pinkerton

Messages: 2565
Registered: July 2012
Location: Harvest, Al

Karma: 15

Senior Member

Kimberlea Weeks wrote on Thu, 13 November 2014 09:31

Received a message from Dave a couple days ago. He mentioned that he is
going to fight this thing and plans on being at the Spring Convention in
Patterson, Lousiana....

That is great news.

Kerry Pinkerton - North Alabama Had 5 over the years. Currently have a '06 Fleetwood Discovery 39L

Report message to a moderator

Previous Topic:	[GMCnet] Suburban Furnace Part Numbers, And Source
Next Topic:	Re: [GMCnet] Totally off topic. My teenage son has a job interview with Harbor Freight.

Goto Forum:

-=] Back to Top [=-

Current Time: Thu Oct 03 06:13:08 CDT 2024

Total time taken to generate the page: 0.03823 seconds