Swapping Buzz box for progressive dynamics PD 9260 [message #260398] |
Thu, 28 August 2014 20:54 |
MikeT
Messages: 225 Registered: November 2009 Location: Marine City, Michigan
Karma: 0
|
Senior Member |
|
|
Finally swapping it out and want to make sure that all I need to do is cut the positive and negative cables off the buzz box and hook them up to progressive dynamics converter PD 9260?
Thanks, hope it's that simple.
Mike Thomas
Marine City, MI
77 ex Palm Beach
|
|
|
Re: [GMCnet] Swapping Buzz box for progressive dynamics PD 9260 [message #260402 is a reply to message #260398] |
Thu, 28 August 2014 21:57 |
powerjon
Messages: 2446 Registered: January 2004
Karma: 5
|
Senior Member |
|
|
Mike,
Which coach are you changing out the converter/charge in? Just make sure that you hitch the positive to positive and the negative to negative. Mark the wires BEFORE you disconnect you disconnect them. Both GMC and Coachman used black wire for both leads most of the time. Don’t cut the wires too short on the Buzz Box and it can be used for a number of projects. The positive should go to the fuse block and the negative will go to the body. I would suggest that you clean the connection to the aluminum body strut and put some dielectric grease on the connection. I would also suggest that you put new wire from the charger to the ground, black #8 and to the fuse block, #8 red.
JR Wright
78 Buskirk Stretch
75 Avion
Michigan
On Aug 28, 2014, at 9:54 PM, Thomas Mike wrote:
> Finally swapping it out and want to make sure that all I need to do is cut the positive and negative cables off the buzz box and hook them up to
> progressive dynamics converter PD 9260?
>
> Thanks, hope it's that simple.
> --
> Mike Thomas
> Troy, MI
> 77 ex Palm Beach, 77 Royale (rear bath)
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
J.R. Wright
GMC GreatLaker
GMC Eastern States
GMCMI
78 30' Buskirk Stretch
75 Avion Under Reconstruction
Michigan
|
|
|
|
|
Re: [GMCnet] Swapping Buzz box for progressive dynamics PD 9260 [message #260446 is a reply to message #260424] |
Fri, 29 August 2014 10:25 |
powerjon
Messages: 2446 Registered: January 2004
Karma: 5
|
Senior Member |
|
|
Mike,
The #8 wire is not that expensive, go to your favorite hardware store or Big Box store and get 3 or 4 feet each of red and black. You will need 1 or 2 wire connector for the one end to the body. Do it right the first time!
JR Wright
78 Buskirk Stretch
75 Avion
Michigan
On Aug 29, 2014, at 8:56 AM, Thomas Mike wrote:
> Thanks JR. It's the a Palm Beach. I Wanted to just cut and reuse wires from buzz box and at a later date run new #8. I'll give it a whirl.
> --
> Mike Thomas
> Troy, MI
> 77 ex Palm Beach, 77 Royale (rear bath)
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
J.R. Wright
GMC GreatLaker
GMC Eastern States
GMCMI
78 30' Buskirk Stretch
75 Avion Under Reconstruction
Michigan
|
|
|