Onan Flywheel Torque [message #258978] |
Fri, 15 August 2014 21:40 |
|
Jerry Sitzlar
Messages: 206 Registered: February 2013 Location: Lenoir City, TN
Karma: 4
|
Senior Member |
|
|
After spending nearly a week cleaning about 37 years of dirt, grease, oil, oily leaves, and whatever else I could find. Then replacing the front crankshaft seal, torquing down the loose bolts on the governor case, the oil filter mount, and replacing the leaking oil pressure switch, my Onan is purring like a kitten and not leaking oil. The question is: What do you guys torque the flywheel to? I ask the question because the manual X-7525B states on page 24c-33 in the paragraph right after step 12 to torque at 45 ft lbs and it refers to both 4 and 6 KW. Now on page 24c-52, same manual, in the 6KW Torque Specs to torque at 35-40 ft lbs. Just to be in the middle, I used 40. Is this a good number? Anyway, tomorrow I install the Bovee Pertronic Electronic Ignition, now that I know it is running good.
Jerry (Sitz)
Jerry Sitzlar..... 77 Eleganza II, Twin bed, dry bath...... Lenoir City, TN (near Knoxville)
|
|
|
Re: [GMCnet] Onan Flywheel Torque [message #259022 is a reply to message #258978] |
Sat, 16 August 2014 08:18 |
|
USAussie
Messages: 15912 Registered: July 2007 Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
Jerry,
Onan 6kw NH Major Servic3 Manual page 7 notes:
ASSEMBLY TORQUES
TORQUE SPECIFICATIONS IN LB. FT.
Flywheel Mounting Screw 35 MIN 40 MAX
http://www.bdub.net/manuals/Onan/Onan6kwNH_Major-Service.pdf
You're fine.
Regards,
Rob M.
The Pedantic Mechanic
USAussie - Downunder
USA '75 Avion - Double Trouble TZE365V100426
AUS '75 Avion - The Blue Streak TZE365V100428
-----Original Message-----
From: Jerry Sitzlar
After spending nearly a week cleaning about 37 years of dirt, grease, oil, oily leaves, and whatever else I could find. Then
replacing the front crankshaft seal, torquing down the loose bolts on the governor case, the oil filter mount, and replacing the
leaking oil pressure switch, my Onan is purring like a kitten and not leaking oil. The question is: What do you guys torque the
flywheel to? I ask the question because the manual X-7525B states on page 24c-33 in the paragraph right after step 12 to torque at
45 ft lbs and it refers to both 4 and 6 KW. Now on page 24c-52, same manual, in the 6KW Torque Specs to torque at 35-40 ft lbs.
Just to be in the middle, I used 40. Is this a good number? Anyway, tomorrow I install the Bovee Pertronic Electronic Ignition,
now that I know it is running good.
Jerry
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|