Rusty frame [message #257501] |
Fri, 01 August 2014 22:59 |
thorndike
Messages: 406 Registered: January 2011 Location: Conifer, Colorado
Karma: 0
|
Senior Member |
|
|
Like most of us, I have a good bit of rust on parts of my frame. While I would love to find a way to do an off frame restoration and completely blast, prime, and seal my frame, it is not in the financial cards. I know that there are paints/chemicals that claim to combine with the rust leaving a finish ready for paint. I believe one of them is called Marhyde One Step or something like that.
What do folks consider the best way to treat the rusty frame?
Bob
Robert Peesel
1976 Royale 26'
Side Dry Bath
Conifer, Colorado
|
|
|
Re: Rusty frame [message #257503 is a reply to message #257501] |
Fri, 01 August 2014 23:08 |
GMC Cruse
Messages: 606 Registered: June 2009 Location: SE Michigan
Karma: 3
|
Senior Member |
|
|
thorndike wrote on Fri, 01 August 2014 23:59Like most of us, I have a good bit of rust on parts of my frame. While I would love to find a way to do an off frame restoration and completely blast, prime, and seal my frame, it is not in the financial cards. I know that there are paints/chemicals that claim to combine with the rust leaving a finish ready for paint. I believe one of them is called Marhyde One Step or something like that.
What do folks consider the best way to treat the rusty frame?
Bob
I've used POR-15 and had good results on my classic cars.
http://www.por15.com/POR-15-Rust-Preventive-Coating_p_8.html
Mike K.
'75 PB
Southeast Michigan
|
|
|
Re: [GMCnet] Rusty frame [message #257505 is a reply to message #257503] |
Fri, 01 August 2014 23:38 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
If your frame has rust that has eaten through the frame,you'll need to
repiair it.
Should you have a ruty frame, take transmission fluid and spray it on
I know it willl stop it and easy to do
Dan Stucky recommends us to do it.
He is our guy when it comes to replacing frame and sections;
Transmission fluid does not gather dirt/dust like petroleum oil or grease.
On Fri, Aug 1, 2014 at 9:08 PM, Mike wrote:
> thorndike wrote on Fri, 01 August 2014 23:59
>> Like most of us, I have a good bit of rust on parts of my frame. While
> I would love to find a way to do an off frame restoration and completely
>> blast, prime, and seal my frame, it is not in the financial cards. I
> know that there are paints/chemicals that claim to combine with the rust
>> leaving a finish ready for paint. I believe one of them is called
> Marhyde One Step or something like that.
>>
>> What do folks consider the best way to treat the rusty frame?
>>
>> Bob
>
>
> I've used POR-15 and had good results on my classic cars.
>
> http://www.por15.com/POR-15-Rust-Preventive-Coating_p_8.html
> --
> Mike K.
> '75 PB
> Southeast Michigan
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Jim Kanomata
Applied/GMC, Fremont,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Re: Rusty frame [message #257511 is a reply to message #257501] |
Sat, 02 August 2014 07:10 |
Joe Weir
Messages: 769 Registered: February 2013 Location: Columbia, SC
Karma: 7
|
Senior Member |
|
|
As long as it is surface rust, I will second POR15. It is moisture curing urethane, and gets pretty darn hard. Can be used for all sorts of repairs when combined with cloth. They make a chassis coat product that is made for frames. Hit the surface with ospho or some such treatment and then the POR15 and the rust stops.
There is another product called Rust bullet - pretty much the same thing, only UV stable and silver in color.
On the unproven front, I used some of Rustoleums new spray on rust converter/topcoat on a few non-structural bits to see how well it contains. So far seems to hold up well. I used it on the outside of the brake master:
http://www.gmcmhphotos.com/photos/data/6394/medium/Master_cylinder.jpg
Which will be interesting to see how it holds up to brake fluid as well. This Picture was taken after 3 months. Infamous PO wire nut seen in background - I think this would be from the "how do I turn off the dash fan" hack.
76 Birchaven - "Wicked Mistress" - New engine, trans, alum radiator, brakes, Sully airbags, fuel lines, seats, adult beverage center... those Coachmen guys were really thinking about us second hand owners by including that beverage center...
Columbia, SC.
[Updated on: Sat, 02 August 2014 07:14] Report message to a moderator
|
|
|
|