[GMCnet] Where / How To Use Silicone / RTV [message #245934] |
Mon, 31 March 2014 19:31 |
|
USAussie
Messages: 15912 Registered: July 2007 Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
G'day,
I thought I'd start a discussion to outline where and how to use silicone / RTV when building an engine.
If you think anything I have noted below is incorrect PLEASE comment!
You could use silicone / RTV when building an engine:
1) On the intake manifold gaskets and front / rear lifter valley contact area
2) On the valve cover gaskets
3) On the timing chain cover gasket
4) On the water pump gaskets
5) On the oil pan gasket
6) On the juncture of the oil pan gasket and front / rear rubber seals
7) On the freeze plugs
Where you would not use silicone / RTV:
Caveats:
1) Only use silicone / RTV that is safe for Electronic Fuel Injection Oxygen Sensors.
2) Only use enough silicone / RTV to provide a good seal and not in excess where blobs might come off inside the engine.
3) Use the correct silicone / RTV for the area you are sealing.
Regards,
Rob M.
Sydney, Australia
AUS '75 Avion - The Blue Streak TZE365V100428
USA '75 Avion - Double Trouble TZE365V100426
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
|
Re: [GMCnet] Where / How To Use Silicone / RTV [message #245959 is a reply to message #245934] |
Mon, 31 March 2014 20:58 |
GMC_LES
Messages: 569 Registered: October 2009 Location: Montreal
Karma: 0
|
Senior Member |
|
|
I may be stating the obvious, but here are a few suggestions.
Do not use RTV where it will come in contact with fuels. It turns to a jelly like substance and can cause untold problems.
Do not use RTV on surfaces that you may want to paint. Paint does not stick to most RTVs.
If you need to remove cured RTV and do not want to damage the underlying surface, soak or submerse the RTV in kerosene, gasoline, or a similar fuel. It may take 24 hours or more to remove, so patience is necessary. We use kerosene here on the jet engines we overhaul.
Les Burt
Montreal
1975 Eleganza 26ft
A work in Progress
On Mar 31, 2014, at 8:31 PM, "Robert Mueller" <robmueller@iinet.net.au> wrote:
G'day,
I thought I'd start a discussion to outline where and how to use silicone / RTV when building an engine.
If you think anything I have noted below is incorrect PLEASE comment!
You could use silicone / RTV when building an engine:
1) On the intake manifold gaskets and front / rear lifter valley contact area
2) On the valve cover gaskets
3) On the timing chain cover gasket
4) On the water pump gaskets
5) On the oil pan gasket
6) On the juncture of the oil pan gasket and front / rear rubber seals
7) On the freeze plugs
Where you would not use silicone / RTV:
Caveats:
1) Only use silicone / RTV that is safe for Electronic Fuel Injection Oxygen Sensors.
2) Only use enough silicone / RTV to provide a good seal and not in excess where blobs might come off inside the engine.
3) Use the correct silicone / RTV for the area you are sealing.
Regards,
Rob M.
Sydney, Australia
AUS '75 Avion - The Blue Streak TZE365V100428
USA '75 Avion - Double Trouble TZE365V100426
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Les Burt
Montreal
1975 Eleganza 26ft
A work in Progress
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Les Burt
Montreal
1975 Eleganza 26ft
A work in Progress
|
|
|