|
Re: Dobbelt trøbbel get's some much needed TLC [message #245379 is a reply to message #245303] |
Thu, 27 March 2014 17:59 |
|
Loffen
Messages: 1087 Registered: August 2013 Location: Norway
Karma: 1
|
Senior Member |
|
|
Not so many pictures today.
The old plug,
Old vs New and shiny, I prefer to use brass pluggs as they do not rust, the old one was not so old by the way, the engine has been out of the coach and overhauled by a previous owner.
The new one is in and no leaks, I had to take of the oil filter adapter to be able to mount it.
And the new exhaust manifold gasket, I allways use a thin layer of high temp silicon on them when the surface has not been machined just to make sure that it seals.
I did also re thighten the transmission chain cover since there was a small leak and did change the water temp sensor and a aftermarked water temp gauge as it was way off.
Tomorrow I hope to get the mufflers back on and change oil and filter on the transmission, at the same time I will also change the O-rings on the modulator and selector shaft.
1973 23' # 1848 Sky Blue Glacier called Baby Blue and a 1973 26'-3 # 1460 Parrot green Seqouia Known as the Big Green,
And sold my 1973 26'-2 # 581 White Canyon lands under the name Dobbelt trøbbel
in Norway
[Updated on: Thu, 27 March 2014 18:16] Report message to a moderator
|
|
|
Re: Dobbelt trøbbel get's some much needed TLC [message #245437 is a reply to message #245303] |
Thu, 27 March 2014 22:11 |
Ultravan Owners
Messages: 443 Registered: March 2013
Karma: 0
|
Senior Member |
|
|
Espen,
Do you spread the high temp silicon to thin it out and make it more even before you install those gaskets?
I hope you don't mind me saying. That is a little too much high temp silicon unless you do spread it out evenly before installing.
Keep up the progress.
Tony (Ontario Canada) Marie and I are blessed to have had a 2nd chance to buy our farm. Still hoping and more importantly praying to be able to build a garage. Our 1970 Ultravan #520 has an Olds Toronado 455 in back.
|
|
|
Re: Dobbelt trøbbel get's some much needed TLC [message #245453 is a reply to message #245437] |
Thu, 27 March 2014 23:01 |
Bob de Kruyff
Messages: 4260 Registered: January 2004 Location: Chandler, AZ
Karma: 1
|
Senior Member |
|
|
Ultravan Owners wrote on Thu, 27 March 2014 21:11 | Espen,
Do you spread the high temp silicon to thin it out and make it more even before you install those gaskets?
I hope you don't mind me saying. That is a little too much high temp silicon unless you do spread it out evenly before installing.
Keep up the progress.
|
I normally spread it on heavily--what's wrong with that?
Bob de Kruyff
78 Eleganza
Chandler, AZ
|
|
|
|
|
Re: Dobbelt trøbbel get's some much needed TLC [message #245499 is a reply to message #245303] |
Fri, 28 March 2014 09:31 |
Ultravan Owners
Messages: 443 Registered: March 2013
Karma: 0
|
Senior Member |
|
|
Espen that engine on the stand looks nice!
As a mechanic I have seen a good amount of engines go bad due to the over use of silicon sealer.
When I had my own business and things were slow I would do consignment for a company call Motor Exchange in Arlington, VA.
A good friend of mine, Donald, ran the place and I enjoyed working with him and going to lunch to catch up.
Before that time I worked for GM dealership and for some time GM uses it in place of a gasket on their engines. To see a mechanic do a needed repair and replace that silicon the wrong way and the end results. Oh well been there seen that too.
Anyways, It seemed like a habit. When you see it used a lot in one place or another it is used just as much if not more elsewhere too.
To know where, when, just how much to use and why the concern is.
I have seen the stuff in all kinds of places inside an engine and even an oil and transmissions pan.
We had to replace engines due to installer's mistakes or the shade tree mechanic doing some work at home.
But I will have to politely disagree with you both.
When the silicon is standing up like a small pile from the beginning or the end of it being applied, not smoothed out, or one can see it out the edge of where it was installed when things get tightened up = too much. And if you don't see it - does not mean it was not too much. With tolerances so tight/close to begin with the extra stuff has to go somewhere and there is always the opposite side (inward) that one cannot see - until it is too late.
So YES - maybe I'm a little extra cautious! However, I rather say something than to see a person screw up their hard work and learn it the hard way.
So shoot me...
Sincerely, Tony
Tony (Ontario Canada) Marie and I are blessed to have had a 2nd chance to buy our farm. Still hoping and more importantly praying to be able to build a garage. Our 1970 Ultravan #520 has an Olds Toronado 455 in back.
|
|
|
|