Synpower to the rescue again [message #241789] |
Fri, 28 February 2014 15:08 |
JohnL455
Messages: 4447 Registered: October 2006 Location: Woodstock, IL
Karma: 12
|
Senior Member |
|
|
Fan in my laptop was sounding like a bad GMC heater / AC blower squealing and rattling. Tryed 2 different times to order a replacement on eBay for my model X61s and got slightly different styles that wouldn't fit. Getting tired of taking out lots of jewelers screws to work on it and find I have a non usable replacement. Tryed spraying different lube things in there with some minor success, but the bearing wear was still causing it to sound obnoxoius and nothing lasted. So I gave it one last try, took the fan apart at using a q-tip put a fraction of a drop of Valvoline Synpower on the the tiny fan shaft. Purring like a kitten. That's all I buy anymore is Synpower.
John Lebetski
Woodstock, IL
77 Eleganza II
|
|
|
Re: Synpower to the rescue again [message #241790 is a reply to message #241789] |
Fri, 28 February 2014 15:13 |
tphipps
Messages: 3005 Registered: August 2004 Location: Spanish Fort, AL
Karma: 9
|
Senior Member |
|
|
I used SynPower to lubricate moving parts on my closet doors. Detent balls were installed and getting a little tough to snap open or shut. A little dab of SynPower, and they roll like new.
Tom, MS II
2012 Phoenix Cruiser model 2552
KA4CSG
|
|
|
Re: Synpower to the rescue again [message #241791 is a reply to message #241789] |
Fri, 28 February 2014 15:16 |
JohnL455
Messages: 4447 Registered: October 2006 Location: Woodstock, IL
Karma: 12
|
Senior Member |
|
|
Just don't get it on the clothes or carpets! As ususal stuff that works best is pretty nasty staining wise. Thought it might be too thick for the little micro fan motor to spin but no problem.
John Lebetski
Woodstock, IL
77 Eleganza II
|
|
|
Re: Synpower to the rescue again [message #241794 is a reply to message #241789] |
Fri, 28 February 2014 15:37 |
Ken Burton
Messages: 10030 Registered: January 2004 Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
I wish I had though of that. I went through two Chinese junk replacement fans on an old T30 last year. I eventually bought a genuine replacement and took care of the problem. If I ever have another fan problem I'll try your trick. The machine I was replacing it on is one that runs 24x7 forwarding APRS packets off of the air to the Internet. The fan died after 8 years of continuous operation. Maybe I ought to preemptively take it apart and lubricate it.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
Re: [GMCnet] Synpower to the rescue again [message #241819 is a reply to message #241794] |
Fri, 28 February 2014 17:54 |
jhbridges
Messages: 8412 Registered: May 2011 Location: Braselton ga
Karma: -74
|
Senior Member |
|
|
I keep maybe ten different size fans on hand, evertyhing we have uses them any more, and they're all different. Pretty much all of them can be had though. Between Mouser and DigiKey I've been able to source by size and current draw. So far, I've always been able to find ball bearing ones, which outlast the sleeve bearings by far. I'd been using a synthetic lube from GC, but I'm gonna go get some Synpower. It will be cheaper and seems to do as well or better.
All these fans are made on the Pacific Rim, so I lube them before install.
--johnny
________________________________
From: Ken Burton <n9cv@comcast.net>
To: gmclist@temp.gmcnet.org
Sent: Friday, February 28, 2014 4:37 PM
Subject: Re: [GMCnet] Synpower to the rescue again
I wish I had though of that. I went through two Chinese junk replacement fans on an old T30 last year. I eventually bought a genuine replacement and took care of the problem. If I ever have another fan problem I'll try your trick. The machine I was replacing it on is one that runs 24x7 forwarding APRS packets off of the air to the Internet. The fan died after 8 years of continuous operation. Maybe I ought to preemptively take it apart and lubricate it.
--
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.
I forgive them all, save those who hurt the dogs. They must answer to me in hell
|
|
|
Re: Synpower to the rescue again [message #241827 is a reply to message #241789] |
Fri, 28 February 2014 19:02 |
JohnL455
Messages: 4447 Registered: October 2006 Location: Woodstock, IL
Karma: 12
|
Senior Member |
|
|
I had luck in the past with Cailube MCL spray but this bearing had been dry too long and had a touch of slop. The SynPower is viscous enough to make up the tollerance. So easy to pull out the fan wheel as the field just holds the assembly centered. Used a head of pin sized quantity. I almost ordered a new computer today but dodged it for now.
John Lebetski
Woodstock, IL
77 Eleganza II
|
|
|