GMCforum
For enthusiast of the Classic GMC Motorhome built from 1973 to 1978. A web-based mirror of the GMCnet mailing list.
Home » Public Forums » GMCnet » switch 6k to 4k generators what is differant? (generator problems (again?))
switch 6k to 4k generators what is differant? [message #221786] Mon, 09 September 2013 15:09 Go to next message
JJUNKSELL is currently offline  JJUNKSELL   United States
Messages: 58
Registered: July 2013
Location: MERIDEN CT
Karma: 0
Member
I bought a 76 pb the gen was out of it. the po said a 4 k came w/ it when he bought it.I have the power drawer and the 4k gen.there is a mount that is bolted to the frame.the power drawers mounting holes seem to line up,3 of them on the right side facing the gen compartment. when the 3 bolts are tightend the left side comes up about 1/2 inch.there are two mounting holes on the bottem of the power drawer on the left side,that mount to the frame. is the power drawer supposed to sit on the frame of the mh? I put washers under it to support it. has anyone else run into this problem? thanks Dave

Dave, 76 PB moneypit.Center of CT.

Report message to a moderator

Re: switch 6k to 4k generators what is differant? [message #221809 is a reply to message #221786] Mon, 09 September 2013 16:45 Go to previous messageGo to next message
A Hamilto is currently offline  A Hamilto   United States
Messages: 4508
Registered: April 2011
Karma: 39
Senior Member
JJUNKSELL wrote on Mon, 09 September 2013 15:09

I bought a 76 pb the gen was out of it. the po said a 4 k came w/ it when he bought it.I have the power drawer and the 4k gen.there is a mount that is bolted to the frame.the power drawers mounting holes seem to line up,3 of them on the right side facing the gen compartment. when the 3 bolts are tightend the left side comes up about 1/2 inch.there are two mounting holes on the bottem of the power drawer on the left side,that mount to the frame. is the power drawer supposed to sit on the frame of the mh? I put washers under it to support it. has anyone else run into this problem? thanks Dave
The power drawer is NOT supposed to sit on the GMC frame. The bracket supports it about 1-3/8" above the frame.

There is a bracket that bolts to the frame with 4 bolts. The power drawer bolts down to that bracket with 4 bolts in a rectangular pattern.

I have not seen an original frame bracket up close and personal, but the back 2 bolts on the 23' bolt to the rear subframe, not the frame rails, and there needs to be about a 1/8" offset for the thickness of the metal. I don't know if that offset is in the bracket or if GM used spacers. If that offset is in the bracket, then you need to use a spacer to move the front of the bracket away from the frame rails that 1/8"

Here's what the bracket and power drawer look like. You can see the 4 holes in the power drawer.
http://www.gmcmhphotos.com/photos/data/6072/medium/2012-03-11_16-41-19_738.jpg
http://www.gmcmhphotos.com/photos/data/6072/medium/2012-03-11_16-41-19_738.jpg

Report message to a moderator

Re: switch 6k to 4k generators what is differant? [message #221820 is a reply to message #221786] Mon, 09 September 2013 17:23 Go to previous messageGo to next message
JJUNKSELL is currently offline  JJUNKSELL   United States
Messages: 58
Registered: July 2013
Location: MERIDEN CT
Karma: 0
Member
is that pic a 6k? or a 4k? everything looks diff from mine. i have a 4k im putting in.

Dave, 76 PB moneypit.Center of CT.

Report message to a moderator

Re: switch 6k to 4k generators what is differant? [message #221821 is a reply to message #221820] Mon, 09 September 2013 17:26 Go to previous messageGo to next message
A Hamilto is currently offline  A Hamilto   United States
Messages: 4508
Registered: April 2011
Karma: 39
Senior Member
JJUNKSELL wrote on Mon, 09 September 2013 17:23

is that pic a 6k? or a 4k? everything looks diff from mine. i have a 4k im putting in.
That pic is a 4k.

If yours looks different, maybe yours is not out of a GMC.

Report message to a moderator

Re: switch 6k to 4k generators what is differant? [message #221822 is a reply to message #221786] Mon, 09 September 2013 17:26 Go to previous messageGo to next message
Dennis S is currently offline  Dennis S   United States
Messages: 3046
Registered: November 2005
Karma: 2
Senior Member
JJUNKSELL wrote on Mon, 09 September 2013 15:09

I bought a 76 pb the gen was out of it. the po said a 4 k came w/ it when he bought it.I have the power drawer and the 4k gen.there is a mount that is bolted to the frame.the power drawers mounting holes seem to line up,3 of them on the right side facing the gen compartment. when the 3 bolts are tightend the left side comes up about 1/2 inch.there are two mounting holes on the bottem of the power drawer on the left side,that mount to the frame. is the power drawer supposed to sit on the frame of the mh? I put washers under it to support it. has anyone else run into this problem? thanks Dave


Dave

Here is a photo of my 4KW -- note it is installed in a 23 ft.

http://www.gmcmhphotos.com/photos/g6363-onan-4kw-compartment.html

Dennis

Dennis S
73 Painted Desert 230
Memphis TN Metro

Report message to a moderator

Re: switch 6k to 4k generators what is differant? [message #221824 is a reply to message #221786] Mon, 09 September 2013 17:30 Go to previous messageGo to next message
C Boyd is currently offline  C Boyd   United States
Messages: 2629
Registered: April 2006
Karma: 18
Senior Member
here are some pics of the 4k in the Birch.
http://www.gmcmhphotos.com/photos/g6270-4k-onan-bracket.html







JJUNKSELL wrote on Mon, 09 September 2013 16:09

I bought a 76 pb the gen was out of it. the po said a 4 k came w/ it when he bought it.I have the power drawer and the 4k gen.there is a mount that is bolted to the frame.the power drawers mounting holes seem to line up,3 of them on the right side facing the gen compartment. when the 3 bolts are tightend the left side comes up about 1/2 inch.there are two mounting holes on the bottem of the power drawer on the left side,that mount to the frame. is the power drawer supposed to sit on the frame of the mh? I put washers under it to support it. has anyone else run into this problem? thanks Dave



C. Boyd
76 Crestmont
East Tennessee

Report message to a moderator

Re: switch 6k to 4k generators what is differant? [message #221826 is a reply to message #221822] Mon, 09 September 2013 17:43 Go to previous messageGo to next message
JJUNKSELL is currently offline  JJUNKSELL   United States
Messages: 58
Registered: July 2013
Location: MERIDEN CT
Karma: 0
Member
Dennis mine looks like yours. the mounting holes are in a triangle pattern on the left side of the drawer.dang i shoulda taken some pics so i can look at them lol.

Dave, 76 PB moneypit.Center of CT.

Report message to a moderator

Re: switch 6k to 4k generators what is differant? [message #221827 is a reply to message #221826] Mon, 09 September 2013 18:01 Go to previous messageGo to next message
Dennis S is currently offline  Dennis S   United States
Messages: 3046
Registered: November 2005
Karma: 2
Senior Member
JJUNKSELL wrote on Mon, 09 September 2013 17:43

Dennis mine looks like yours. the mounting holes are in a triangle pattern on the left side of the drawer.dang i shoulda taken some pics so i can look at them lol.


Dave
If it was previously installed -- and you have all the pieces, it should be straightforward.
The forward part in Mark's post bolts to the frame, the drawer bolts to that piece and essentially cantilevers the Onan into the compartment.

Dennis

Dennis S
73 Painted Desert 230
Memphis TN Metro

Report message to a moderator

Re: switch 6k to 4k generators what is differant? [message #221829 is a reply to message #221827] Mon, 09 September 2013 18:19 Go to previous message
JJUNKSELL is currently offline  JJUNKSELL   United States
Messages: 58
Registered: July 2013
Location: MERIDEN CT
Karma: 0
Member
some of the holes dont look like factory drilled holes thats why im trying to cheak it out and see if it is rite.

Dave, 76 PB moneypit.Center of CT.

Report message to a moderator

Previous Topic: [GMCnet] Onan Mufflers. Misunderstanding Happen
Next Topic: Visitation Report
Goto Forum:
  


Current Time: Fri Sep 20 02:30:49 CDT 2024

Total time taken to generate the page: 0.01363 seconds
.:: Contact :: Home ::.

Powered by: FUDforum 3.1.1.
Copyright ©2001-2021 FUDforum Bulletin Board Software