Honda ev4010 [message #207552] |
Mon, 13 May 2013 11:04 |
tphipps
Messages: 3005 Registered: August 2004 Location: Spanish Fort, AL
Karma: 9
|
Senior Member |
|
|
For those of you who wish to install the Honda ev4010 GenSet with an undermount exhaust, I have a set of scanned images of the actual size unit mounting plate. Unfortunately, it is 12 scanned images. Unable to find a large size scanner in this no horse town.
If Wal-Mart does not stock it, you cannot buy it.
The file for the Honda ev6010 is on Billy's site. It will print actual size when printed on a large scale printer.
Anyhow, P.M. me if you wish the set e-mailed to you.
Tom, MS II
2012 Phoenix Cruiser model 2552
KA4CSG
|
|
|
|
Re: Honda ev4010 [message #207584 is a reply to message #207552] |
Mon, 13 May 2013 13:34 |
Chr$
Messages: 2690 Registered: January 2004 Location: Scottsdale, AZ
Karma: 1
|
Senior Member |
|
|
It's really handy. I used it to figure out where I am going to mount mine. I have the original that came with my 4010 and the guy even gave me the steel plate he had made to match it! All I gotta do is bolt and RTV it (for vibration) to the frame rails and I'm good to go.
These generators are nice. A bit loud, but I'm hoping once I have it in an enclosed compartment, it will be quieter.
-Chr$: Perpetual SmartAss
Scottsdale, AZ
77 Ex-Kingsley 455 SOLD!
2010 Nomad 24 Ft TT 390W PV W/MPPT, EV4010 and custom cargo door.
Photosite: Chrisc GMC:"It has Begun" TT: "The Other Woman"
|
|
|
Re: [GMCnet] Honda ev4010 [message #207718 is a reply to message #207552] |
Tue, 14 May 2013 13:18 |
Ken Henderson
Messages: 8726 Registered: March 2004 Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
Tom,
Alan can scan & print 'most anything.
Ken H.
On May 13, 2013 12:05 PM, "Thomas Phipps" <tph1pp5@yahoo.com> wrote:
>
>
> For those of you who wish to install the Honda ev4010 GenSet with an
> undermount exhaust, I have a set of scanned images of the actual size unit
> mounting plate. Unfortunately, it is 12 scanned images. Unable to find a
> large size scanner in this no horse town.
> If Wal-Mart does not stock it, you cannot buy it.
> The file for the Honda ev6010 is on Billy's site. It will print actual
> size when printed on a large scale printer.
> Anyhow, P.M. me if you wish the set e-mailed to you.
>
> Tom, MS II
> --
> 1975 GMC Avion, under forever re-construction
> Vicksburg, MS. 3.7 miles from I-20
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
Re: [GMCnet] Honda EV4010 [message #303377 is a reply to message #207718] |
Sun, 10 July 2016 14:10 |
David Gardner
Messages: 62 Registered: June 2014
Karma: 0
|
Member |
|
|
> On Jul 10, 2016, at 11:16 AM, David Gardner wrote:
>
> Jeremy:
> I had a Honda 4000 put in my 23’ and had similar problems.
> 1. I’d check first to see that you don’t have a kink in your fuel line.
> 2. Does it run ok with the access door open, or does it shut down even when the door is open? That would help figuring out if you have enough air coming in to cool the generator.
>
> With mine I discovered I needed to put in another vent closer to the radiator, and that solved my problem, for a while. and then discovered that I had a kink in my supply line. Once I put in the extra vent, and found my kink, It has been running fine.
> Open the link below and you can see a picture of the additional vent I put in the generator door.
> Hope that helps.
>
> Dave Gardner
> 76 Birchaven 23’ “Chauncy”
> Mandalay Shores Ca
http://www.studiodavegardner.com/florida.html
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|