Anyone around NC area parting out a GMC? [message #190428] |
Thu, 15 November 2012 20:08 |
mojoe
Messages: 319 Registered: November 2012 Location: Monroe, NC
Karma: 0
|
Senior Member |
|
|
Looking for a few parts for my 1975 Eleganza project.
Close to Charlotte, NC would be great, or close by so shipping wont be so much.
Few parts as of now are:
propane and generator access doors. My are cracked and need repair
screens
engine hatch. mine is plywood would like aluminum
bumpers front and rear
black water tank. mine is cracked
window latches. just a couple
16" rims
refrigerator. propane/elect
maybe more later
Thanks!
Joe Kemenczky..
1975 Eleganza ll " Odie " 75,000 miles..
"When I was younger, I could remember anything, whether it had happened or not." - Mark Twain.
.
|
|
|
Re: Anyone around NC area parting out a GMC? [message #190465 is a reply to message #190428] |
Fri, 16 November 2012 09:04 |
|
Matt Colie
Messages: 8547 Registered: March 2007 Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
toyomojoe wrote on Thu, 15 November 2012 21:08 | Looking for a few parts for my 1975 Eleganza project.
Close to Charlotte, NC would be great, or close by so shipping wont be so much.
Few parts as of now are:
|
Did you know that about half the readers don't read the forum? They get it as e-mails or a digest, but those poor souls don't get the swap section
My responses to what you are looking to acquire.
propane and generator access doors. My are cracked and need repair - These are difficult to come by, but very easily repaired with epoxy and fiberglass.
screens - You need to be clear about what windows and for a 75 26'
engine hatch. mine is plywood would like aluminum - The OE are all plywood. Aluminum would be like a drum head - sound wise.
bumpers front and rear - You have a chance. If all you are looking for is good chrome, you might contact JimK.
black water tank. mine is cracked - These can be repaired.
window latches. just a couple - Scarce as hens teeth, but it is worthwhile to ask around
16" rims - If you want(can afford) alloy, talk to JimK. If you want steel, you can try to find used, check them for true and send them to a shop for blast and powder coat (mine ended up costing ~85$ ea when done) or (try to) order them new from Southwest wheel (~120$ea + shipping)
refrigerator. propane/elect - Not much chance on the used market. If you have one that does not work, you can get a new cooling unit for it for about half the price of new.
maybe more later - I hope they aren't big...
Thanks!
- Any time
Matt Colie
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
|
Re: Anyone around NC area parting out a GMC? [message #190490 is a reply to message #190428] |
Fri, 16 November 2012 15:22 |
A Hamilto
Messages: 4508 Registered: April 2011
Karma: 39
|
Senior Member |
|
|
toyomojoe wrote on Thu, 15 November 2012 20:08 | Looking for a few parts for my 1975 Eleganza project.
Close to Charlotte, NC would be great, or close by so shipping wont be so much.
Few parts as of now are:
propane and generator access doors. My are cracked and need repair
screens
engine hatch. mine is plywood would like aluminum
bumpers front and rear
black water tank. mine is cracked
window latches. just a couple
16" rims
refrigerator. propane/elect
maybe more later
Thanks!
| Is Richmond VA close enough? http://richmond.craigslist.org/rvs/3414147450.html
|
|
|