Home » Public Forums » GMCnet » [GMCnet] Door lock cylinder for '74 coach
| [GMCnet] Door lock cylinder for '74 coach [message #184325] |
Thu, 13 September 2012 15:17  |
ChrisW6ATV
Messages: 26
Registered: September 2005
Location: Hayward, California USA
Karma: 0
|
Junior Member |
|
|
Hello-
I had no luck with a locksmith regarding my Sequoia's broken lock cylinder, and I looked at a bunch of cylinders for GM doors and trunk lids at an auto parts store without finding anything usable. Should I start looking for an old cylinder from Jim K or Jim B perhaps, or so you have any other suggestions?
Thanks-
Chris Musselman
1974 Sequoia
Hayward, Cal.
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
|
|
|
|
| Re: [GMCnet] Door lock cylinder for '74 coach [message #184372 is a reply to message #184332] |
Thu, 13 September 2012 20:17  |
ChrisW6ATV
Messages: 26
Registered: September 2005
Location: Hayward, California USA
Karma: 0
|
Junior Member |
|
|
Gene-
Thank you for your reply. Yes, I had looked at your page and links, and I appreciate the information. From the "dwinchester" link, it appears that I may be able to just buy a new cylinder (or set of two) from a Kenworth dealer since my coach already has the smaller cylinder and key (I presume it was a Kenworth-type that was replaced/modified for a GM-type in later coaches).
Chris
>________________________________
> From: gene Fisher <mr.erfisher@gmail.com>
>
>
did you look through these links?
>http://gmcmotorhome.info/body.html#LATCH
>
>maybe some of these guys will know
>gene
>
>
>On Thu, Sep 13, 2012 at 1:17 PM, Christopher Musselman <rcoaster@pacbell.net
>> wrote:
>
>> Hello-
>>
>> I had no luck with a locksmith regarding my Sequoia's broken lock
>> cylinder, and I looked at a bunch of cylinders for GM doors and trunk lids
>> at an auto parts store without finding anything usable. Should I start
>> looking for an old cylinder from Jim K or Jim B perhaps, or so you have any
>> other suggestions?
>>
>>
>> Thanks-
>>
>> Chris Musselman
>> 1974 Sequoia
>> Hayward, Cal.
>
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
|
|
|
|
| Re: [GMCnet] Door lock cylinder for '74 coach [message #185321 is a reply to message #185309] |
Fri, 21 September 2012 20:32 |
Mr ERFisher
Messages: 7117
Registered: August 2005
Karma: 2
|
Senior Member |
|
|
any chance of a picture?
gene
On Fri, Sep 21, 2012 at 5:05 PM, Chris Musselman <rcoaster@pacbell.net>wrote:
> I brought my bad cylinder to the local Kenworth dealer, and they had the
> new ones in stock. It is just like the old one, except that I had to
> grind some of the flanges off each side where the slide-clip holds the
> cylinder to the door. The newer ones use a big snap ring that did not
> look like it could be used on the GMC. (Unless there is another Kenworth
> part that truly fits as is.) The part number for a set of two cylinders
> is 30GN15. They are not $22 or $30 for a set anymore, though; I paid
> just over $60 for the pair. (Some of that may be the normal
> "California/Bay Area tax", though.)
>
> Chris Musselman
> '74 Sequoia
> Hayward, Cal.
>
> On 9/13/2012 2:02 PM, gene Fisher wrote:
> > did you look through these links?
> > http://gmcmotorhome.info/body.html#LATCH
> >
> > maybe some of these guys will know
> > gene
> >
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Gene Fisher -- 74-23,77PB/ore/ca
“Give a man a fish; you have fed him for today --- give him a URL and
-------
http://gmcmotorhome.info/
Alternator Protection Cable
http://gmcmotorhome.info/APC.html
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: [GMCnet] Door lock cylinder for '74 coach [message #185369 is a reply to message #185321] |
Sat, 22 September 2012 02:09 |
ChrisW6ATV
Messages: 26
Registered: September 2005
Location: Hayward, California USA
Karma: 0
|
Junior Member |
|
|
Gene-
I already installed the new lock, but I can take side-by-side pictures
of the other, unmodified new lock with the original one, as well as the
hardware that came with the new one. Is that what you had in mind?
Chris
On 9/21/2012 6:32 PM, gene Fisher wrote:
> any chance of a picture?
> gene
>
>
> On Fri, Sep 21, 2012 at 5:05 PM, Chris Musselman <rcoaster@pacbell.net>wrote:
>
>> I brought my bad cylinder to the local Kenworth dealer, and they had the
>> new ones in stock. It is just like the old one, except that I had to
>> grind some of the flanges off each side where the slide-clip holds the
>> cylinder to the door. The newer ones use a big snap ring that did not
>> look like it could be used on the GMC. (Unless there is another Kenworth
>> part that truly fits as is.) The part number for a set of two cylinders
>> is 30GN15. They are not $22 or $30 for a set anymore, though; I paid
>> just over $60 for the pair. (Some of that may be the normal
>> "California/Bay Area tax", though.)
>>
>> Chris Musselman
>> '74 Sequoia
>> Hayward, Cal.
>>
>> On 9/13/2012 2:02 PM, gene Fisher wrote:
>>> did you look through these links?
>>> http://gmcmotorhome.info/body.html#LATCH
>>>
>>> maybe some of these guys will know
>>> gene
>>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>>
>
>
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: [GMCnet] Door lock cylinder for '74 coach [message #185371 is a reply to message #185369] |
Sat, 22 September 2012 03:01 |
Mr ERFisher
Messages: 7117
Registered: August 2005
Karma: 2
|
Senior Member |
|
|
hard for me to visualize, just wanted something for the next guy :>)
gene
On Sat, Sep 22, 2012 at 12:09 AM, Chris Musselman <rcoaster@pacbell.net>wrote:
> Gene-
>
> I already installed the new lock, but I can take side-by-side pictures
> of the other, unmodified new lock with the original one, as well as the
> hardware that came with the new one. Is that what you had in mind?
>
> Chris
>
> On 9/21/2012 6:32 PM, gene Fisher wrote:
> > any chance of a picture?
> > gene
> >
> >
> > On Fri, Sep 21, 2012 at 5:05 PM, Chris Musselman <rcoaster@pacbell.net
> >wrote:
> >
> >> I brought my bad cylinder to the local Kenworth dealer, and they had the
> >> new ones in stock. It is just like the old one, except that I had to
> >> grind some of the flanges off each side where the slide-clip holds the
> >> cylinder to the door. The newer ones use a big snap ring that did not
> >> look like it could be used on the GMC. (Unless there is another Kenworth
> >> part that truly fits as is.) The part number for a set of two cylinders
> >> is 30GN15. They are not $22 or $30 for a set anymore, though; I paid
> >> just over $60 for the pair. (Some of that may be the normal
> >> "California/Bay Area tax", though.)
> >>
> >> Chris Musselman
> >> '74 Sequoia
> >> Hayward, Cal.
> >>
> >> On 9/13/2012 2:02 PM, gene Fisher wrote:
> >>> did you look through these links?
> >>> http://gmcmotorhome.info/body.html#LATCH
> >>>
> >>> maybe some of these guys will know
> >>> gene
> >>>
> >> _______________________________________________
> >> GMCnet mailing list
> >> Unsubscribe or Change List Options:
> >> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
> >>
> >
> >
> >
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Gene Fisher -- 74-23,77PB/ore/ca
“Give a man a fish; you have fed him for today --- give him a URL and
-------
http://gmcmotorhome.info/
Alternator Protection Cable
http://gmcmotorhome.info/APC.html
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
|
|
| Re: [GMCnet] Door Lock [message #348486 is a reply to message #348484] |
Tue, 24 September 2019 11:47 |
emerystora
Messages: 4442
Registered: January 2004
Karma: 13
|
Senior Member |
|
|
The latch mechanism is, as Billy says, a Kenworth but it takes a GM tumbler. Any good locksmith can assist you or you might check Applied GMC or other GMC shops.
Emery Stora
77 Kingsley
Frederick CO
> On Tue, Sep 24, 2019 at 9:30 AM Billy Massey via Gmclist gmclist@list.gmcnet.org> wrote:
>
>> Tell em it's for a Kenworth
>>
>> bdub
>>
>>
>> On Tue, Sep 24, 2019, 11:16 AM Gary M via Gmclist >>
>> wrote:
>>
>>> I am trying to find a part number for a replacement door lock cylinder
>> for
>>> my 77 Royale. None of the parts houses around here can find one that
>>> matches the one currently in it. Any assistance would be great.
>>> --
>>> 77 Royale
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|
Goto Forum:
Current Time: Sat Sep 21 00:26:30 CDT 2024
Total time taken to generate the page: 0.02245 seconds
|
GMCforum
Search
Help
Register
Login
Home
