GMCforum: GMCnet » Onan Starter Hangs

Home » Public Forums » GMCnet » Onan Starter Hangs

Show: Today's Messages :: Polls :: Message Navigator

Onan Starter Hangs [message #170952]

Sun, 27 May 2012 09:23

2-4 the road

Messages: 145
Registered: June 2009
Location: Fulltimers

Karma: 0

Senior Member

Our Onan runs well but the new(5 months)starter
stays engaged sometimes. When it starts it
disengages ok. Won't quit with the stop button.
Thanks
Bill

2-4 the road 77 Kingsley 455

Report message to a moderator

Re: [GMCnet] Onan Starter Hangs [message #170954 is a reply to message #170952]

Sun, 27 May 2012 09:33

USAussie

Messages: 15912
Registered: July 2007
Location: Sydney, Australia

Karma: 6

Senior Member

Bill,

Double Trouble's Onan had the same problem and I removed the starter and
lubricated the shaft the gear that engages the flywheel rides on with
Valvoline Synpower and that cured the problem.

While you're removing the starter you can verify that the starter bracket
isn't broken, if it is get one a cast iron one from Ragusa.

http://www.ragusarv.com/

Click on Engine Items and it's the first part listed. It's P/N RV-04.

Regards,
Rob M.
�
-----Original Message-----
From: JoAnne Bissell

Our Onan runs well but the new(5 months)starter
stays engaged sometimes. When it starts it
disengages ok. Won't quit with the stop button.
Thanks
Bill

_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Regards, Rob M. (USAussie) The Pedantic Mechanic Sydney, Australia '75 Avion - AUS - The Blue Streak TZE365V100428 '75 Avion - USA - Double Trouble TZE365V100426

Report message to a moderator

Re: [GMCnet] Onan Starter Hangs [message #170955 is a reply to message #170954]

Sun, 27 May 2012 09:41

2-4 the road

Messages: 145
Registered: June 2009
Location: Fulltimers

Karma: 0

Senior Member

Thanks Rob. I will do that. BTW I bought and installed
one of JimK's starter mounts.
Bill

2-4 the road 77 Kingsley 455

Report message to a moderator

Re: [GMCnet] Onan Starter Hangs [message #170958 is a reply to message #170955]

Sun, 27 May 2012 09:56

emerystora

Messages: 4442
Registered: January 2004

Karma: 13

Senior Member

Bill

I have helped a couple of GMCers with the same problem. I felt it was an alignment problem My solution was to put a thin washer between one side of the starter and the Onan. This gives a little bit more clearance to allow the gear to retract.

Emery Stora

On May 27, 2012, at 8:41 AM, Bill and JoAnne Bissell <dad.bbissel1@gmail.com> wrote:

>
>
> Thanks Rob. I will do that. BTW I bought and installed
> one of JimK's starter mounts.
> Bill
> --
> 2-4 the road
> 77 Kingsley 455
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Report message to a moderator

Re: Onan Starter Hangs [message #171008 is a reply to message #170952]

Sun, 27 May 2012 20:02

Ernest Dankert

Messages: 133
Registered: May 2007
Location: Ogden, New York

Karma: 1

Senior Member

The electric choke on mine was disconnected when I bought it. I reattached the choke power and intermittently the starter would not electrically disengage. It would run with the starter relay would not disengage. I had to disconnect the power (heavy wire) to enable shut down of the onan. I disconnected the electric choke and it behaved. Never did figure what was wrong. I did substitute a different control board and traced the wires to insure there was no bare spots and pulled the flywheel to inspect the run armature.

View was not worth the climb. Juice not worth the squeeze.

1977 Eleganza II
Ogden NY

Report message to a moderator

Re: [GMCnet] Onan Starter Hangs [message #171017 is a reply to message #171008]

Sun, 27 May 2012 20:30

USAussie

Messages: 15912
Registered: July 2007
Location: Sydney, Australia

Karma: 6

Senior Member

Ernest,

You reminded me of something! I called Duane Simmons when the problem first
occurred and he told me to disconnect the electric choke and see what
happened. When I did that the problem stopped.

I left the choke wire disconnected and when it re-occurred that's when I
lubed the starter shaft and that corrected the problem the second time.

Duane explained what was causing the problem, however, since I didn't
remember the incident until your message I damn sure don't remember his
explanation! ;-)

Regards,
Rob M.
�
-----Original Message-----
From: Ernest Dankert

The electric choke on mine was disconnected when I bought it. I reattached
the choke power and intermittently the starter would not electrically
disengage. It would run with the starter relay would not disengage. I had to
disconnect the power (heavy wire) to enable shut down of the onan. I
disconnected the electric choke and it behaved. Never did figure what was
wrong. I did substitute a different control board and traced the wires to
insure there was no bare spots and pulled the flywheel to inspect the run
armature.

_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Regards, Rob M. (USAussie) The Pedantic Mechanic Sydney, Australia '75 Avion - AUS - The Blue Streak TZE365V100428 '75 Avion - USA - Double Trouble TZE365V100426

Report message to a moderator

Re: [GMCnet] Onan Starter Hangs [message #171035 is a reply to message #171017]

Sun, 27 May 2012 22:20

jimk

Messages: 6734
Registered: July 2006
Location: Belmont, CA

Karma: 9

Senior Member

Sometimes the starter rely needs to be replaced.

On Sun, May 27, 2012 at 6:30 PM, Robert Mueller <robmueller@iinet.net.au> wrote:
> Ernest,
>
> You reminded me of something! I called Duane Simmons when the problem first
> occurred and he told me to disconnect the electric choke and see what
> happened. When I did that the problem stopped.
>
> I left the choke wire disconnected and when it re-occurred that's when I
> lubed the starter shaft and that corrected the problem the second time.
>
> Duane explained what was causing the problem, however, since I didn't
> remember the incident until your message I damn sure don't remember his
> explanation! ;-)
>
> Regards,
> Rob M.
>
> -----Original Message-----
> From: Ernest Dankert
>
> The electric choke on mine was disconnected when I bought it. I reattached
> the choke power and intermittently the starter would not electrically
> disengage. It would run with the starter relay would not disengage. I had to
> disconnect the power (heavy wire) to enable shut down of the onan. I
> disconnected the electric choke and it behaved. Never did figure what was
> wrong. I did substitute a different control board and traced the wires to
> insure there was no bare spots and pulled the flywheel to inspect the run
> armature.
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

--
Jim Kanomata
Applied/GMC, Fremont,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502

Report message to a moderator

Previous Topic:	Maximum pressure for air bags???
Next Topic:	Selling my beloved Glenbrook

Goto Forum:

-=] Back to Top [=-

Current Time: Sun Nov 17 11:46:15 CST 2024

Total time taken to generate the page: 0.00911 seconds