Home » Public Forums » GMCnet » [GMCnet] New door handle
| [GMCnet] New door handle [message #146940] |
Tue, 18 October 2011 15:59  |
Richard Denney
Messages: 920
Registered: April 2010
Karma: 9
|
Senior Member |
|
|
Time for my quarterly drive-by posting.
We took Jaws to the Watermelon Park Bluegrass Festival, about the same time
you guys were at Goshen. This is an annual camping trip for us--and one the
Redhead enjoys in particular because it is attended by a large portion of
her circle of friends. It's quite a trek--maybe 25 whole miles from home.
But once again, the coach surprised me--everything just worked as it should.
I don't know why it continues to surprise me.
So, while there, the Redhead noted peeling chrome in a spot right in the
center of the door handle. It required careful placement of one's thumb to
avoid sharp-edged entanglements. And because the Redheard noted it, it had
to be replaced.
Also, as I was sliding the cockpit window closed after conferring with a
friend who was guiding me into place, the handle came off in my hand.
1. Door handle. After digging in Gene's site and looking at some referenced
pictures on the photo site, I ordered the correct Kenworth handle from a
supplier on eBay. Of course, it did not have the tab for the connection over
to the interior door handle, and I didn't really want to take the time to
cut it off the old one and weld it to the new one, so I drilled out the
rivets and used 3/16" stainless steel closed-end rivets with my Harbor
Freight air-powered riveter to move the old mechanism to the new handle. I
also moved the new springs to the old mechanism, which, along with a good
cleaning and some fresh lubrication really made it feel a lot newer.
My early coach has the stainless-steel plate that was a patch for the
original GM-designed door handle that didn't work reliably. It was held in
place with aluminum pop rivets, which didn't seem completely correct, and I
had the suspicion that it had been removed in the past. Sure enough--no
sealing whatsoever. When I removed the plate, there was all sorts of dirt
and evidence of leakage behind it, along with evidence of some leakage
inside the door. And the old gasket under the handle was a worthless sheet
of hard plastic. So, rather than cut a gasket, I installed the plate back on
the door and the handle to the plate with soft gaskets made from butyl
rubber. And I used the stainless rivets with it, too. All nice and new--took
40 minutes total. Those thinking this is a big job--just do it. The handle
makes a first impression. Do it at the same time you replace the door pin,
if you haven't already replaced that.
Question for all: Anybody have a GMC badge for that door patch they are
willing to part with? I didn't even realize that's what those two holes
(filled with rivets) were for until I saw the pictures.
2. Cockpit window handles/latches. These are held onto the window with
adhesive, and held in place while the adhesive sets with a couple of screws.
The reason I know the screws are not intended to be structural is a.) they
are small--maybe 6-32 threads, and b.) they are screwed into plastic (!)
dome-head nuts on the outside.
This did not seem to me adequate. Plus, I want to be able to remove these
for cleaning. So, I drilled out the #6 holes with a #10 drill bit and
installed stainless 10-24 dome-head screws, using a dome-head insert nut
that nestles with only a little play down into the hole in the glass. I used
a 1/4" sealing washer around the inserted portion of the nut to seal it.
Now, the handles are tight, the screws won't rust like the old ones did, and
it doesn't depend on glue that bakes in the sun for decades.
That's my life these days. GMC projects that take an hour, after having
waiting three months for some time to do it. But it was nice to push back
the forces of deterioration even if just a little bit.
Rick "hoping to make it to a rally next year for once" Denney
--
'73 230 "Jaws"
Northern Virginia
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: [GMCnet] New door handle [message #146950 is a reply to message #146940] |
Tue, 18 October 2011 16:51  |
Ken Henderson
Messages: 8726
Registered: March 2004
Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
Welcome home, Rick. We've missed you.
Ken H.
On Tue, Oct 18, 2011 at 4:59 PM, Richard Denney <rwdenney@gmail.com> wrote:
> Time for my quarterly drive-by posting.
> ,,,
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
|
| Re: [GMCnet] New door handle [message #147008 is a reply to message #146950] |
Tue, 18 October 2011 22:39 |
Richard Denney
Messages: 920
Registered: April 2010
Karma: 9
|
Senior Member |
|
|
On Tue, Oct 18, 2011 at 5:51 PM, Ken Henderson <hend4800@bellsouth.net>wrote:
> Welcome home, Rick. We've missed you.
>
It's good to be missed. I think about you guys a lot. I just don't have the
time any more to keep up with the list, and I don't really want to do so on
my "employer's" computer. But that doesn't mean I don't miss keeping up with
all of you.
I had thought I would be able to pace myself a bit, but I guess I'm just not
a pace-myself kind of guy.
The good news is that I've built my vacation time back up. There will be
more opportunities to go visiting next year, I hope.
The next batch of travel is getting ready to start, now that the fiscal year
is up and running again. Kansas City next week, New Hampshire the week after
that, followed by Texas, followed by Seattle. Then, a week in Texas to visit
family for Thanksgiving (we are driving, but not the coach--I'm sick of
airports). I get respect these days when I walk up to a United counter at
the airport, or at least I get as much respect as they are willing to give
anyone, which isn't much these days.
It felt good to undertake at least one decent project on the coach. I derive
tremendous satisfaction from the work that I'm doing, but I can enjoy that
without being happy about the effect it has had on my free time.
Rick "who has flown 70,000 miles so far this year, all of it domestic"
Denney
--
'73 230 "Jaws"
Northern Virginia
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: [GMCnet] New door handle [message #147021 is a reply to message #147008] |
Wed, 19 October 2011 01:57 |
Ken Burton
Messages: 10030
Registered: January 2004
Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
I was thinking about you just last week and wondering how you were doing.
This road warrior stuff can get tiresome very quickly. I spent many, many years on the road like you. After a while the cities all looked the same. Occasionally I would forget what city I was in.
Nice to hear from you. Come back when you can.
Ken B.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
|
Goto Forum:
Current Time: Mon Oct 07 00:19:58 CDT 2024
Total time taken to generate the page: 0.00505 seconds
|
GMCforum
Search
Help
Register
Login
Home
