GMCforum: GMCnet » [GMCnet] Grease Zerk Jig

Home » Public Forums » GMCnet » [GMCnet] Grease Zerk Jig

Show: Today's Messages :: Polls :: Message Navigator

[GMCnet] Grease Zerk Jig [message #121123]

Wed, 06 April 2011 18:22

Don Hart

Messages: 87
Registered: October 2009

Karma: 0

Member

Chuck

I just might be able to find a set around here if I look real hard.

Don
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Report message to a moderator

Re: [GMCnet] Grease Zerk Jig [message #121124 is a reply to message #121123]

Wed, 06 April 2011 18:42

C Boyd

Messages: 2629
Registered: April 2006

Karma: 18

Senior Member

Don Hart wrote on Wed, 06 April 2011 19:22

Don: as you know there is more than drilling the knuckles and installing the zerks. You also have to grind and drill the bearing race spacer and they are specific to the bearing set.
http://www.gmcmhphotos.com/photos/showphoto.php?photo=35711&title=grease-groves-and-hole&cat=5571
So bring new Timken set-23 bearings and seals.

C. Boyd
76 Crestmont
East Tennessee

Report message to a moderator

Re: [GMCnet] Grease Zerk Jig [message #121126 is a reply to message #121124]

Wed, 06 April 2011 18:57

Mr ERFisher

Messages: 7117
Registered: August 2005

Karma: 2

Senior Member

here is the definitive article on drilling the knuckles (being held hostage
by GMCMI;>)

http://goo.gl/N7sqF

and here is the article on the knuckle zerks
http://www.gmcmotorhome.info/front.html#ZERK

and pictures on how to use the jig
http://www.gmcmhphotos.com/photos/showphoto.php?photo=28898
or
http://goo.gl/x6Agc

good luck
gene

On Wed, Apr 6, 2011 at 4:42 PM, Charles Boyd <covered-wagon@comcast.net>wrote:

>
>
> Don Hart wrote on Wed, 06 April 2011 19:22
> > Chuck
> >
> > I just might be able to find a set around here if I look real hard.
> >
> > Don
> > _______________________________________________
> > GMCnet mailing list
> > Unsubscribe or Change List Options:
> > http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
>
>
>
>
>
>
> Don: as you know there is more than drilling the knuckles and installing
> the zerks. You also have to grind and drill the bearing race spacer and
> they are specific to the bearing set.
>
> http://www.gmcmhphotos.com/photos/showphoto.php?photo=35711&title=grease-groves-and-hole&cat=5571
> So bring new Timken set-23 bearings and seals.
> --
> C. Boyd
> 76 Crestmont by Midas
> East Tennessee
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>

--
Gene Fisher -- 74-23,77PB/ore/ca
�Give a man a fish; you have fed him for today --- give him a URL and
-------
http://gmcmotorhome.info/
Alternator Protection Cable
http://gmcmotorhome.info/APC.html
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Report message to a moderator

Previous Topic:	[GMCnet] Zerk Jig
Next Topic:	[GMCnet] Project '77, 26' in S TX

Goto Forum:

-=] Back to Top [=-

Current Time: Tue Nov 19 21:27:22 CST 2024

Total time taken to generate the page: 0.00945 seconds