Home » Public Forums » GMCnet » [GMCnet] Hubler Front end
| [GMCnet] Hubler Front end [message #114173] |
Fri, 04 February 2011 11:18  |
GMC_LES
Messages: 569
Registered: October 2009
Location: Montreal
Karma: 0
|
Senior Member |
|
|
Just wondering about the effects of the Hubler front hub upgrade on the Stock
GMC torsion bars. The way I see it, the Hubler mod moves the wheels outwards, as
well as the lower ball joint pivot point. this increases the lever effect of the
lower suspension arm on the torsion bar. This would result in additional forces
being appied to the stock torsion bar than wit hthe stock hubs. Is this of any
concern for our 35 year old bars?
Bill Hubler suggests using the 1 ton torsion bars which are shorter and larger
in diameter. This sounds like a good upgrade to include with the hubs, but I
would expect these bars to have an effect on ride quality and stiffness.
While on the Hubler subject, does anyone know if the bearing & seal can be
replaced on the 1-ton hub, or is it necessary to replace the complete hub as an
assy. A web search only shows the complete hubs but in Dan's blog, Jimk shows a
hub partially dismantled to show the bearing size differences. This leads me to
believe that a bearing replacement alone might be possible.
I'd like to hear opinions and experiences on this subject as it is a mod that I
am considering while my coach is in pieces.
Thanks,
Les Burt
Montreal
ELII in pieces
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Les Burt
Montreal
1975 Eleganza 26ft
A work in Progress
|
|
|
|
| Re: [GMCnet] Hubler Front end [message #114183 is a reply to message #114173] |
Fri, 04 February 2011 12:10  |
James Hupy
Messages: 6806
Registered: May 2010
Karma: -62
|
Senior Member |
|
|
I am familiar with the Chev & GMC 1 ton 4 wheel drive front hubs that the
Hubler front end is fashioned after. Yes the bearings can be replaced
separately, greased separately. I had a Chev 4 x 4 with an identical front
end and went 211,000 miles without any bearing issues and only one repack in
that time. If there is such a thing as a Bullet Proof front end system, this
is it. All still available over the counter.
Jim Hupy
Salem, Or
78 GMC Royale 403
On Fri, Feb 4, 2011 at 9:18 AM, Les Burt <burtco99@yahoo.com> wrote:
> Just wondering about the effects of the Hubler front hub upgrade on the
> Stock
> GMC torsion bars. The way I see it, the Hubler mod moves the
> wheels outwards, as
> well as the lower ball joint pivot point. this increases the lever effect
> of the
> lower suspension arm on the torsion bar. This would result in additional
> forces
> being appied to the stock torsion bar than wit hthe stock hubs. Is this of
> any
> concern for our 35 year old bars?
>
>
> Bill Hubler suggests using the 1 ton torsion bars which are shorter and
> larger
> in diameter. This sounds like a good upgrade to include with the hubs, but
> I
> would expect these bars to have an effect on ride quality and stiffness.
>
> While on the Hubler subject, does anyone know if the bearing & seal can be
> replaced on the 1-ton hub, or is it necessary to replace the complete hub
> as an
> assy. A web search only shows the complete hubs but in Dan's blog, Jimk
> shows a
> hub partially dismantled to show the bearing size differences. This leads
> me to
> believe that a bearing replacement alone might be possible.
>
> I'd like to hear opinions and experiences on this subject as it is a mod
> that I
> am considering while my coach is in pieces.
>
>
> Thanks,
> Les Burt
> Montreal
> ELII in pieces
>
>
>
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: [GMCnet] Hubler Front end [message #114186 is a reply to message #114173] |
Fri, 04 February 2011 12:40 |
Dave Mumert
Messages: 272
Registered: February 2004
Location: Olds, AB, Canada
Karma: 0
|
Senior Member |
|
|
Hi
Here is the Timken catalog that shows the part number and picture for the
GMC front hub.
http://www.timken.com/en-us/products/Documents/BSAC1990andNewerOrder7564.pdf
GMC replacement part number is on Page 103 (SP580310 looks to be the part)
The picture is on page 599 at the lower right. It is an integrated hub,
bearing and mount.
It is interesting that the SP580311 is listed as a replacement for the front
hub on both 4WD and RWD models.
Dave
> -----Original Message-----
> While on the Hubler subject, does anyone know if the bearing & seal can be
> replaced on the 1-ton hub, or is it necessary to replace the complete hub
as
> an assy. A web search only shows the complete hubs but in Dan's blog, Jimk
> shows a hub partially dismantled to show the bearing size differences.
This
> leads me to believe that a bearing replacement alone might be possible.
>
> I'd like to hear opinions and experiences on this subject as it is a mod
that I
> am considering while my coach is in pieces.
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
|
|
|
|
| Re: [GMCnet] Hubler Front end [message #114195 is a reply to message #114187] |
Fri, 04 February 2011 13:32 |
GMC_LES
Messages: 569
Registered: October 2009
Location: Montreal
Karma: 0
|
Senior Member |
|
|
I am sold on the fact that the 1-ton upgrade is the way to go. It has been on my
mind for some time.
I'm still waiting to hear & learn how this upgrade affects the torsion bars. My
only other concern would be availability of replacement lower arms should one
get damaged many years down the road.
This brings up another concern of mine:
As our Suppliers and Coachs age, I am expecting a continual decrease in parts
availability. We already know what it is like to own vehicles with parts that
are no longer made (Wallace hubs, Thermosan, and a long list of Factory parts)
In the best interests of all of us, I sure hope that our specialty suppliers
hand down or share the special production jigs and technical data for the "good
upgrades" to those willing to continue the support needed for survival of our
dinosaurs. To let the info die with it's originator is a shame as it pushes more
and more coaches into retirement.
Thanks,
Les Burt
Montreal
________________________________
From: Dan Gregg <gregg_dan@hotmail.com>
To: gmclist@temp.gmcnet.org
Sent: Fri, February 4, 2011 1:47:46 PM
Subject: Re: [GMCnet] Hubler Front end
If there is such a thing as a Bullet Proof front end system, this
is it. All still available over the counter.
Jim Hupy
Salem, Or
78 GMC Royale 403
[/quote]
Thank you Jim. That is why I wanted it. My plan was to get it in 08. But, had a
friend needing a frontend badly. So, he got the only one that was here at the
time. Now it is my turn.
I ran out and asked Alonzo about the bearing replacement but Jim answered faster
and better than I could have, Les.
I visited with Mr. Hubler at length back in 08 at Santa Rosa while he was
replacing a bearing on his. I saw no bearing tool was needed. Sold me right
there and then but I did not tell him that.
I will keep taking pictures and posting them on the blog. I also hope to take a
select few and put them up on Bdub's site for folks that come along later.
Dan
--
Dan & Teri Gregg
http://danandteri.blogspot.com/
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Les Burt
Montreal
1975 Eleganza 26ft
A work in Progress
|
|
|
|
| Re: [GMCnet] Hubler Front end [message #114197 is a reply to message #114189] |
Fri, 04 February 2011 13:51 |
 |
WD0AFQ
Messages: 7111
Registered: November 2004
Location: Dexter, Mo.
Karma: 207
|
Senior Member |
|
|
| Gerald Wheeler wrote on Fri, 04 February 2011 09:52 |
Dan writes: " So, he got the only one that was here at the time. Now it is
my turn."
So, is their a waiting list for the Hubler front end and if so, how long??
JR Wheeler NC/OR
|
I don't think so now, Jerry. These guys are too busy for me to bother right now. There are almost always 3 people on the phone here at one time. A very busy shop. Donny took today off so that slows things down also.
Back in 08, I believe that was the first Hubler that was installed by Donny and Alonzo. I was the one who broke the news to them why a certain coach was here. I had to run. They were not happy that they were about to install something for the first time. You know how big Donny is, I outran him even with my fused foot. 
Now, if you want one, when you come this month, you better call to make sure all of the parts are here.
Dan
3 In Stainless Exhaust Headers
One Ton All Discs/Reaction Arm
355 FD/Quad Bag/Alum Radiator Manny Tran/New eng.
Holley EFI/10 Tire Air Monitoring System
Solarized Coach/Upgraded Windows
Satelite TV/On Demand Hot Water/3Way Refer
|
|
|
|
| Re: [GMCnet] Hubler Front end [message #114201 is a reply to message #114195] |
Fri, 04 February 2011 14:03 |
ejuk8em
Messages: 90
Registered: July 2010
Karma: 0
|
Member |
|
|
I think I now understand the Hubler upgrade...sorta. Those of you who have gone this route, about how many $$$ are we talking about?
Lyle A. Rigdon, Retired Superintendent
'73 Pineapple Yellow Sequoia
Pawnee, IL 62558
Pawnee Pride - Live It!
--- On Fri, 2/4/11, Les Burt <burtco99@yahoo.com> wrote:
From: Les Burt <burtco99@yahoo.com>
Subject: Re: [GMCnet] Hubler Front end
To: gmclist@temp.gmcnet.org
Date: Friday, February 4, 2011, 1:32 PM
I am sold on the fact that the 1-ton upgrade is the way to go. It has been on my
mind for some time.
I'm still waiting to hear & learn how this upgrade affects the torsion bars. My
only other concern would be availability of replacement lower arms should one
get damaged many years down the road.
This brings up another concern of mine:
As our Suppliers and Coachs age, I am expecting a continual decrease in parts
availability. We already know what it is like to own vehicles with parts that
are no longer made (Wallace hubs, Thermosan, and a long list of Factory parts)
In the best interests of all of us, I sure hope that our specialty suppliers
hand down or share the special production jigs and technical data for the "good
upgrades" to those willing to continue the support needed for survival of our
dinosaurs. To let the info die with it's originator is a shame as it pushes more
and more coaches into retirement.
Thanks,
Les Burt
Montreal
________________________________
From: Dan Gregg <gregg_dan@hotmail.com>
To: gmclist@temp.gmcnet.org
Sent: Fri, February 4, 2011 1:47:46 PM
Subject: Re: [GMCnet] Hubler Front end
If there is such a thing as a Bullet Proof front end system, this
is it. All still available over the counter.
Jim Hupy
Salem, Or
78 GMC Royale 403
[/quote]
Thank you Jim. That is why I wanted it. My plan was to get it in 08. But, had a
friend needing a frontend badly. So, he got the only one that was here at the
time. Now it is my turn.
I ran out and asked Alonzo about the bearing replacement but Jim answered faster
and better than I could have, Les.
I visited with Mr. Hubler at length back in 08 at Santa Rosa while he was
replacing a bearing on his. I saw no bearing tool was needed. Sold me right
there and then but I did not tell him that.
I will keep taking pictures and posting them on the blog. I also hope to take a
select few and put them up on Bdub's site for folks that come along later.
Dan
--
Dan & Teri Gregg
http://danandteri.blogspot.com/
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
|
|
| Re: [GMCnet] Hubler Front end [message #114210 is a reply to message #114201] |
Fri, 04 February 2011 14:57 |
 |
USAussie
Messages: 15912
Registered: July 2007
Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
Lyle,
Here you go:
http://www.appliedgmc.com/prod.itml/icOid/635
Regards,
Rob M.
USAussie - Downunder
AUS '75 Avion - The Blue Streak TZE365V100428
USA '75 Avion - Double Trouble TZE365V100426
-----Original Message-----
From: gmclist-bounces@temp.gmcnet.org
[mailto:gmclist-bounces@temp.gmcnet.org] On Behalf Of Lyle A. Rigdon
Sent: Saturday, February 05, 2011 7:03 AM
To: gmclist@temp.gmcnet.org
Subject: Re: [GMCnet] Hubler Front end
I think I now understand the Hubler upgrade...sorta. Those of you who have
gone this route, about how many $$$ are we talking about?
Lyle A. Rigdon, Retired Superintendent
'73 Pineapple Yellow Sequoia
Pawnee, IL 62558
Pawnee Pride - Live It!
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
|
| Re: [GMCnet] Hubler Front end [message #114213 is a reply to message #114201] |
Fri, 04 February 2011 15:26 |
jimk
Messages: 6734
Registered: July 2006
Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
Les,
Were finding that the location of the wheel does not seem to cause the
coach to lower bit 3/8 of an inch.
When we do the 2" spacer it is again 1/8-1/4.
The original torsion bar seems to work well and not effect the ride.
Keep in mind, the lower A frame has been rebuilt and the torsion bar
socket is now reinforced on 360 degrees.
There are several things not mentioned or discussed that one need to
know, or face it later.
The bearing comes as a complete unit which we can sell for $200 per side.
If you pay a person to take it apart and screw it up, your wasting your time.
On Fri, Feb 4, 2011 at 12:03 PM, Lyle A. Rigdon <ejuk8em@yahoo.com> wrote:
> I think I now understand the Hubler upgrade...sorta. Those of you who have gone this route, about how many $$$ are we talking about?
>
>
> Lyle A. Rigdon, Retired Superintendent
> '73 Pineapple Yellow Sequoia
> Pawnee, ILÂ 62558
> Pawnee Pride - Live It!
>
> --- On Fri, 2/4/11, Les Burt <burtco99@yahoo.com> wrote:
>
>
> From: Les Burt <burtco99@yahoo.com>
> Subject: Re: [GMCnet] Hubler Front end
> To: gmclist@temp.gmcnet.org
> Date: Friday, February 4, 2011, 1:32 PM
>
>
> I am sold on the fact that the 1-ton upgrade is the way to go. It has been on my
> mind for some time.
> I'm still waiting to hear & learn how this upgrade affects the torsion bars. My
> only other concern would be availability of replacement lower arms should one
> get damaged many years down the road.
>
>
> This brings up another concern of mine:
> Â As our Suppliers and Coachs age, I am expecting a continual decrease in parts
> availability. We already know what it is like to own vehicles with parts that
> are no longer made (Wallace hubs, Thermosan, and a long list of Factory parts)
>
> In the best interests of all of us, I sure hope that our specialty suppliers
> hand down or share the special production jigs and technical data for the "good
> upgrades" to those willing to continue the support needed for survival of our
> dinosaurs. To let the info die with it's originator is a shame as it pushes more
> and more coaches into retirement.
>
>
> Thanks,
> Les Burt
> Montreal
>
>
>
>
> ________________________________
> From: Dan Gregg <gregg_dan@hotmail.com>
> To: gmclist@temp.gmcnet.org
> Sent: Fri, February 4, 2011 1:47:46 PM
> Subject: Re: [GMCnet] Hubler Front end
>
>
>
>
> If there is such a thing as a Bullet Proof front end system, this
> is it. All still available over the counter.
> Jim Hupy
> Salem, Or
> 78 GMC Royale 403
>
>
>
> [/quote]
>
> Thank you Jim. That is why I wanted it. My plan was to get it in 08. But, had a
> friend needing a frontend badly. So, he got the only one that was here at the
> time. Now it is my turn.
> I ran out and asked Alonzo about the bearing replacement but Jim answered faster
> and better than I could have, Les.
> I visited with Mr. Hubler at length back in 08 at Santa Rosa while he was
> replacing a bearing on his. I saw no bearing tool was needed. Sold me right
> there and then but I did not tell him that.
> I will keep taking pictures and posting them on the blog. I also hope to take a
> select few and put them up on Bdub's site for folks that come along later.
> Dan
> --
> Dan & Teri Gregg
>
> http://danandteri.blogspot.com/
>
>
>
>
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
>
>
>
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Jim Kanomata
Applied/GMC, Fremont,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
|
|
|
| Re: [GMCnet] Hubler Front end [message #114217 is a reply to message #114173] |
Fri, 04 February 2011 16:05 |
g.winger
Messages: 792
Registered: February 2008
Location: Warrenton,Missouri
Karma: 0
|
Senior Member |
|
|
|
I love mine,especialy the 12" brakes. Now about the cost. IF you need it all done,,,,the Hubler front end is LESS than having original GMC parts. Go to Jims site and add up both, you'll see. Also there have been a bunch of posts on this before. Go to the "list every post" of mine and scroll down,,,you'll find it. My advice,,,,get it,,,,,PL
|
|
|
|
| Re: [GMCnet] Hubler Front end [message #114227 is a reply to message #114213] |
Fri, 04 February 2011 17:30 |
GMC_LES
Messages: 569
Registered: October 2009
Location: Montreal
Karma: 0
|
Senior Member |
|
|
Thanks Jim, that was about what I expected to hear in terms of how it affects ride height.
Regarding the 1-ton hubs, I agree that it isn't worth it for most people to consider rebuilding them. If is nice to know that they can be taken apart if desired.
Since the hubler front end uses larger and readily available brake discs, has anyone considered using the same discs in the rear with the reaction arm system? I would think it would be more advantageous just due to not needing a specially modified disc for the rear. The additional diameter isn't needed but is still a welcome advantage. The reaction arm system requires custom brackets and spacers, so just some small dimensional changes should be all that is required to accommodate the 1-ton discs in the rear.
Les Burt
Sent from my iPhone
On 2011-02-04, at 4:26 PM, Jim Kanomata <jimkanomata@gmail.com> wrote:
> Les,
> Were finding that the location of the wheel does not seem to cause the
> coach to lower bit 3/8 of an inch.
> When we do the 2" spacer it is again 1/8-1/4.
> The original torsion bar seems to work well and not effect the ride.
> Keep in mind, the lower A frame has been rebuilt and the torsion bar
> socket is now reinforced on 360 degrees.
> There are several things not mentioned or discussed that one need to
> know, or face it later.
> The bearing comes as a complete unit which we can sell for $200 per side.
> If you pay a person to take it apart and screw it up, your wasting your time.
>
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Les Burt
Montreal
1975 Eleganza 26ft
A work in Progress
|
|
|
|
| Re: [GMCnet] Hubler Front end [message #114230 is a reply to message #114217] |
Fri, 04 February 2011 17:51 |
storm'n
Messages: 492
Registered: April 2007
Location: Ont. Can
Karma: 0
|
Senior Member |
|
|
I have a question. Is the CV joint the same as OE or is it the 1T.
CV.
Thanks
Norm
--- On Fri, 2/4/11, Paul Leavitt <leavittpaul@yahoo.com> wrote:
I love mine,especialy the 12" brakes. Now about the cost. IF you need it all done,,,,the Hubler front end is LESS than having original GMC parts. Go to Jims site and add up both, you'll see. Also there have been a bunch of posts on this before. Go to the "list every post" of mine and scroll down,,,you'll find it. My advice,,,,get it,,,,,PL
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: [GMCnet] Hubler Front end [message #114241 is a reply to message #114213] |
Fri, 04 February 2011 18:49 |
Ken Henderson
Messages: 8726
Registered: March 2004
Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
Jim,
I've heard but forgotten, does the Hubler kit increase available caster,
even without offset bushings?
Ken H.
On Fri, Feb 4, 2011 at 4:26 PM, Jim Kanomata <jimkanomata@gmail.com> wrote:
> Les,
> Were finding that the location of the wheel does not seem to cause the
> coach to lower bit 3/8 of an inch.
> When we do the 2" spacer it is again 1/8-1/4.
> The original torsion bar seems to work well and not effect the ride.
> Keep in mind, the lower A frame has been rebuilt and the torsion bar
> socket is now reinforced on 360 degrees.
> There are several things not mentioned or discussed that one need to
> know, or face it later.
> The bearing comes as a complete unit which we can sell for $200 per side.
> If you pay a person to take it apart and screw it up, your wasting your
> time.
>
>
>
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
|
|
|
| Re: [GMCnet] Hubler Front end [message #114246 is a reply to message #114227] |
Fri, 04 February 2011 19:51 |
|
USAussie
Messages: 15912
Registered: July 2007
Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
Les,
Here's a link to Leigh Harrison's large diameter middle axle brake disk kit:
http://www.leighharrisongmcmotorhomeupgrades.com/CenterAxleDiscBrakeKit.html
I have Caddy disks on my middle axles and OEM drums on the rear.
Regards,
Rob M.
USAussie - Downunder
AUS '75 Avion - The Blue Streak TZE365V100428
USA '75 Avion - Double Trouble TZE365V100426
-----Original Message-----
From: gmclist-bounces@temp.gmcnet.org
[mailto:gmclist-bounces@temp.gmcnet.org] On Behalf Of Les Burt
Sent: Saturday, February 05, 2011 10:31 AM
To: gmclist@temp.gmcnet.org
Subject: Re: [GMCnet] Hubler Front end
Thanks Jim, that was about what I expected to hear in terms of how it
affects ride height.
Regarding the 1-ton hubs, I agree that it isn't worth it for most people to
consider rebuilding them. If is nice to know that they can be taken apart if
desired.
Since the hubler front end uses larger and readily available brake discs,
has anyone considered using the same discs in the rear with the reaction arm
system? I would think it would be more advantageous just due to not needing
a specially modified disc for the rear. The additional diameter isn't needed
but is still a welcome advantage. The reaction arm system requires custom
brackets and spacers, so just some small dimensional changes should be all
that is required to accommodate the 1-ton discs in the rear.
Les Burt
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
|
| Re: [GMCnet] Hubler Front end [message #114252 is a reply to message #114227] |
Fri, 04 February 2011 20:15 |
jimk
Messages: 6734
Registered: July 2006
Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
Les,
The reactionarm system is so good that there is no real advantage to
using a bigger rotor.
Some havealmost put flat spots on the front tires.
I could not believe what the reaction arm does till we started doing
live tests here.
On Fri, Feb 4, 2011 at 3:30 PM, Les Burt <burtco99@yahoo.com> wrote:
> Thanks Jim, that was about what I expected to hear in terms of how it affects ride height.
>
> Regarding the 1-ton hubs, I agree that it isn't worth it for most people to consider rebuilding them. If is nice to know that they can be taken apart if desired.
>
> Since the hubler front end uses larger and readily available brake discs, has anyone considered using the same discs in the rear with the reaction arm system? I would think it would be more advantageous just due to not needing a specially modified disc for the rear. The additional diameter isn't needed but is still a welcome advantage. The reaction arm system requires custom brackets and spacers, so just some small dimensional changes should be all that is required to accommodate the 1-ton discs in the rear.
>
> Les Burt
> Sent from my iPhone
>
> On 2011-02-04, at 4:26 PM, Jim Kanomata <jimkanomata@gmail.com> wrote:
>
>> Les,
>> Were finding that the location of the wheel does not seem to cause the
>> coach to lower bit 3/8 of an inch.
>> When we do the 2" spacer it is again 1/8-1/4.
>> The original torsion bar seems to work well and not effect the ride.
>> Keep in mind, the lower A frame has been rebuilt and the torsion bar
>> socket is now reinforced on 360 degrees.
>> There are several things not mentioned or discussed that one need to
>> know, or face it later.
>> The bearing comes as a complete unit which we can sell for $200 per side.
>> If you pay a person to take it apart and screw it up, your wasting your time.
>>
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Jim Kanomata
Applied/GMC, Fremont,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
|
| Re: [GMCnet] Hubler Front end [message #114253 is a reply to message #114246] |
Fri, 04 February 2011 20:17 |
GMC_LES
Messages: 569
Registered: October 2009
Location: Montreal
Karma: 0
|
Senior Member |
|
|
Rob,
The Harrison big brakes were sort of what I had in mind, but combined with the advantage of the reaction arm.
Most of the reaction arm braking system components are custom made. Even the discs are specially modified for the application, so replacements are only available from a very few sources. From what I can tell, only a few dimensional changes would be required to permit use of an off the shelf disc such as the 1-ton 4x4 front disc that is used in the Hubler upgrade. For some of the same reasons that the Hubler kit is a smart upgrade, I think having an easily obtainable disc for the rear is a worthwhile effort to pursue.
If we are going to discuss this further, it deserves a separate thread so the info doesn't get lost.
Les Burt
Sent from my iPhone
On 2011-02-04, at 8:51 PM, "Rob Mueller" <robmueller@iinet.net.au> wrote:
> Les,
>
> Here's a link to Leigh Harrison's large diameter middle axle brake disk kit:
>
> http://www.leighharrisongmcmotorhomeupgrades.com/CenterAxleDiscBrakeKit.html
>
> I have Caddy disks on my middle axles and OEM drums on the rear.
>
> Regards,
> Rob M.
> USAussie - Downunder
> AUS '75 Avion - The Blue Streak TZE365V100428
> USA '75 Avion - Double Trouble TZE365V100426
>
>
> -----Original Message-----
> From: gmclist-bounces@temp.gmcnet.org
> [mailto:gmclist-bounces@temp.gmcnet.org] On Behalf Of Les Burt
> Sent: Saturday, February 05, 2011 10:31 AM
> To: gmclist@temp.gmcnet.org
> Subject: Re: [GMCnet] Hubler Front end
>
> Thanks Jim, that was about what I expected to hear in terms of how it
> affects ride height.
>
> Regarding the 1-ton hubs, I agree that it isn't worth it for most people to
> consider rebuilding them. If is nice to know that they can be taken apart if
> desired.
>
> Since the hubler front end uses larger and readily available brake discs,
> has anyone considered using the same discs in the rear with the reaction arm
> system? I would think it would be more advantageous just due to not needing
> a specially modified disc for the rear. The additional diameter isn't needed
> but is still a welcome advantage. The reaction arm system requires custom
> brackets and spacers, so just some small dimensional changes should be all
> that is required to accommodate the 1-ton discs in the rear.
>
> Les Burt
>
>
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Les Burt
Montreal
1975 Eleganza 26ft
A work in Progress
|
|
|
|
Goto Forum:
Current Time: Wed Nov 06 00:42:25 CST 2024
Total time taken to generate the page: 0.01125 seconds
|
GMCforum
Search
Help
Register
Login
Home
