| Kitchen faucet needed? [message #95374] |
Wed, 11 August 2010 18:07  |
C Boyd
Messages: 2629
Registered: April 2006
Karma: 18
|
Senior Member |
|
|
I need a replacement faucet for an Eleganza II. I would like tall faucet to set pots under. Anyone have ideas??
C. Boyd
76 Crestmont
East Tennessee
|
|
|
|
| Re: Kitchen faucet needed? [message #95376 is a reply to message #95374] |
Wed, 11 August 2010 18:26  |
Dr. Olds
Messages: 4
Registered: August 2010
Karma: 0
|
Junior Member |
|
|
| C Boyd wrote on Wed, 11 August 2010 18:07 |
I need a replacement faucet for an Eleganza II. I would like tall faucet to set pots under. Anyone have ideas??
|
I am the one needing the faucet. Mary Mondello
Joe Mondello
75 Eleganza II
Crossville, Tennessee
|
|
|
|
|
|
| Re: [GMCnet] Kitchen faucet needed? [message #95400 is a reply to message #95381] |
Wed, 11 August 2010 20:38 |
jimk
Messages: 6734
Registered: July 2006
Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
Try putting them in without making a large hole.
On Wed, Aug 11, 2010 at 4:49 PM, Dwayne Jacobson
<dwayne@havenproperties.ca>wrote:
> Go to Home Depot or something like that and buy a residential faucet - with
> a long neck
> Dwayne Jacobson
> 77 Eleganza II
> White Rock
>
> -----Original Message-----
> From: gmclist-bounces@temp.gmcnet.org
> [mailto:gmclist-bounces@temp.gmcnet.org] On Behalf Of Joe Mondello
> Sent: Wednesday, August 11, 2010 4:26 PM
> To: gmclist@temp.gmcnet.org
> Subject: Re: [GMCnet] Kitchen faucet needed?
>
>
>
> C Boyd wrote on Wed, 11 August 2010 18:07
> > I need a replacement faucet for an Eleganza II. I would like tall faucet
> to set pots under. Anyone have ideas??
>
>
>
>
>
>
>
>
>
> I am the one needing the faucet. Mary Mondello
>
> --
> Joe Mondello
> 75 Eleganza II
> Crossville, Tennessee
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Jim Kanomata
Applied/GMC, Fremont,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
|
|
|
|
|
|
|
| Re: Kitchen faucet needed? [message #95416 is a reply to message #95405] |
Wed, 11 August 2010 21:23 |
Dr. Olds
Messages: 4
Registered: August 2010
Karma: 0
|
Junior Member |
|
|
| wally wrote on Wed, 11 August 2010 20:56 |
| Dr. Olds wrote on Wed, 11 August 2010 18:26 |
| C Boyd wrote on Wed, 11 August 2010 18:07 |
I need a replacement faucet for an Eleganza II. I would like tall faucet to set pots under. Anyone have ideas??
|
I am the one needing the faucet. Mary Mondello
|
We put in a Delta 182-SS like this
http://www.amazon.com/Delta-182-SS-Verona-Stainless-Kitchen/dp/B001BSJNXK
JWID
|
What does JWID mean? Joe used his calipers to measure the OD of the threaded pipe on the original faucet and it is 1-3/16. We were told that Moen (the original faucets manufacturer)has a one hole installation faucet available but the one I purchesed from Lowes didn't work. Also, it isn't a goose neck and that's what we need. . .all Joe's big pasta pots, you know! I have attached a photo of the original after we removed it from the sink. The new one that didn't work is in the pic also.
Joe Mondello
75 Eleganza II
Crossville, Tennessee
|
|
|
|
|
|
|
|
| Re: Kitchen faucet needed? [message #95422 is a reply to message #95419] |
Wed, 11 August 2010 21:46 |
C Boyd
Messages: 2629
Registered: April 2006
Karma: 18
|
Senior Member |
|
|
JWID = just what I did....
Mary: I think I left a white ring binder ( factory service bulletins) at the shop. Please ask Joe to hang on to it till I get back.
C. Boyd
76 Crestmont
East Tennessee
|
|
|
|
|
|
| Re: Kitchen faucet needed? [message #95711 is a reply to message #95416] |
Fri, 13 August 2010 17:01 |
roy1
Messages: 2126
Registered: July 2004
Location: Minden nevada
Karma: 6
|
Senior Member |
|
|
Mary
The faucet I have is a Moen. It looks kinda like the one Dennis has except it is a fixed nozzle (no hose that comes out of the head) I remember it came with a large mounting plate which I couldn't use. The store had an adapter ring (home depot)
that they sold separately so it could be mounted in the single hole and you then discard the metal plate. If you look closely at the photo Dennis posted you can see the adapter ring at the bottom of his faucet. This little metal type ring or washer will convert single type faucets for 1 hole instillation rather then 2 hole installation with the metal plate.
Roy
Roy Keen
Minden,NV
76 X Glenbrook
|
|
|
|
GMCforum
Search
Help
Register
Login
Home
