Home » Public Forums » GMCnet » Hamilton (Ohio) Work Rally
| Hamilton (Ohio) Work Rally [message #84895] |
Sun, 16 May 2010 23:14  |
Ken Burton
Messages: 10030
Registered: January 2004
Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
Well, I just got home from the Dayton Hamfest. While I was there I met with both Jim Millers (Junior and Senior) several times. One of their GMCs is always parked in two of the 2500 or so available flea market spots.
Jim Senior asked me to please spread word that you can arrive for the work rally on any day and stay as long as you wish. I believe the announcement only stated next Friday and Saturday.
You are welcome to come and spend the week, or the week end, or as many days as you have available. I'm headed back down there next Wednesday.
So come on over to Hamiliton this week and enjoy a good time.
WiFi service will be provided by Jim Miller. 110 volt power is available.
No club affiliations. No dues. Just show up and bring your favorite GMC work project that you wish to work on.
We will also have a set of scales available.
If I remember to bring it, there will be A/C gauges, vacuum pump, and some Duracool.
I also plan at least one visit to my favorite Cincinnati junk yard. Jim Sr. says he also has another one to go visit that is much closer.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
|
| Re: Hamilton (Ohio) Work Rally [message #84899 is a reply to message #84895] |
Mon, 17 May 2010 04:17  |
Jim Galbavy
Messages: 1443
Registered: August 2007
Karma: 7
|
Senior Member |
|
|
Ken,
When you see them this week, please tell the Millers "Hey" for me and thank you. They are three special people, I only wish we could see them more often. Great folks.
Ya'll have a great rally. I'll be with THE CRABS at our opener for this season.
jim galbavy
'73 X-CL (ANNIE)
Chesterfield, Va
[Updated on: Mon, 17 May 2010 04:18] Report message to a moderator |
|
|
|
| Re: [GMCnet] Hamilton (Ohio) Work Rally [message #84931 is a reply to message #84899] |
Mon, 17 May 2010 09:50 |
Sandra Price
Messages: 709
Registered: May 2006
Karma: 1
|
Senior Member |
|
|
Where are you with "The Crabs"? We're in Maryland and might want to check
out what's going on.
Sandra and Bob Price
On Mon, May 17, 2010 at 4:17 AM, Jim Galbavy <j.galbavy@att.net> wrote:
>
>
> Ken,
>
> When you see them this week, please tell the Millers "Hey" for me and thank
> you. They are three special people, I only wish we could see them more
> often. Great folks.
>
> Ya'll have a great rally. I'll with THE CRABS at our opener for this
> season.
>
> jim galbavy
> '73 X-CL (ANNIE)
> Chesterfield, Va
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
IN GOD WE TRUST!
Sandra and Bob in the 51st Year of our State of Marriage
“Life’s a Trip” in “The Roadhouse”
’73 Painted Desert
Huntsville, TX
Finally, all of you, live in harmony with one another, be sympathetic, love
as brothers, be compassionate and humble. Do not repay evil with evil or
insult with insult, but with blessing, because to this you were called so
that you may inherit a blessing. --1 Peter 3:8-9
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
|
|
| Re: [GMCnet] Hamilton (Ohio) Work Rally [message #84967 is a reply to message #84932] |
Mon, 17 May 2010 12:30 |
|
|
I guess this means we don't have to buy ice cream. Big Jim was wondering. He
didn't want any complaints this year from a certain social butterfly who
shall remain anonymous.
We'll still miss you.
Byron Songer
1978 Royale by Coachmen
Louisville, KY
Personal - http://web.me.com/bnsonger
Eastern States - http://www.gmceast.com
Dan Gregg wrote:
>
>
> I must say that this is one great gathering. I was there last year and we had
> an absolute blast. there are no more gracious hosts than the 3 Millers. It was
> obvioust to me that they just love having folks gather on their property. We
> had a pit available last year too. Any chore that can be done in a couple of
> days is not too large. Just let folks know in advance wo help can be lined up.
> Bob Burkitt is close and he is a very gracious guy. Last year he brought his
> coach for Ken and me to sleep in.
> You will not attend a better, small, gathering.
> Dan
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
--
Byron Songer
Full-timing to enjoy the USA
Former owner but still an admirer
GMC paint schemes at -
http://www.songerconsulting.net
|
|
|
|
| Re: Hamilton (Ohio) Work Rally [message #84975 is a reply to message #84899] |
Mon, 17 May 2010 13:21 |
Ken Burton
Messages: 10030
Registered: January 2004
Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
| Jim Galbavy wrote on Mon, 17 May 2010 04:17 |
Ken,
When you see them this week, please tell the Millers "Hey" for me and thank you. They are three special people, I only wish we could see them more often. Great folks.
Ya'll have a great rally. I'll be with THE CRABS at our opener for this season.
jim galbavy
'73 X-CL (ANNIE)
Chesterfield, Va
|
To bad you can not make it. If you have a change a plans, you can always show up in Hamilton.
Ken
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
|
| Re: Hamilton (Ohio) Work Rally [message #85020 is a reply to message #84895] |
Mon, 17 May 2010 20:59 |
Ken Burton
Messages: 10030
Registered: January 2004
Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
OK. For whomever asked, Today I went to the airport and picked up the scales and torsion bar unloader tool. They are now in my pickup and will be at Hamilton.
I have a request. I know I supplied the ride height distances between the BOTTOM OF THE FRAME and the ground here on two occasions inthe past. I do not have those numbers at the moment. I could use them now so I can cut some measuring blocks tonight.
Anyone one out there have the numbers available?
Ken B.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
|
|
|
| Re: [GMCnet] Hamilton (Ohio) Work Rally [message #85033 is a reply to message #85029] |
Mon, 17 May 2010 22:05 |
Ken Burton
Messages: 10030
Registered: January 2004
Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
| k2gkk wrote on Mon, 17 May 2010 21:34 |
From my 1976 supplement:
Front: 13 1/8" +/- 1/4"
Rear : 11 1/16" +/- 1.4"
Both measured from ground to elongated slots
on the frame rails.
You'll have to subtract the distance between
those slots and the bottom of the frame to get
the correct height for the blocks.
* Mac Macdonald *
* Oklahoma City *
** "Money Pit" **
* '76 ex - P.B. *
----------------------------------------
> To: gmclist@temp.gmcnet.org
> From: n9cv@comcast.net
> Date: Mon, 17 May 2010 20:59:15 -0500
> Subject: Re: [GMCnet] Hamilton (Ohio) Work Rally
>
>
>
> OK. For whomever asked, Today I went to the airport and picked up the scales and torsion bar unloader tool. They are now in my pickup and will be at Hamilton.
>
> I have a request. I know I supplied the ride height distances between the BOTTOM OF THE FRAME and the ground here on two occasions inthe past. I do not have those numbers at the moment. I could use them now so I can cut some measuring blocks tonight.
>
> Anyone one out there have the numbers available?
>
>
> Ken B.
>
>
> --
> Ken Burton - N9KB
> 76 Palm Beach
> Hebron, Indiana
|
Thanks. I have those numbers. I need the numbers from the bottom of the frame. I had some blocks cut but gave them away. I am not near a coach to measure the difference between the holes in the frame and the bottom of the frame.
Ken B.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
|
| Re: [GMCnet] Hamilton (Ohio) Work Rally [message #85048 is a reply to message #85033] |
Mon, 17 May 2010 23:34 |
Ken Burton
Messages: 10030
Registered: January 2004
Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
| Ken Burton wrote on Mon, 17 May 2010 22:05 |
| k2gkk wrote on Mon, 17 May 2010 21:34 |
From my 1976 supplement:
Front: 13 1/8" +/- 1/4"
Rear : 11 1/16" +/- 1.4"
Both measured from ground to elongated slots
on the frame rails.
You'll have to subtract the distance between
those slots and the bottom of the frame to get
the correct height for the blocks.
* Mac Macdonald *
* Oklahoma City *
** "Money Pit" **
* '76 ex - P.B. *
----------------------------------------
> To: gmclist@temp.gmcnet.org
> From: n9cv@comcast.net
> Date: Mon, 17 May 2010 20:59:15 -0500
> Subject: Re: [GMCnet] Hamilton (Ohio) Work Rally
>
>
>
> OK. For whomever asked, Today I went to the airport and picked up the scales and torsion bar unloader tool. They are now in my pickup and will be at Hamilton.
>
> I have a request. I know I supplied the ride height distances between the BOTTOM OF THE FRAME and the ground here on two occasions inthe past. I do not have those numbers at the moment. I could use them now so I can cut some measuring blocks tonight.
>
> Anyone one out there have the numbers available?
>
>
> Ken B.
>
>
> --
> Ken Burton - N9KB
> 76 Palm Beach
> Hebron, Indiana
|
Thanks. I have those numbers. I need the numbers from the bottom of the frame. I had some blocks cut but gave them away. I am not near a coach to measure the difference between the holes in the frame and the bottom of the frame.
Ken B.
|
OK, I found the numbers but I do not believe them. I'll need to measure them again. The numbers I have are 8-7/16 vs.11-11/16 to the hole for the rear and 11-1/8 vs. 13-1/8 to the hole for the front. I do not understand why there is a 1/4 inch difference between the front and the rear. Oh well, I'll measure them again when we get a coach on the pit in Hamilton.
Thanks
Ken B.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
|
|
|
| Re: [GMCnet] Hamilton (Ohio) Work Rally [message #85091 is a reply to message #85087] |
Tue, 18 May 2010 10:30 |
Ken Burton
Messages: 10030
Registered: January 2004
Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
| Ken Coit wrote on Tue, 18 May 2010 09:51 |
Ken,
I just went out and looked to see if I could understand what y'all are
talking about. I found the slots, they are 2-1/2 inches above the bottom of
the frame in front and back. However, there is no convenient spot to put a
block under the slot in front. My guess is that you place the block at a
convenient spot a bit aft where there is an additional thickness of frame
which gives you the 1/4" difference.
I can send a picture if you'd like.
Ken
Ken Coit, ND7N
Raleigh, NC
Parfait Royale
1978 Royale Rear Bath, 403, 3.07
|
Now I'm really confused over 1/4 inch.
The book says:
front 13-1/8" to the top of the holes
rear 11-11/16" to the top of the holes
The wood block measurements I have written down are:
front 10-1/8"
rear 8-7/16"
This means the difference is:
front 3"
rear 3 1/4"
After I wrote the numbers down in this note and read your posting about the double thickness of the frame where you would use the block, it now makes sense.
I'll go cut some new blocks.
I do not need the pictures, but some others here might like to see what we are talking about.
Thanks.
Ken B.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
|
| Re: [GMCnet] Hamilton (Ohio) Work Rally [message #85093 is a reply to message #85091] |
Tue, 18 May 2010 10:46 |
|
|
Sounds like a good idea - link us to the mother ship via photos.
Byron Songer
1978 Royale by Coachmen
Louisville, KY
Personal - http://web.me.com/bnsonger
Eastern States - http://www.gmceast.com
Ken Burton wrote:
>
>
> Ken Coit wrote on Tue, 18 May 2010 09:51
>> Ken,
>>
>> I just went out and looked to see if I could understand what y'all are
>> talking about. I found the slots, they are 2-1/2 inches above the bottom of
>> the frame in front and back. However, there is no convenient spot to put a
>> block under the slot in front. My guess is that you place the block at a
>> convenient spot a bit aft where there is an additional thickness of frame
>> which gives you the 1/4" difference.
>>
>> I can send a picture if you'd like.
>>
>> Ken
>>
>> Ken Coit, ND7N
>> Raleigh, NC
>> Parfait Royale
>> 1978 Royale Rear Bath, 403, 3.07
>
> Now I'm really confused over 1/4 inch.
>
> The book says:
> front 13-1/8" to the top of the holes
> rear 11-11/16" to the top of the holes
>
> The wood block measurements I have written down are:
> front 10-1/8"
> rear 8-7/16"
>
> This means the difference is:
> front 3"
> rear 3 1/4"
>
> After I wrote the numbers down in this note and read your posting about the
> double thickness of the frame where you would use the block, it now makes
> sense.
>
> I'll go cut some new blocks.
>
> I do not need the pictures, but some others here might like to see what we are
> talking about.
>
> Thanks.
>
> Ken B.
>
>
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
--
Byron Songer
Full-timing to enjoy the USA
Former owner but still an admirer
GMC paint schemes at -
http://www.songerconsulting.net
|
|
|
|
| Re: [GMCnet] Hamilton (Ohio) Work Rally [message #85137 is a reply to message #84931] |
Tue, 18 May 2010 16:21 |
Jim Galbavy
Messages: 1443
Registered: August 2007
Karma: 7
|
Senior Member |
|
|
Sandra,
We "offically" will be a the Hagarstown, MD. Koa (Friday thru Sunday) but some of us are going up early on Thursday.
We have a great relationship with the owners and they really make sure we have a good time.
It might be quickest to make your reservation thru the campground and ask them if they can get you in close to us CRABS. We'd love to meet you.
jim galbavy
'73 X-CL (ANNIE)
Chesterfield, Va
804 748 9756
[Updated on: Tue, 18 May 2010 16:22] Report message to a moderator |
|
|
|
| Re: [GMCnet] Hamilton (Ohio) Work Rally [message #85170 is a reply to message #85137] |
Tue, 18 May 2010 20:36 |
Sandra Price
Messages: 709
Registered: May 2006
Karma: 1
|
Senior Member |
|
|
Thanks, Jim. We'll check our map and see if we are anywhere near
Hagarstown. Right now we're planning to go to Point Lookout State Park on
Friday; however, we could change our plans. If we find that we can do that,
we'll let you know.
Sandra and Bob Price (at Smallwood SP, MD)
On Tue, May 18, 2010 at 4:21 PM, Jim Galbavy <j.galbavy@att.net> wrote:
>
>
> Sandra,
>
> We "offically" will be a the Hagarstown, MD. Koa (Friday thru Sunday) but
> some of us are going up early on Thursday.
> We have a great relationship with the owners and they really make sure we
> have a good time.
>
> It might be quickest to make your reservation thru the campground and ask
> them if they can get you in close to us CRABS. We'd love to meet you.
>
> jim galbavy
> '73 X-CL (ANNIE)
> Chesterfield, Va
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
IN GOD WE TRUST!
Sandra and Bob in the 51st Year of our State of Marriage
“Life’s a Trip” in “The Roadhouse”
’73 Painted Desert
Huntsville, TX
Finally, all of you, live in harmony with one another, be sympathetic, love
as brothers, be compassionate and humble. Do not repay evil with evil or
insult with insult, but with blessing, because to this you were called so
that you may inherit a blessing. --1 Peter 3:8-9
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: [GMCnet] Hamilton (Ohio) Work Rally [message #85173 is a reply to message #85137] |
Tue, 18 May 2010 21:04 |
Sandra Price
Messages: 709
Registered: May 2006
Karma: 1
|
Senior Member |
|
|
Jim, we checked and are only about 100 miles away. What KOA will the rally
be held? Let me know and we'll try to come up on Friday.
Thanks in advance.
Sandra and Bob Price
On Tue, May 18, 2010 at 4:21 PM, Jim Galbavy <j.galbavy@att.net> wrote:
>
>
> Sandra,
>
> We "offically" will be a the Hagarstown, MD. Koa (Friday thru Sunday) but
> some of us are going up early on Thursday.
> We have a great relationship with the owners and they really make sure we
> have a good time.
>
> It might be quickest to make your reservation thru the campground and ask
> them if they can get you in close to us CRABS. We'd love to meet you.
>
> jim galbavy
> '73 X-CL (ANNIE)
> Chesterfield, Va
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
IN GOD WE TRUST!
Sandra and Bob in the 51st Year of our State of Marriage
“Life’s a Trip” in “The Roadhouse”
’73 Painted Desert
Huntsville, TX
Finally, all of you, live in harmony with one another, be sympathetic, love
as brothers, be compassionate and humble. Do not repay evil with evil or
insult with insult, but with blessing, because to this you were called so
that you may inherit a blessing. --1 Peter 3:8-9
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
|
|
| Re: [GMCnet] Hamilton (Ohio) Work Rally [message #85284 is a reply to message #85188] |
Wed, 19 May 2010 14:38 |
Sandra Price
Messages: 709
Registered: May 2006
Karma: 1
|
Senior Member |
|
|
We'll be there, Jim. I spoke with Ellie Brennan and LaJo Stiteler this
aftenoon and made our reservations. See you Friday afternoon.
Sandra
On Tue, May 18, 2010 at 10:50 PM, Jim Galbavy <j.galbavy@att.net> wrote:
>
>
> Sandra,
>
> It is:
>
> hagerstown KOA
> 11759 Snug Harbor Lane
> Williamsport, MD 21795
>
> 800 562 7607
>
>
> jim galbavy
> '73 X-CL (ANNIE)
> Chesterfield, Va
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
IN GOD WE TRUST!
Sandra and Bob in the 51st Year of our State of Marriage
“Life’s a Trip” in “The Roadhouse”
’73 Painted Desert
Huntsville, TX
Finally, all of you, live in harmony with one another, be sympathetic, love
as brothers, be compassionate and humble. Do not repay evil with evil or
insult with insult, but with blessing, because to this you were called so
that you may inherit a blessing. --1 Peter 3:8-9
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: [GMCnet] Hamilton (Ohio) Work Rally [message #85326 is a reply to message #85284] |
Wed, 19 May 2010 21:20 |
Ken Burton
Messages: 10030
Registered: January 2004
Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
I did not make it there today. I'll throw some clothes in the truck and head that way in the morning. It is about a 5 hour drive plus an hour time change.
Ken B.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
|
|
|
Goto Forum:
Current Time: Sat Nov 16 22:37:43 CST 2024
Total time taken to generate the page: 0.01843 seconds
|
GMCforum
Search
Help
Register
Login
Home
