GMCforum: GMCnet » Machining Brake Drums

Home » Public Forums » GMCnet » Machining Brake Drums (Machining Brake Drums)

Show: Today's Messages :: Polls :: Message Navigator

Re: [GMCnet] Machining Brake Drums [message #361743 is a reply to message #361740]

Wed, 13 January 2021 19:45

Bruce Hart

Messages: 1500
Registered: October 2011
Location: La Grange, Wyoming

Karma:

Senior Member

I found the spec on the inside of the drum

On Wed, Jan 13, 2021 at 5:59 PM John R. Lebetski via Gmclist <
gmclist@list.gmcnet.org> wrote:

> Yes all drums have the max allowable internal diameter stamped usually on
> the edge. Keep in mind as you approach that size, they will fade sooner
> (less mass) and warp easier if you drive aggressively.
> --
> John Lebetski
> Woodstock, IL
> 77 Eleganza II
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>

--
Bruce Hart
1976 Palm Beach
Milliken, Co
GMC=Got More Class
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org

Bruce Hart 1976 Palm Beach 1977 28' Kingsley La Grange, Wyoming

Report message to a moderator

[Message index]

		Machining Brake Drums By: Ken M on Wed, 13 January 2021 17:55
		Re: [GMCnet] Machining Brake Drums By: Bruce Hart on Wed, 13 January 2021 18:01
		Re: Machining Brake Drums By: JohnL455 on Wed, 13 January 2021 18:59
		Re: [GMCnet] Machining Brake Drums By: Bruce Hart on Wed, 13 January 2021 19:45
		Re: [GMCnet] Machining Brake Drums By: Ken Henderson on Wed, 13 January 2021 23:33
		Re: Machining Brake Drums By: jhbridges on Thu, 14 January 2021 16:54
		Re: [GMCnet] Machining Brake Drums By: Rob on Thu, 14 January 2021 17:07
		Re: [GMCnet] Machining Brake Drums By: James Hupy on Thu, 14 January 2021 19:01
		Re: Machining Brake Drums By: jhbridges on Fri, 15 January 2021 07:51
		Re: Machining Brake Drums By: TR 1 on Fri, 22 January 2021 08:48
		Re: Machining Brake Drums By: Ken M on Fri, 15 January 2021 19:48
		Re: Machining Brake Drums By: Rick Staples on Fri, 15 January 2021 20:45
		Re: Machining Brake Drums By: USAussie on Tue, 19 January 2021 07:33
		Re: Machining Brake Drums By: uprooted on Tue, 19 January 2021 11:25
		Re: Machining Brake Drums By: jhbridges on Fri, 22 January 2021 10:13

Previous Topic:	Faucet rebuild kits?
Next Topic:	[GMCnet] Alternator Question (just curious)

Goto Forum:

-=] Back to Top [=-

Current Time: Fri Jun 28 22:13:55 CDT 2024

Total time taken to generate the page: 0.00594 seconds