GMCforum: GMCnet » How to measure for accurate hole drilling?

Home » Public Forums » GMCnet » How to measure for accurate hole drilling?

Show: Today's Messages :: Polls :: Message Navigator

Re: [GMCnet] How to measure for accurate hole drilling? [message #317490 is a reply to message #317463]

Sat, 13 May 2017 07:59

Matt Colie

Messages: 8547
Registered: March 2007
Location: S.E. Michigan

Karma:

Senior Member

hal kading wrote on Fri, 12 May 2017 15:42

How about these aircraft hole finders?

https://www.browntool.com/Default.aspx?tabid=344&CategoryID=77&Level=a

Hal Kading 78 Buskirk Las Cruces NM

Those are neat and I have used them laying aluminum patches on hulls, but they really on work well on joining flat sheets. Our (or at least my) door(s) have a lip that will preclude getting the centering pin into the hole.

Matt

Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit

Report message to a moderator

[Message index]

		How to measure for accurate hole drilling? By: Michael Bozardt on Sun, 07 May 2017 17:15
		Re: [GMCnet] How to measure for accurate hole drilling? By: Ken Henderson on Sun, 07 May 2017 18:50
		Re: [GMCnet] How to measure for accurate hole drilling? By: Michael Bozardt on Sun, 07 May 2017 23:31
		Re: How to measure for accurate hole drilling? By: 77Royale on Mon, 08 May 2017 07:08
		Re: How to measure for accurate hole drilling? By: Ken Burton on Mon, 08 May 2017 09:31
		Re: How to measure for accurate hole drilling? By: 77Royale on Mon, 08 May 2017 10:20
		Re: [GMCnet] How to measure for accurate hole drilling? By: James Hupy on Mon, 08 May 2017 10:26
		Re: [GMCnet] How to measure for accurate hole drilling? By: Jp Benson on Mon, 08 May 2017 13:47
		Re: [GMCnet] How to measure for accurate hole drilling? By: Ken Burton on Mon, 08 May 2017 15:51
		Re: [GMCnet] How to measure for accurate hole drilling? By: Jp Benson on Mon, 08 May 2017 20:34
		Re: How to measure for accurate hole drilling? By: skip2 on Mon, 08 May 2017 15:52
		Re: How to measure for accurate hole drilling? By: RoadWarrior on Mon, 08 May 2017 16:25
		Re: How to measure for accurate hole drilling? By: Michael Bozardt on Wed, 10 May 2017 09:31
		Re: [GMCnet] How to measure for accurate hole drilling? By: sgltrac on Wed, 10 May 2017 09:41
		Re: How to measure for accurate hole drilling? By: Phantom2 on Mon, 08 May 2017 23:56
		Re: How to measure for accurate hole drilling? By: Matt Colie on Tue, 09 May 2017 07:59
		Re: [GMCnet] How to measure for accurate hole drilling? By: Mike Kelley on Tue, 09 May 2017 08:34
		Re: [GMCnet] How to measure for accurate hole drilling? By: Jp Benson on Tue, 09 May 2017 08:51
		Re: [GMCnet] How to measure for accurate hole drilling? By: Michael Bozardt on Wed, 10 May 2017 09:21
		Re: [GMCnet] How to measure for accurate hole drilling? By: Jp Benson on Wed, 10 May 2017 20:39
		Re: [GMCnet] How to measure for accurate hole drilling? By: Michael Bozardt on Fri, 12 May 2017 10:07
		Re: [GMCnet] How to measure for accurate hole drilling? By: hal kading on Fri, 12 May 2017 14:42
		Re: [GMCnet] How to measure for accurate hole drilling? By: sgltrac on Fri, 12 May 2017 19:22
		Re: [GMCnet] How to measure for accurate hole drilling? By: C Boyd on Fri, 12 May 2017 20:33
		Re: [GMCnet] How to measure for accurate hole drilling? By: Matt Colie on Sat, 13 May 2017 07:59
		Re: [GMCnet] How to measure for accurate hole drilling? By: GMC Cruse on Fri, 12 May 2017 22:58
		Re: [GMCnet] How to measure for accurate hole drilling? By: GMC Cruse on Sat, 13 May 2017 10:32
		Re: How to measure for accurate hole drilling? By: Michael Bozardt on Mon, 29 May 2017 11:26
		Re: [GMCnet] How to measure for accurate hole drilling? By: James Hupy on Mon, 29 May 2017 11:54

Previous Topic:	LPG Regulator
Next Topic:	Finally mounted my Digipanel oil pressure sensor

Goto Forum:

-=] Back to Top [=-

Current Time: Sun Jun 30 09:56:03 CDT 2024

Total time taken to generate the page: 0.01021 seconds