GMCforum: GMCnet » How to measure for accurate hole drilling?

Home » Public Forums » GMCnet » How to measure for accurate hole drilling?

Show: Today's Messages :: Polls :: Message Navigator

Re: How to measure for accurate hole drilling? [message #317239 is a reply to message #317163]

Mon, 08 May 2017 23:56

Phantom2

Messages: 94
Registered: September 2012
Location: Springfield, IL

Karma:

Member

Here's an idea. buy a set of tweezers from Harbor Freight. https://www.harborfreight.com/6-pc-fine-point-tweezer-set-93598.html $6.00

find one that will fit in the screw hole & bend one side of the pair to 90 Degrees outward, cut the other one so it is just short of the bend. Put the bent end in the screw hole, squeeze the pair together & mark at the end of the top arm.

Larry Hopkins 75 Avion Springfield, IL

Report message to a moderator

[Message index]

		How to measure for accurate hole drilling? By: Michael Bozardt on Sun, 07 May 2017 17:15
		Re: [GMCnet] How to measure for accurate hole drilling? By: Ken Henderson on Sun, 07 May 2017 18:50
		Re: [GMCnet] How to measure for accurate hole drilling? By: Michael Bozardt on Sun, 07 May 2017 23:31
		Re: How to measure for accurate hole drilling? By: 77Royale on Mon, 08 May 2017 07:08
		Re: How to measure for accurate hole drilling? By: Ken Burton on Mon, 08 May 2017 09:31
		Re: How to measure for accurate hole drilling? By: 77Royale on Mon, 08 May 2017 10:20
		Re: [GMCnet] How to measure for accurate hole drilling? By: James Hupy on Mon, 08 May 2017 10:26
		Re: [GMCnet] How to measure for accurate hole drilling? By: Jp Benson on Mon, 08 May 2017 13:47
		Re: [GMCnet] How to measure for accurate hole drilling? By: Ken Burton on Mon, 08 May 2017 15:51
		Re: [GMCnet] How to measure for accurate hole drilling? By: Jp Benson on Mon, 08 May 2017 20:34
		Re: How to measure for accurate hole drilling? By: skip2 on Mon, 08 May 2017 15:52
		Re: How to measure for accurate hole drilling? By: RoadWarrior on Mon, 08 May 2017 16:25
		Re: How to measure for accurate hole drilling? By: Michael Bozardt on Wed, 10 May 2017 09:31
		Re: [GMCnet] How to measure for accurate hole drilling? By: sgltrac on Wed, 10 May 2017 09:41
		Re: How to measure for accurate hole drilling? By: Phantom2 on Mon, 08 May 2017 23:56
		Re: How to measure for accurate hole drilling? By: Matt Colie on Tue, 09 May 2017 07:59
		Re: [GMCnet] How to measure for accurate hole drilling? By: Mike Kelley on Tue, 09 May 2017 08:34
		Re: [GMCnet] How to measure for accurate hole drilling? By: Jp Benson on Tue, 09 May 2017 08:51
		Re: [GMCnet] How to measure for accurate hole drilling? By: Michael Bozardt on Wed, 10 May 2017 09:21
		Re: [GMCnet] How to measure for accurate hole drilling? By: Jp Benson on Wed, 10 May 2017 20:39
		Re: [GMCnet] How to measure for accurate hole drilling? By: Michael Bozardt on Fri, 12 May 2017 10:07
		Re: [GMCnet] How to measure for accurate hole drilling? By: hal kading on Fri, 12 May 2017 14:42
		Re: [GMCnet] How to measure for accurate hole drilling? By: sgltrac on Fri, 12 May 2017 19:22
		Re: [GMCnet] How to measure for accurate hole drilling? By: C Boyd on Fri, 12 May 2017 20:33
		Re: [GMCnet] How to measure for accurate hole drilling? By: Matt Colie on Sat, 13 May 2017 07:59
		Re: [GMCnet] How to measure for accurate hole drilling? By: GMC Cruse on Fri, 12 May 2017 22:58
		Re: [GMCnet] How to measure for accurate hole drilling? By: GMC Cruse on Sat, 13 May 2017 10:32
		Re: How to measure for accurate hole drilling? By: Michael Bozardt on Mon, 29 May 2017 11:26
		Re: [GMCnet] How to measure for accurate hole drilling? By: James Hupy on Mon, 29 May 2017 11:54

Previous Topic:	LPG Regulator
Next Topic:	Finally mounted my Digipanel oil pressure sensor

Goto Forum:

-=] Back to Top [=-

Current Time: Sun Jun 30 10:45:23 CDT 2024

Total time taken to generate the page: 0.01166 seconds