Home » Public Forums » GMCnet » [GMCnet] Modifying Cockpit Step
Re: [GMCnet] Modifying Cockpit Step [message #268330 is a reply to message #268328] |
Sat, 27 December 2014 00:02 |
Ken Henderson
Messages: 8726 Registered: March 2004 Location: Americus, GA
Karma:
|
Senior Member |
|
|
Bill,
Yes, I'm afraid this discussion began under another topic. What we're
trying to deterrmine is useable dimensions for drilling access holes
through the lower cockput step riser behind each of the 3 bolts which
attach the rear transmission mount (the "sheet metal" affair) to the bell
housing. For some of us, installing those bolts is a real PITA (sometimes
takes me as long as the rest of the transmission installation). For ANYONE
who modifies the step to each side of the chain housing, so that there's no
access from the sides, it will be might-nigh impossible.
With the plywood removed from the step, you can probably measure where
those riser holes should be located, and hopefully record those dimensions
in reference to some fixed, readily determined location, regardless of the
state of carpet and cabinets in the area. I suspect it will be necessary
to measure the lateral center of the engine hatch and extend a line down
from there to the lower step riser. One could then measure laterally from
that line and vertically from the top surface of the lower step and be
pretty darned close -- certainly close enough for a 1-1/2" hole to allow a
9/16" socket and extension to reach each bolt heads.
Ken H.
On Sat, Dec 27, 2014 at 12:12 AM, Bill wrote:
> I some of this thread somewhere else?
> I dont understa d what hes looking for however I dont have any plywood
> On my engine cover and step on my 77.
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
|
|
[GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
By: USAussie on Fri, 26 December 2014 21:24
|
|
|
Re: [GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
By: USAussie on Sat, 27 December 2014 06:28
|
|
|
Re: [GMCnet] Modifying Cockpit Step
By: Ray R. on Sat, 27 December 2014 08:00
|
|
|
Re: [GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
By: Ray R. on Sat, 27 December 2014 20:09
|
|
|
Re: [GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
By: Ray R. on Sat, 27 December 2014 20:40
|
|
|
Re: [GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
By: USAussie on Sun, 28 December 2014 00:46
|
|
|
Re: [GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
By: USAussie on Sun, 28 December 2014 07:21
|
|
|
Re: [GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
By: USAussie on Sat, 27 December 2014 22:52
|
|
|
[GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
By: USAussie on Sat, 27 December 2014 22:48
|
|
|
Re: [GMCnet] Modifying Cockpit Step
By: jhb1 on Sun, 28 December 2014 08:49
|
|
|
Re: [GMCnet] Modifying Cockpit Step
|
|
|
Re: [GMCnet] Modifying Cockpit Step
By: Ray R. on Sun, 28 December 2014 22:43
|
|
|
Re: [GMCnet] Modifying Cockpit Step
|
Goto Forum:
Current Time: Tue Sep 24 14:10:37 CDT 2024
Total time taken to generate the page: 0.00928 seconds
|