GMCforum
For enthusiast of the Classic GMC Motorhome built from 1973 to 1978. A web-based mirror of the GMCnet mailing list.
Home » Public Forums » GMCnet » Black List call
Re: [GMCnet] Black List call [message #261576 is a reply to message #261574] Thu, 11 September 2014 09:41 Go to previous messageGo to previous message
dwayne jacobson[1] is currently offline  dwayne jacobson[1]   United States
Messages: 345
Registered: July 2009
Karma:
Senior Member
what is the torque for these?



On Thu, Sep 11, 2014 at 7:35 AM, James Hupy wrote:

> One slight reminder. On some, but not perhaps all, GMC final drive flanges,
> the drivers side requires slightly shorter bolts because of clearance
> issues directly behind the flange. If you use three long bolts from the
> passenger side, BE SURE TO CHECK IF THEY WILL CLEAR THE FINAL DRIVE CASE.
> BAD "STUFF" HAPPENS IF YOU DO NOT.
> Jim Hupy
> Salem, Or.
> 78 GMC Royale 403 (headed for Abbotsford, BC today to pack some front and
> rear wheel bearings for a fellow
> gmcer, Then will turn south to the USA and hook up with Todd Sullivan and
> drop off an engine gantry. Wow, busy time for us.
>
> On Thu, Sep 11, 2014 at 9:41 AM, Jim Miller wrote:
>
>> We are talking about the bolts that attach the inboard CV joints to the
>> final drive's output flanges; these are not the bolts that you are
>> referring to.
>>
>> Torque specs for important fasteners are listed in the service manual. I
>> do not trust my memory so I check the manual when in doubt.
>>
>> --Jim
>>
>> On Sep 11, 2014, at 9:19 AM, Mickey Szilagyi wrote:
>>
>>> We just had the oil changed in our new 3.70 final drive after about
> 1000
>> miles of break-in. We had the pan removed so they could inspect the
> inside
>>> and they put on a new gasket which I think we got with the FD. Are
>> these the bolts you are talking about, that hold the pan on? Thinking
>> about this
>>> I don't think it's them but the bolts that actually hold the FD in
>> place. What torque should be used to hold these bolts in place?
>>>
>>> Thanks.
>>> --
>>> Mickey
>>> 1977 Kingsley, 403, Lansing, MI
>>> _______________________________________________
>>> GMCnet mailing list
>>> Unsubscribe or Change List Options:
>>> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>>>
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>



--
Dwayne Jacobson
White Rock BC
Cell: 604-644-8090
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Report message to a moderator

[Message index]
 
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Previous Topic: [GMCnet] GMC MM '96 January, GMC II and so on
Next Topic: Non GMC, US embassy in Oslo Norway testing out Norwegian Xmas food
Goto Forum:
  


Current Time: Sun Oct 06 12:20:10 CDT 2024

Total time taken to generate the page: 0.00937 seconds
.:: Contact :: Home ::.

Powered by: FUDforum 3.1.1.
Copyright ©2001-2021 FUDforum Bulletin Board Software