Home » Public Forums » GMCnet » Black List call
Re: [GMCnet] Black List call [message #261574 is a reply to message #261570] |
Thu, 11 September 2014 09:35 |
James Hupy
Messages: 6806 Registered: May 2010
Karma:
|
Senior Member |
|
|
One slight reminder. On some, but not perhaps all, GMC final drive flanges,
the drivers side requires slightly shorter bolts because of clearance
issues directly behind the flange. If you use three long bolts from the
passenger side, BE SURE TO CHECK IF THEY WILL CLEAR THE FINAL DRIVE CASE.
BAD "STUFF" HAPPENS IF YOU DO NOT.
Jim Hupy
Salem, Or.
78 GMC Royale 403 (headed for Abbotsford, BC today to pack some front and
rear wheel bearings for a fellow
gmcer, Then will turn south to the USA and hook up with Todd Sullivan and
drop off an engine gantry. Wow, busy time for us.
On Thu, Sep 11, 2014 at 9:41 AM, Jim Miller wrote:
> We are talking about the bolts that attach the inboard CV joints to the
> final drive's output flanges; these are not the bolts that you are
> referring to.
>
> Torque specs for important fasteners are listed in the service manual. I
> do not trust my memory so I check the manual when in doubt.
>
> --Jim
>
> On Sep 11, 2014, at 9:19 AM, Mickey Szilagyi wrote:
>
>> We just had the oil changed in our new 3.70 final drive after about 1000
> miles of break-in. We had the pan removed so they could inspect the inside
>> and they put on a new gasket which I think we got with the FD. Are
> these the bolts you are talking about, that hold the pan on? Thinking
> about this
>> I don't think it's them but the bolts that actually hold the FD in
> place. What torque should be used to hold these bolts in place?
>>
>> Thanks.
>> --
>> Mickey
>> 1977 Kingsley, 403, Lansing, MI
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
|
Black List call
|
|
|
Re: Black List call
By: WD0AFQ on Thu, 11 September 2014 06:17
|
|
|
Re: Black List call
By: RobG on Thu, 11 September 2014 06:54
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: [GMCnet] Black list call
|
|
|
Re: [GMCnet] Black list call
|
|
|
Re: [GMCnet] Black list call
|
|
|
Re: [GMCnet] Black list call
|
|
|
Re: [GMCnet] Black list call
|
|
|
Re: [GMCnet] Black list call
|
|
|
Re: [GMCnet] Black list call
|
|
|
Re: [GMCnet] Black list call
By: jknezek on Mon, 21 December 2015 10:48
|
|
|
Re: [GMCnet] Black list call
|
|
|
Re: [GMCnet] Black List call
By: USAussie on Thu, 11 September 2014 12:19
|
|
|
Re: Black List call
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: [GMCnet] Black List call
By: KB on Thu, 11 September 2014 14:29
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: [GMCnet] Black List call
By: Keith V on Thu, 11 September 2014 10:28
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: [GMCnet] Black List call
By: Rob on Thu, 11 September 2014 10:23
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: [GMCnet] Black List call
By: WD0AFQ on Thu, 11 September 2014 11:16
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: [GMCnet] Black List call
By: midlf on Thu, 11 September 2014 11:07
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: Black List call
By: Luvn737s on Thu, 11 September 2014 19:24
|
|
|
Re: [GMCnet] Black List call
|
|
|
Re: Black List call
By: appie on Sat, 13 September 2014 14:24
|
|
|
Re: Black List call
|
|
|
Re: Black List call
|
Goto Forum:
Current Time: Sun Oct 06 13:02:18 CDT 2024
Total time taken to generate the page: 0.00868 seconds
|