GMCforum: GMCnet » [GMCnet] Reviving the Cad 500

Home » Public Forums » GMCnet » [GMCnet] Reviving the Cad 500 (

) 1 Vote

Show: Today's Messages :: Polls :: Message Navigator

Re: [GMCnet] Reviving the Cad 500 [message #165416 is a reply to message #162802]

Thu, 05 April 2012 03:47

Richard Brown

Messages: 281
Registered: May 2009

Karma:

Senior Member

The reason I was thinking about breaking it in using an engine dyno is to take the transmission out of the loop temporarily to see if something like the torque converter/transmission could be the reason that the thrust bearing is failing. Using a chassis dyno on the setup that has been used when it last failed would not isolate the components unless you temporarily used a different transmission/converter from a Cadillac conversion that had been used without a thrust bearing failure. If the engine is dyno-ed without that transmission or torque converter and the thrust bearing shows unusual wear again, you have just eliminated the transmission and the torque converter from the possible source of the problem. If the engine passes the pulls without unusual wear, then you can use the chassis dyno with a converter known to have not caused a problem & the old transmission from your coach, then look at the thrust bearing again. If the thrust bearing is still OK,
then the old transmission can't be the problem & the torque converter must be the problem. At that point, you have empirical evidence that the converter is absolutely the problem. I hope this explains what I'm getting at.Instead of replacing each part permanently with new parts, you are using used parts with a known track record temporarily until you have absolutely found the problem, then you only need to buy the one part that you now know is at fault. Costs a lot less than buying a new converter when it's the transmission at fault or the other way around. I hope this clears up my thought process on this.

Richard & Carol Brown

1974 Eleganza SE

"DILLIGAF"

Lindale, Tx. 75771

903-881-0192
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Richard & Carol Brown 1974 Eleganza SE 1174 Hickory Hills Dr. Murchison, TX. 75778

Report message to a moderator

[Message index]

		[GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 12 March 2012 21:11
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Mon, 12 March 2012 21:51
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Tue, 13 March 2012 07:44
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Mon, 12 March 2012 22:05
		Re: [GMCnet] Reviving the Cad 500 By: sgltrac on Mon, 12 March 2012 23:42
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Mon, 12 March 2012 23:51
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Tue, 13 March 2012 06:55
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 13 March 2012 07:08
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Tue, 13 March 2012 08:02
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Tue, 13 March 2012 09:23
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 13 March 2012 12:05
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Tue, 13 March 2012 12:58
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 13 March 2012 18:15
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Tue, 13 March 2012 18:58
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Tue, 13 March 2012 19:14
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 13 March 2012 19:34
		Re: [GMCnet] Reviving the Cad 500 By: jimk on Wed, 14 March 2012 01:23
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Wed, 14 March 2012 07:28
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Wed, 14 March 2012 21:29
		Re: [GMCnet] Reviving the Cad 500 By: jimk on Thu, 15 March 2012 01:22
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Thu, 15 March 2012 08:43
		Re: [GMCnet] Reviving the Cad 500 By: k2gkk on Thu, 15 March 2012 11:53
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 15 March 2012 21:15
		Re: [GMCnet] Reviving the Cad 500 By: Steve L. Clevenger on Fri, 16 March 2012 00:15
		Re: [GMCnet] Reviving the Cad 500 By: jimk on Fri, 16 March 2012 01:30
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Fri, 16 March 2012 10:09
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Fri, 16 March 2012 01:37
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Thu, 15 March 2012 06:04
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Fri, 16 March 2012 07:54
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Fri, 16 March 2012 08:14
		Re: [GMCnet] Reviving the Cad 500 By: Ken Burton on Sat, 17 March 2012 18:46
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Sat, 17 March 2012 19:24
		Re: [GMCnet] Reviving the Cad 500 By: Ken Burton on Sat, 17 March 2012 19:31
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Sun, 18 March 2012 08:55
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sun, 18 March 2012 20:31
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Sun, 18 March 2012 20:51
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Sun, 18 March 2012 21:16
		Re: [GMCnet] Reviving the Cad 500 By: midlf on Sun, 18 March 2012 22:09
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Sun, 18 March 2012 22:04
		Re: [GMCnet] Reviving the Cad 500 By: James Hupy on Sun, 18 March 2012 22:27
		Re: [GMCnet] Reviving the Cad 500 By: Marsh Wilkes on Sun, 18 March 2012 22:18
		Re: [GMCnet] Reviving the Cad 500 By: Ken Burton on Sun, 18 March 2012 23:35
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Mon, 19 March 2012 01:05
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Mon, 19 March 2012 06:54
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Mon, 19 March 2012 06:50
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Mon, 19 March 2012 07:05
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Mon, 19 March 2012 07:22
		Re: [GMCnet] Reviving the Cad 500 By: James Hupy on Mon, 19 March 2012 10:01
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Tue, 20 March 2012 07:16
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 20 March 2012 08:54
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Tue, 20 March 2012 11:38
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 20 March 2012 12:29
		Re: [GMCnet] Reviving the Cad 500 By: GMC Cruse on Sat, 24 March 2012 11:09
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Sat, 24 March 2012 15:32
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 24 March 2012 21:09
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Sat, 24 March 2012 22:45
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Sun, 25 March 2012 07:00
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 24 March 2012 20:19
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Mon, 19 March 2012 08:02
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Mon, 19 March 2012 09:56
		Re: [GMCnet] Reviving the Cad 500 By: Carl S. on Mon, 19 March 2012 13:08
		Re: [GMCnet] Reviving the Cad 500 By: George Beckman on Sat, 24 March 2012 18:05
		Re: [GMCnet] Reviving the Cad 500 By: Dolph Santorine on Sat, 24 March 2012 18:25
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 24 March 2012 21:21
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 24 March 2012 21:17
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Mon, 26 March 2012 20:55
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Tue, 27 March 2012 07:37
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 27 March 2012 14:12
		Re: [GMCnet] Reviving the Cad 500 By: Mr ERFisher on Tue, 27 March 2012 14:14
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 27 March 2012 14:21
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Tue, 27 March 2012 19:34
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 27 March 2012 21:20
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Wed, 28 March 2012 07:48
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 29 March 2012 18:05
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Wed, 28 March 2012 08:00
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 29 March 2012 18:12
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 31 March 2012 18:06
		Re: [GMCnet] Reviving the Cad 500 By: shawnee on Sat, 31 March 2012 20:11
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 31 March 2012 20:19
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Mon, 02 April 2012 18:28
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Mon, 02 April 2012 18:43
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 02 April 2012 18:54
		Re: [GMCnet] Reviving the Cad 500 By: roy1 on Tue, 03 April 2012 11:15
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 02 April 2012 18:51
		Re: [GMCnet] Reviving the Cad 500 By: Carleton Douglas[1] on Tue, 03 April 2012 08:11
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 03 April 2012 19:18
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Tue, 03 April 2012 16:14
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 03 April 2012 19:36
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Wed, 04 April 2012 16:34
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 17 March 2012 19:40
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Sat, 17 March 2012 20:15
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sun, 18 March 2012 07:49
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Sat, 17 March 2012 20:25
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sun, 18 March 2012 07:44
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Sun, 18 March 2012 03:44
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sun, 18 March 2012 07:42
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Fri, 16 March 2012 20:39
		Re: [GMCnet] Reviving the Cad 500 By: WD0AFQ on Fri, 16 March 2012 22:33
		Re: [GMCnet] Reviving the Cad 500 By: George Beckman on Sat, 17 March 2012 00:41
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 17 March 2012 03:32
		Re: [GMCnet] Reviving the Cad 500 By: James Hupy on Sat, 17 March 2012 10:43
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 17 March 2012 18:25
		Re: [GMCnet] Reviving the Cad 500 By: Ernest Dankert on Sat, 17 March 2012 22:48
		Re: [GMCnet] Reviving the Cad 500 By: roy1 on Mon, 19 March 2012 11:12
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Mon, 19 March 2012 11:30
		Re: [GMCnet] Reviving the Cad 500 By: Ed Jarmul on Mon, 19 March 2012 11:45
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 19 March 2012 14:39
		Re: [GMCnet] Reviving the Cad 500 By: jaholland on Mon, 19 March 2012 18:28
		Re: [GMCnet] Reviving the Cad 500 By: Adrien G. on Mon, 19 March 2012 23:17
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 20 March 2012 08:09
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 28 March 2012 09:46
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Wed, 28 March 2012 13:51
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Wed, 28 March 2012 19:58
		Re: [GMCnet] Reviving the Cad 500 By: klassic kampers on Wed, 28 March 2012 20:19
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 28 March 2012 22:10
		Re: [GMCnet] Reviving the Cad 500 By: rssbob on Wed, 28 March 2012 22:14
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 28 March 2012 22:37
		Re: [GMCnet] Reviving the Cad 500 By: Steve L. Clevenger on Mon, 19 March 2012 23:36
		Re: [GMCnet] Reviving the Cad 500 By: Richard Brown on Wed, 28 March 2012 01:48
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 29 March 2012 18:03
		Re: [GMCnet] Reviving the Cad 500 By: kingd on Sat, 31 March 2012 20:08
		Re: [GMCnet] Reviving the Cad 500 By: Richard Brown on Mon, 02 April 2012 20:21
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 02 April 2012 20:42
		Re: [GMCnet] Reviving the Cad 500 By: JohnL455 on Tue, 03 April 2012 19:17
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Tue, 03 April 2012 22:31
		Re: [GMCnet] Reviving the Cad 500 By: Richard Brown on Tue, 03 April 2012 23:36
		Re: [GMCnet] Reviving the Cad 500 By: JohnL455 on Wed, 04 April 2012 09:24
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 04 April 2012 10:03
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Wed, 04 April 2012 15:38
		Re: [GMCnet] Reviving the Cad 500 By: k2gkk on Wed, 04 April 2012 16:00
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 04 April 2012 17:20
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Wed, 04 April 2012 19:06
		Re: [GMCnet] Reviving the Cad 500 By: JohnL455 on Wed, 04 April 2012 17:28
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Thu, 05 April 2012 09:16
		Re: [GMCnet] Reviving the Cad 500 By: g.winger on Wed, 04 April 2012 19:42
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Wed, 04 April 2012 20:33
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Wed, 04 April 2012 21:20
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Thu, 05 April 2012 05:26
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 08:21
		Re: [GMCnet] Reviving the Cad 500 By: Dan W on Thu, 05 April 2012 09:08
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Thu, 05 April 2012 12:51
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Fri, 06 April 2012 06:52
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Thu, 05 April 2012 07:09
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 08:16
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Fri, 06 April 2012 06:47
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Fri, 06 April 2012 07:45
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Fri, 06 April 2012 07:56
		Re: [GMCnet] Reviving the Cad 500 By: Richard Brown on Thu, 05 April 2012 03:47
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 08:10
		Re: [GMCnet] Reviving the Cad 500 By: g.winger on Thu, 05 April 2012 05:19
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Thu, 05 April 2012 07:45
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 08:27
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Thu, 05 April 2012 21:42
		Re: [GMCnet] Reviving the Cad 500 By: John Heslinga on Thu, 05 April 2012 13:19
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 22:16
		Re: [GMCnet] Reviving the Cad 500 By: Marsh Wilkes on Fri, 06 April 2012 08:06
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Fri, 06 April 2012 08:19
		Re: [GMCnet] Reviving the Cad 500 By: Marsh Wilkes on Fri, 06 April 2012 09:05

Previous Topic:	What's In A Name?
Next Topic:	[GMCnet] Steel 16 Inch Wheels

Goto Forum:

-=] Back to Top [=-

Current Time: Fri Sep 27 13:46:02 CDT 2024

Total time taken to generate the page: 0.01532 seconds