GMCforum: GMCnet » [GMCnet] Reviving the Cad 500

Home » Public Forums » GMCnet » [GMCnet] Reviving the Cad 500 (

) 1 Vote

Show: Today's Messages :: Polls :: Message Navigator

Re: [GMCnet] Reviving the Cad 500 [message #165262 is a reply to message #162802]

Tue, 03 April 2012 23:36

Richard Brown

Messages: 281
Registered: May 2009

Karma:

Senior Member

Does the rebuilder have a dyno or an engine run stand? I'm wondering if, just for process of elimination, you could break in the engine on a dyno, then do a couple of pulls on the engine after break-in. Then drop the pan & check the thrust bearing. If after that the thrust bearing is OK, then that eliminates the engine from the equation as a possible cause. I don't know if there is any such thing as a transmission dyno, but if there were it would help to eliminate it as well. You might even temporarily replace the torque converter with a known good one. What's the old saying that, if you eliminate the impossible, what's left however improbable is the truth. I remember in the Navy that was the usual way to find a problem that defied diagnosis. Replace suspected parts with known good parts until the problem went away. You'll either find the problem or end up with an all-new setup.

Richard & Carol Brown

1974 Eleganza SE

"DILLIGAF"

Lindale, Tx. 75771

903-881-0192
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Richard & Carol Brown 1974 Eleganza SE 1174 Hickory Hills Dr. Murchison, TX. 75778

Report message to a moderator

[Message index]

		[GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 12 March 2012 21:11
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Mon, 12 March 2012 21:51
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Tue, 13 March 2012 07:44
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Mon, 12 March 2012 22:05
		Re: [GMCnet] Reviving the Cad 500 By: sgltrac on Mon, 12 March 2012 23:42
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Mon, 12 March 2012 23:51
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Tue, 13 March 2012 06:55
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 13 March 2012 07:08
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Tue, 13 March 2012 08:02
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Tue, 13 March 2012 09:23
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 13 March 2012 12:05
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Tue, 13 March 2012 12:58
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 13 March 2012 18:15
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Tue, 13 March 2012 18:58
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Tue, 13 March 2012 19:14
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 13 March 2012 19:34
		Re: [GMCnet] Reviving the Cad 500 By: jimk on Wed, 14 March 2012 01:23
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Wed, 14 March 2012 07:28
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Wed, 14 March 2012 21:29
		Re: [GMCnet] Reviving the Cad 500 By: jimk on Thu, 15 March 2012 01:22
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Thu, 15 March 2012 08:43
		Re: [GMCnet] Reviving the Cad 500 By: k2gkk on Thu, 15 March 2012 11:53
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 15 March 2012 21:15
		Re: [GMCnet] Reviving the Cad 500 By: Steve L. Clevenger on Fri, 16 March 2012 00:15
		Re: [GMCnet] Reviving the Cad 500 By: jimk on Fri, 16 March 2012 01:30
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Fri, 16 March 2012 10:09
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Fri, 16 March 2012 01:37
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Thu, 15 March 2012 06:04
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Fri, 16 March 2012 07:54
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Fri, 16 March 2012 08:14
		Re: [GMCnet] Reviving the Cad 500 By: Ken Burton on Sat, 17 March 2012 18:46
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Sat, 17 March 2012 19:24
		Re: [GMCnet] Reviving the Cad 500 By: Ken Burton on Sat, 17 March 2012 19:31
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Sun, 18 March 2012 08:55
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sun, 18 March 2012 20:31
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Sun, 18 March 2012 20:51
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Sun, 18 March 2012 21:16
		Re: [GMCnet] Reviving the Cad 500 By: midlf on Sun, 18 March 2012 22:09
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Sun, 18 March 2012 22:04
		Re: [GMCnet] Reviving the Cad 500 By: James Hupy on Sun, 18 March 2012 22:27
		Re: [GMCnet] Reviving the Cad 500 By: Marsh Wilkes on Sun, 18 March 2012 22:18
		Re: [GMCnet] Reviving the Cad 500 By: Ken Burton on Sun, 18 March 2012 23:35
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Mon, 19 March 2012 01:05
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Mon, 19 March 2012 06:54
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Mon, 19 March 2012 06:50
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Mon, 19 March 2012 07:05
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Mon, 19 March 2012 07:22
		Re: [GMCnet] Reviving the Cad 500 By: James Hupy on Mon, 19 March 2012 10:01
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Tue, 20 March 2012 07:16
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 20 March 2012 08:54
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Tue, 20 March 2012 11:38
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 20 March 2012 12:29
		Re: [GMCnet] Reviving the Cad 500 By: GMC Cruse on Sat, 24 March 2012 11:09
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Sat, 24 March 2012 15:32
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 24 March 2012 21:09
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Sat, 24 March 2012 22:45
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Sun, 25 March 2012 07:00
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 24 March 2012 20:19
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Mon, 19 March 2012 08:02
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Mon, 19 March 2012 09:56
		Re: [GMCnet] Reviving the Cad 500 By: Carl S. on Mon, 19 March 2012 13:08
		Re: [GMCnet] Reviving the Cad 500 By: George Beckman on Sat, 24 March 2012 18:05
		Re: [GMCnet] Reviving the Cad 500 By: Dolph Santorine on Sat, 24 March 2012 18:25
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 24 March 2012 21:21
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 24 March 2012 21:17
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Mon, 26 March 2012 20:55
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Tue, 27 March 2012 07:37
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 27 March 2012 14:12
		Re: [GMCnet] Reviving the Cad 500 By: Mr ERFisher on Tue, 27 March 2012 14:14
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 27 March 2012 14:21
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Tue, 27 March 2012 19:34
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 27 March 2012 21:20
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Wed, 28 March 2012 07:48
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 29 March 2012 18:05
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Wed, 28 March 2012 08:00
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 29 March 2012 18:12
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 31 March 2012 18:06
		Re: [GMCnet] Reviving the Cad 500 By: shawnee on Sat, 31 March 2012 20:11
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 31 March 2012 20:19
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Mon, 02 April 2012 18:28
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Mon, 02 April 2012 18:43
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 02 April 2012 18:54
		Re: [GMCnet] Reviving the Cad 500 By: roy1 on Tue, 03 April 2012 11:15
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 02 April 2012 18:51
		Re: [GMCnet] Reviving the Cad 500 By: Carleton Douglas[1] on Tue, 03 April 2012 08:11
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 03 April 2012 19:18
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Tue, 03 April 2012 16:14
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 03 April 2012 19:36
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Wed, 04 April 2012 16:34
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 17 March 2012 19:40
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Sat, 17 March 2012 20:15
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sun, 18 March 2012 07:49
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Sat, 17 March 2012 20:25
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sun, 18 March 2012 07:44
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Sun, 18 March 2012 03:44
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sun, 18 March 2012 07:42
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Fri, 16 March 2012 20:39
		Re: [GMCnet] Reviving the Cad 500 By: WD0AFQ on Fri, 16 March 2012 22:33
		Re: [GMCnet] Reviving the Cad 500 By: George Beckman on Sat, 17 March 2012 00:41
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 17 March 2012 03:32
		Re: [GMCnet] Reviving the Cad 500 By: James Hupy on Sat, 17 March 2012 10:43
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 17 March 2012 18:25
		Re: [GMCnet] Reviving the Cad 500 By: Ernest Dankert on Sat, 17 March 2012 22:48
		Re: [GMCnet] Reviving the Cad 500 By: roy1 on Mon, 19 March 2012 11:12
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Mon, 19 March 2012 11:30
		Re: [GMCnet] Reviving the Cad 500 By: Ed Jarmul on Mon, 19 March 2012 11:45
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 19 March 2012 14:39
		Re: [GMCnet] Reviving the Cad 500 By: jaholland on Mon, 19 March 2012 18:28
		Re: [GMCnet] Reviving the Cad 500 By: Adrien G. on Mon, 19 March 2012 23:17
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 20 March 2012 08:09
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 28 March 2012 09:46
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Wed, 28 March 2012 13:51
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Wed, 28 March 2012 19:58
		Re: [GMCnet] Reviving the Cad 500 By: klassic kampers on Wed, 28 March 2012 20:19
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 28 March 2012 22:10
		Re: [GMCnet] Reviving the Cad 500 By: rssbob on Wed, 28 March 2012 22:14
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 28 March 2012 22:37
		Re: [GMCnet] Reviving the Cad 500 By: Steve L. Clevenger on Mon, 19 March 2012 23:36
		Re: [GMCnet] Reviving the Cad 500 By: Richard Brown on Wed, 28 March 2012 01:48
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 29 March 2012 18:03
		Re: [GMCnet] Reviving the Cad 500 By: kingd on Sat, 31 March 2012 20:08
		Re: [GMCnet] Reviving the Cad 500 By: Richard Brown on Mon, 02 April 2012 20:21
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 02 April 2012 20:42
		Re: [GMCnet] Reviving the Cad 500 By: JohnL455 on Tue, 03 April 2012 19:17
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Tue, 03 April 2012 22:31
		Re: [GMCnet] Reviving the Cad 500 By: Richard Brown on Tue, 03 April 2012 23:36
		Re: [GMCnet] Reviving the Cad 500 By: JohnL455 on Wed, 04 April 2012 09:24
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 04 April 2012 10:03
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Wed, 04 April 2012 15:38
		Re: [GMCnet] Reviving the Cad 500 By: k2gkk on Wed, 04 April 2012 16:00
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 04 April 2012 17:20
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Wed, 04 April 2012 19:06
		Re: [GMCnet] Reviving the Cad 500 By: JohnL455 on Wed, 04 April 2012 17:28
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Thu, 05 April 2012 09:16
		Re: [GMCnet] Reviving the Cad 500 By: g.winger on Wed, 04 April 2012 19:42
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Wed, 04 April 2012 20:33
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Wed, 04 April 2012 21:20
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Thu, 05 April 2012 05:26
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 08:21
		Re: [GMCnet] Reviving the Cad 500 By: Dan W on Thu, 05 April 2012 09:08
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Thu, 05 April 2012 12:51
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Fri, 06 April 2012 06:52
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Thu, 05 April 2012 07:09
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 08:16
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Fri, 06 April 2012 06:47
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Fri, 06 April 2012 07:45
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Fri, 06 April 2012 07:56
		Re: [GMCnet] Reviving the Cad 500 By: Richard Brown on Thu, 05 April 2012 03:47
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 08:10
		Re: [GMCnet] Reviving the Cad 500 By: g.winger on Thu, 05 April 2012 05:19
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Thu, 05 April 2012 07:45
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 08:27
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Thu, 05 April 2012 21:42
		Re: [GMCnet] Reviving the Cad 500 By: John Heslinga on Thu, 05 April 2012 13:19
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 22:16
		Re: [GMCnet] Reviving the Cad 500 By: Marsh Wilkes on Fri, 06 April 2012 08:06
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Fri, 06 April 2012 08:19
		Re: [GMCnet] Reviving the Cad 500 By: Marsh Wilkes on Fri, 06 April 2012 09:05

Previous Topic:	What's In A Name?
Next Topic:	[GMCnet] Steel 16 Inch Wheels

Goto Forum:

-=] Back to Top [=-

Current Time: Wed Jun 26 07:35:36 CDT 2024

Total time taken to generate the page: 0.03810 seconds