GMCforum: GMCnet » [GMCnet] Reviving the Cad 500

Home » Public Forums » GMCnet » [GMCnet] Reviving the Cad 500 (

) 1 Vote

Show: Today's Messages :: Polls :: Message Navigator

Re: [GMCnet] Reviving the Cad 500 [message #164638 is a reply to message #164431]

Thu, 29 March 2012 18:12

Ken Henderson

Messages: 8726
Registered: March 2004
Location: Americus, GA

Karma:

Senior Member

Johnny,

I understand. I suspect that I'll give up and replace the transmission
before I get that far into an autopsy. Especially since, as I just wrote
to Richard, both the transmission and the engine seem to have had
successful marriages before I hitched them up.

The chain side doesn't seem to me a very likely prospect for causing this
problem -- its sprockets, bearing supports, and bearings pretty well
isolate it from receiving or issuing any damage. However, the input
splined shaft(s) are a different matter. Manny's warned me that he always
chucks them in a lathe to check them for straightness and suggested I do
the same because he DOES find some of them bent. They're also subject to
wear which could cause TC binding.

Back to work tomorrow, probably.

Ken H.

On Wed, Mar 28, 2012 at 9:00 AM, Johnny Bridges wrote:

> The intent is to ensure that the surface which bolts up to both the
> transmission and the engine block is flat - i.e. not warped in such a way
> that the two are being held at an angle. If the trans nput shaft and the
> crankshaft centerline aren't precisely parallel, will not this put a bit of
> an end load on one or both due to a flex in the drive chain? I expect the
> drive system is designed to tolerate substantial side loads on the
> sprockets, but there's not likely to be a lot of provision for end loading,
> since in normal operation there hadn't ought to be any.
> It's a very unlikely scenario admittedly... but you're down to the
> 'unlikelies' at this point, are you not? Easy to check at any rate.
>
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach

Report message to a moderator

[Message index]

		[GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 12 March 2012 21:11
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Mon, 12 March 2012 21:51
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Tue, 13 March 2012 07:44
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Mon, 12 March 2012 22:05
		Re: [GMCnet] Reviving the Cad 500 By: sgltrac on Mon, 12 March 2012 23:42
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Mon, 12 March 2012 23:51
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Tue, 13 March 2012 06:55
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 13 March 2012 07:08
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Tue, 13 March 2012 08:02
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Tue, 13 March 2012 09:23
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 13 March 2012 12:05
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Tue, 13 March 2012 12:58
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 13 March 2012 18:15
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Tue, 13 March 2012 18:58
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Tue, 13 March 2012 19:14
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 13 March 2012 19:34
		Re: [GMCnet] Reviving the Cad 500 By: jimk on Wed, 14 March 2012 01:23
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Wed, 14 March 2012 07:28
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Wed, 14 March 2012 21:29
		Re: [GMCnet] Reviving the Cad 500 By: jimk on Thu, 15 March 2012 01:22
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Thu, 15 March 2012 08:43
		Re: [GMCnet] Reviving the Cad 500 By: k2gkk on Thu, 15 March 2012 11:53
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 15 March 2012 21:15
		Re: [GMCnet] Reviving the Cad 500 By: Steve L. Clevenger on Fri, 16 March 2012 00:15
		Re: [GMCnet] Reviving the Cad 500 By: jimk on Fri, 16 March 2012 01:30
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Fri, 16 March 2012 10:09
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Fri, 16 March 2012 01:37
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Thu, 15 March 2012 06:04
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Fri, 16 March 2012 07:54
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Fri, 16 March 2012 08:14
		Re: [GMCnet] Reviving the Cad 500 By: Ken Burton on Sat, 17 March 2012 18:46
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Sat, 17 March 2012 19:24
		Re: [GMCnet] Reviving the Cad 500 By: Ken Burton on Sat, 17 March 2012 19:31
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Sun, 18 March 2012 08:55
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sun, 18 March 2012 20:31
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Sun, 18 March 2012 20:51
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Sun, 18 March 2012 21:16
		Re: [GMCnet] Reviving the Cad 500 By: midlf on Sun, 18 March 2012 22:09
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Sun, 18 March 2012 22:04
		Re: [GMCnet] Reviving the Cad 500 By: James Hupy on Sun, 18 March 2012 22:27
		Re: [GMCnet] Reviving the Cad 500 By: Marsh Wilkes on Sun, 18 March 2012 22:18
		Re: [GMCnet] Reviving the Cad 500 By: Ken Burton on Sun, 18 March 2012 23:35
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Mon, 19 March 2012 01:05
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Mon, 19 March 2012 06:54
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Mon, 19 March 2012 06:50
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Mon, 19 March 2012 07:05
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Mon, 19 March 2012 07:22
		Re: [GMCnet] Reviving the Cad 500 By: James Hupy on Mon, 19 March 2012 10:01
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Tue, 20 March 2012 07:16
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 20 March 2012 08:54
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Tue, 20 March 2012 11:38
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 20 March 2012 12:29
		Re: [GMCnet] Reviving the Cad 500 By: GMC Cruse on Sat, 24 March 2012 11:09
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Sat, 24 March 2012 15:32
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 24 March 2012 21:09
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Sat, 24 March 2012 22:45
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Sun, 25 March 2012 07:00
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 24 March 2012 20:19
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Mon, 19 March 2012 08:02
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Mon, 19 March 2012 09:56
		Re: [GMCnet] Reviving the Cad 500 By: Carl S. on Mon, 19 March 2012 13:08
		Re: [GMCnet] Reviving the Cad 500 By: George Beckman on Sat, 24 March 2012 18:05
		Re: [GMCnet] Reviving the Cad 500 By: Dolph Santorine on Sat, 24 March 2012 18:25
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 24 March 2012 21:21
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 24 March 2012 21:17
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Mon, 26 March 2012 20:55
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Tue, 27 March 2012 07:37
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 27 March 2012 14:12
		Re: [GMCnet] Reviving the Cad 500 By: Mr ERFisher on Tue, 27 March 2012 14:14
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 27 March 2012 14:21
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Tue, 27 March 2012 19:34
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 27 March 2012 21:20
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Wed, 28 March 2012 07:48
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 29 March 2012 18:05
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Wed, 28 March 2012 08:00
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 29 March 2012 18:12
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 31 March 2012 18:06
		Re: [GMCnet] Reviving the Cad 500 By: shawnee on Sat, 31 March 2012 20:11
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 31 March 2012 20:19
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Mon, 02 April 2012 18:28
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Mon, 02 April 2012 18:43
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 02 April 2012 18:54
		Re: [GMCnet] Reviving the Cad 500 By: roy1 on Tue, 03 April 2012 11:15
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 02 April 2012 18:51
		Re: [GMCnet] Reviving the Cad 500 By: Carleton Douglas[1] on Tue, 03 April 2012 08:11
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 03 April 2012 19:18
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Tue, 03 April 2012 16:14
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 03 April 2012 19:36
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Wed, 04 April 2012 16:34
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 17 March 2012 19:40
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Sat, 17 March 2012 20:15
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sun, 18 March 2012 07:49
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Sat, 17 March 2012 20:25
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sun, 18 March 2012 07:44
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Sun, 18 March 2012 03:44
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sun, 18 March 2012 07:42
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Fri, 16 March 2012 20:39
		Re: [GMCnet] Reviving the Cad 500 By: WD0AFQ on Fri, 16 March 2012 22:33
		Re: [GMCnet] Reviving the Cad 500 By: George Beckman on Sat, 17 March 2012 00:41
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 17 March 2012 03:32
		Re: [GMCnet] Reviving the Cad 500 By: James Hupy on Sat, 17 March 2012 10:43
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 17 March 2012 18:25
		Re: [GMCnet] Reviving the Cad 500 By: Ernest Dankert on Sat, 17 March 2012 22:48
		Re: [GMCnet] Reviving the Cad 500 By: roy1 on Mon, 19 March 2012 11:12
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Mon, 19 March 2012 11:30
		Re: [GMCnet] Reviving the Cad 500 By: Ed Jarmul on Mon, 19 March 2012 11:45
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 19 March 2012 14:39
		Re: [GMCnet] Reviving the Cad 500 By: jaholland on Mon, 19 March 2012 18:28
		Re: [GMCnet] Reviving the Cad 500 By: Adrien G. on Mon, 19 March 2012 23:17
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 20 March 2012 08:09
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 28 March 2012 09:46
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Wed, 28 March 2012 13:51
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Wed, 28 March 2012 19:58
		Re: [GMCnet] Reviving the Cad 500 By: klassic kampers on Wed, 28 March 2012 20:19
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 28 March 2012 22:10
		Re: [GMCnet] Reviving the Cad 500 By: rssbob on Wed, 28 March 2012 22:14
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 28 March 2012 22:37
		Re: [GMCnet] Reviving the Cad 500 By: Steve L. Clevenger on Mon, 19 March 2012 23:36
		Re: [GMCnet] Reviving the Cad 500 By: Richard Brown on Wed, 28 March 2012 01:48
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 29 March 2012 18:03
		Re: [GMCnet] Reviving the Cad 500 By: kingd on Sat, 31 March 2012 20:08
		Re: [GMCnet] Reviving the Cad 500 By: Richard Brown on Mon, 02 April 2012 20:21
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 02 April 2012 20:42
		Re: [GMCnet] Reviving the Cad 500 By: JohnL455 on Tue, 03 April 2012 19:17
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Tue, 03 April 2012 22:31
		Re: [GMCnet] Reviving the Cad 500 By: Richard Brown on Tue, 03 April 2012 23:36
		Re: [GMCnet] Reviving the Cad 500 By: JohnL455 on Wed, 04 April 2012 09:24
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 04 April 2012 10:03
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Wed, 04 April 2012 15:38
		Re: [GMCnet] Reviving the Cad 500 By: k2gkk on Wed, 04 April 2012 16:00
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 04 April 2012 17:20
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Wed, 04 April 2012 19:06
		Re: [GMCnet] Reviving the Cad 500 By: JohnL455 on Wed, 04 April 2012 17:28
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Thu, 05 April 2012 09:16
		Re: [GMCnet] Reviving the Cad 500 By: g.winger on Wed, 04 April 2012 19:42
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Wed, 04 April 2012 20:33
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Wed, 04 April 2012 21:20
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Thu, 05 April 2012 05:26
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 08:21
		Re: [GMCnet] Reviving the Cad 500 By: Dan W on Thu, 05 April 2012 09:08
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Thu, 05 April 2012 12:51
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Fri, 06 April 2012 06:52
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Thu, 05 April 2012 07:09
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 08:16
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Fri, 06 April 2012 06:47
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Fri, 06 April 2012 07:45
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Fri, 06 April 2012 07:56
		Re: [GMCnet] Reviving the Cad 500 By: Richard Brown on Thu, 05 April 2012 03:47
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 08:10
		Re: [GMCnet] Reviving the Cad 500 By: g.winger on Thu, 05 April 2012 05:19
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Thu, 05 April 2012 07:45
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 08:27
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Thu, 05 April 2012 21:42
		Re: [GMCnet] Reviving the Cad 500 By: John Heslinga on Thu, 05 April 2012 13:19
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 22:16
		Re: [GMCnet] Reviving the Cad 500 By: Marsh Wilkes on Fri, 06 April 2012 08:06
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Fri, 06 April 2012 08:19
		Re: [GMCnet] Reviving the Cad 500 By: Marsh Wilkes on Fri, 06 April 2012 09:05

Previous Topic:	What's In A Name?
Next Topic:	[GMCnet] Steel 16 Inch Wheels

Goto Forum:

-=] Back to Top [=-

Current Time: Fri Sep 27 13:44:23 CDT 2024

Total time taken to generate the page: 0.01713 seconds