GMCforum: GMCnet » [GMCnet] Reviving the Cad 500

Home » Public Forums » GMCnet » [GMCnet] Reviving the Cad 500 (

) 1 Vote

Show: Today's Messages :: Polls :: Message Navigator

Re: [GMCnet] Reviving the Cad 500 [message #164071 is a reply to message #163441]

Sat, 24 March 2012 18:05

George Beckman

Messages: 1085
Registered: October 2008
Location: Colfax, CA

Karma:

Senior Member

Ken Henderson wrote on Sun, 18 March 2012 18:31

Today was not a good day.

Baffled, desperate, sad, disgruntled, upset,..., all that stuff, I
started trying to figure what to do. Wound up pulling the starter,
flywheel lower cover, and inspection hole cover. Then disconnected
the torque converter from the new flex plate. Sure 'nuff, the TC
slides fore and aft easily about 1/8" -- just like it should, and did
when installed last Sunday -- it didn't push on the crankshaft. But
something did: With a pry bar I made sure the crank end play (0.008"
when assembled) was all taken up toward the rear to verify the TC free
travel. Then I pried from the rear to the front -- Kerplunk! With a
dial indicator on the flex plate, I found that the crankshaft now has
0.062" end play! Sad

( That's almost half of the 0.125" I accumulated
in the 11,000 miles before the oil analysis identified the problem
before. And this time it took only about 300 miles!!!

I have no idea WHY. Nor WHAT to do. And I don't want to talk about
it or even think about it for a while. Y'All figure it out; I'm gonna
go pout.

Ken,

Terrible news.

The following is probably all wet, but we are grasping at straws here.

I don't know beans about these GMCs compared to some but this has to be a lot of force. Are we sure there is not something amiss with the upper chain/sprocket/bearing/case? I don't even know how that is all held in there, but could something be out of line that is driving the sprocket forward into the TC and then on to the flex plate and crank? I know the TC is supposed to slid on the shaft. I just wonder if the sprocket dropped (pulled toward the driven sprocket) even a tiny amount it would be shoved forward by the uneven chain pressure. The flex plate could be making up for the misalignment.

'74 Eleganza, SE, Howell + EBL
Best Wishes,
George

Report message to a moderator

[Message index]

		[GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 12 March 2012 21:11
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Mon, 12 March 2012 21:51
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Tue, 13 March 2012 07:44
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Mon, 12 March 2012 22:05
		Re: [GMCnet] Reviving the Cad 500 By: sgltrac on Mon, 12 March 2012 23:42
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Mon, 12 March 2012 23:51
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Tue, 13 March 2012 06:55
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 13 March 2012 07:08
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Tue, 13 March 2012 08:02
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Tue, 13 March 2012 09:23
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 13 March 2012 12:05
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Tue, 13 March 2012 12:58
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 13 March 2012 18:15
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Tue, 13 March 2012 18:58
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Tue, 13 March 2012 19:14
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 13 March 2012 19:34
		Re: [GMCnet] Reviving the Cad 500 By: jimk on Wed, 14 March 2012 01:23
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Wed, 14 March 2012 07:28
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Wed, 14 March 2012 21:29
		Re: [GMCnet] Reviving the Cad 500 By: jimk on Thu, 15 March 2012 01:22
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Thu, 15 March 2012 08:43
		Re: [GMCnet] Reviving the Cad 500 By: k2gkk on Thu, 15 March 2012 11:53
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 15 March 2012 21:15
		Re: [GMCnet] Reviving the Cad 500 By: Steve L. Clevenger on Fri, 16 March 2012 00:15
		Re: [GMCnet] Reviving the Cad 500 By: jimk on Fri, 16 March 2012 01:30
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Fri, 16 March 2012 10:09
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Fri, 16 March 2012 01:37
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Thu, 15 March 2012 06:04
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Fri, 16 March 2012 07:54
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Fri, 16 March 2012 08:14
		Re: [GMCnet] Reviving the Cad 500 By: Ken Burton on Sat, 17 March 2012 18:46
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Sat, 17 March 2012 19:24
		Re: [GMCnet] Reviving the Cad 500 By: Ken Burton on Sat, 17 March 2012 19:31
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Sun, 18 March 2012 08:55
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sun, 18 March 2012 20:31
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Sun, 18 March 2012 20:51
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Sun, 18 March 2012 21:16
		Re: [GMCnet] Reviving the Cad 500 By: midlf on Sun, 18 March 2012 22:09
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Sun, 18 March 2012 22:04
		Re: [GMCnet] Reviving the Cad 500 By: James Hupy on Sun, 18 March 2012 22:27
		Re: [GMCnet] Reviving the Cad 500 By: Marsh Wilkes on Sun, 18 March 2012 22:18
		Re: [GMCnet] Reviving the Cad 500 By: Ken Burton on Sun, 18 March 2012 23:35
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Mon, 19 March 2012 01:05
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Mon, 19 March 2012 06:54
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Mon, 19 March 2012 06:50
		Re: [GMCnet] Reviving the Cad 500 By: USAussie on Mon, 19 March 2012 07:05
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Mon, 19 March 2012 07:22
		Re: [GMCnet] Reviving the Cad 500 By: James Hupy on Mon, 19 March 2012 10:01
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Tue, 20 March 2012 07:16
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 20 March 2012 08:54
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Tue, 20 March 2012 11:38
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 20 March 2012 12:29
		Re: [GMCnet] Reviving the Cad 500 By: GMC Cruse on Sat, 24 March 2012 11:09
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Sat, 24 March 2012 15:32
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 24 March 2012 21:09
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Sat, 24 March 2012 22:45
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Sun, 25 March 2012 07:00
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 24 March 2012 20:19
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Mon, 19 March 2012 08:02
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Mon, 19 March 2012 09:56
		Re: [GMCnet] Reviving the Cad 500 By: Carl S. on Mon, 19 March 2012 13:08
		Re: [GMCnet] Reviving the Cad 500 By: George Beckman on Sat, 24 March 2012 18:05
		Re: [GMCnet] Reviving the Cad 500 By: Dolph Santorine on Sat, 24 March 2012 18:25
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 24 March 2012 21:21
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 24 March 2012 21:17
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Mon, 26 March 2012 20:55
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Tue, 27 March 2012 07:37
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 27 March 2012 14:12
		Re: [GMCnet] Reviving the Cad 500 By: Mr ERFisher on Tue, 27 March 2012 14:14
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 27 March 2012 14:21
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Tue, 27 March 2012 19:34
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 27 March 2012 21:20
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Wed, 28 March 2012 07:48
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 29 March 2012 18:05
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Wed, 28 March 2012 08:00
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 29 March 2012 18:12
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 31 March 2012 18:06
		Re: [GMCnet] Reviving the Cad 500 By: shawnee on Sat, 31 March 2012 20:11
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 31 March 2012 20:19
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Mon, 02 April 2012 18:28
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Mon, 02 April 2012 18:43
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 02 April 2012 18:54
		Re: [GMCnet] Reviving the Cad 500 By: roy1 on Tue, 03 April 2012 11:15
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 02 April 2012 18:51
		Re: [GMCnet] Reviving the Cad 500 By: Carleton Douglas[1] on Tue, 03 April 2012 08:11
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 03 April 2012 19:18
		Re: [GMCnet] Reviving the Cad 500 By: Larry on Tue, 03 April 2012 16:14
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 03 April 2012 19:36
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Wed, 04 April 2012 16:34
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 17 March 2012 19:40
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Sat, 17 March 2012 20:15
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sun, 18 March 2012 07:49
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Sat, 17 March 2012 20:25
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sun, 18 March 2012 07:44
		Re: [GMCnet] Reviving the Cad 500 By: ljdavick on Sun, 18 March 2012 03:44
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sun, 18 March 2012 07:42
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Fri, 16 March 2012 20:39
		Re: [GMCnet] Reviving the Cad 500 By: WD0AFQ on Fri, 16 March 2012 22:33
		Re: [GMCnet] Reviving the Cad 500 By: George Beckman on Sat, 17 March 2012 00:41
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 17 March 2012 03:32
		Re: [GMCnet] Reviving the Cad 500 By: James Hupy on Sat, 17 March 2012 10:43
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Sat, 17 March 2012 18:25
		Re: [GMCnet] Reviving the Cad 500 By: Ernest Dankert on Sat, 17 March 2012 22:48
		Re: [GMCnet] Reviving the Cad 500 By: roy1 on Mon, 19 March 2012 11:12
		Re: [GMCnet] Reviving the Cad 500 By: Dennis S on Mon, 19 March 2012 11:30
		Re: [GMCnet] Reviving the Cad 500 By: Ed Jarmul on Mon, 19 March 2012 11:45
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 19 March 2012 14:39
		Re: [GMCnet] Reviving the Cad 500 By: jaholland on Mon, 19 March 2012 18:28
		Re: [GMCnet] Reviving the Cad 500 By: Adrien G. on Mon, 19 March 2012 23:17
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Tue, 20 March 2012 08:09
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 28 March 2012 09:46
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Wed, 28 March 2012 13:51
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Wed, 28 March 2012 19:58
		Re: [GMCnet] Reviving the Cad 500 By: klassic kampers on Wed, 28 March 2012 20:19
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 28 March 2012 22:10
		Re: [GMCnet] Reviving the Cad 500 By: rssbob on Wed, 28 March 2012 22:14
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 28 March 2012 22:37
		Re: [GMCnet] Reviving the Cad 500 By: Steve L. Clevenger on Mon, 19 March 2012 23:36
		Re: [GMCnet] Reviving the Cad 500 By: Richard Brown on Wed, 28 March 2012 01:48
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 29 March 2012 18:03
		Re: [GMCnet] Reviving the Cad 500 By: kingd on Sat, 31 March 2012 20:08
		Re: [GMCnet] Reviving the Cad 500 By: Richard Brown on Mon, 02 April 2012 20:21
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Mon, 02 April 2012 20:42
		Re: [GMCnet] Reviving the Cad 500 By: JohnL455 on Tue, 03 April 2012 19:17
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Tue, 03 April 2012 22:31
		Re: [GMCnet] Reviving the Cad 500 By: Richard Brown on Tue, 03 April 2012 23:36
		Re: [GMCnet] Reviving the Cad 500 By: JohnL455 on Wed, 04 April 2012 09:24
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 04 April 2012 10:03
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Wed, 04 April 2012 15:38
		Re: [GMCnet] Reviving the Cad 500 By: k2gkk on Wed, 04 April 2012 16:00
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Wed, 04 April 2012 17:20
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Wed, 04 April 2012 19:06
		Re: [GMCnet] Reviving the Cad 500 By: JohnL455 on Wed, 04 April 2012 17:28
		Re: [GMCnet] Reviving the Cad 500 By: Matt Colie on Thu, 05 April 2012 09:16
		Re: [GMCnet] Reviving the Cad 500 By: g.winger on Wed, 04 April 2012 19:42
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Wed, 04 April 2012 20:33
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Wed, 04 April 2012 21:20
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Thu, 05 April 2012 05:26
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 08:21
		Re: [GMCnet] Reviving the Cad 500 By: Dan W on Thu, 05 April 2012 09:08
		Re: [GMCnet] Reviving the Cad 500 By: Bob de Kruyff on Thu, 05 April 2012 12:51
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Fri, 06 April 2012 06:52
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Thu, 05 April 2012 07:09
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 08:16
		Re: [GMCnet] Reviving the Cad 500 By: jhbridges on Fri, 06 April 2012 06:47
		Re: [GMCnet] Reviving the Cad 500 By: Steven Ferguson on Fri, 06 April 2012 07:45
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Fri, 06 April 2012 07:56
		Re: [GMCnet] Reviving the Cad 500 By: Richard Brown on Thu, 05 April 2012 03:47
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 08:10
		Re: [GMCnet] Reviving the Cad 500 By: g.winger on Thu, 05 April 2012 05:19
		Re: [GMCnet] Reviving the Cad 500 By: GMC_LES on Thu, 05 April 2012 07:45
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 08:27
		Re: [GMCnet] Reviving the Cad 500 By: Kosier on Thu, 05 April 2012 21:42
		Re: [GMCnet] Reviving the Cad 500 By: John Heslinga on Thu, 05 April 2012 13:19
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Thu, 05 April 2012 22:16
		Re: [GMCnet] Reviving the Cad 500 By: Marsh Wilkes on Fri, 06 April 2012 08:06
		Re: [GMCnet] Reviving the Cad 500 By: Ken Henderson on Fri, 06 April 2012 08:19
		Re: [GMCnet] Reviving the Cad 500 By: Marsh Wilkes on Fri, 06 April 2012 09:05

Previous Topic:	What's In A Name?
Next Topic:	[GMCnet] Steel 16 Inch Wheels

Goto Forum:

-=] Back to Top [=-

Current Time: Fri Sep 27 13:44:23 CDT 2024

Total time taken to generate the page: 0.02281 seconds