GMCforum: GMCnet » toilet flange

Home » Public Forums » GMCnet » toilet flange

Show: Today's Messages :: Polls :: Message Navigator

toilet flange [message #97229]

Wed, 25 August 2010 20:21

Smitty52

Messages: 181
Registered: July 2007

Karma: 0

Senior Member

The toilet flange in our coach has the toilet mounting bolts at 11 and 5 O'clock. To replace the toilet I need a flange that has the mounting bolts at 3 and 9 O'clock. I am putting a new seal kit in the Thetford unit but we would like to find a new flange in the event that the seal kit does not do the job or has a limited life span. The flange in the coach has a broad metal base that the whole toilet sits on, it is not just a ring. I assume it is factory? Suggestions on how to proceed? Just go to Lowes and get a ring and get rid of the metal base plate? Any vendors carry a metal base plate and ring?

Thanks for any ideas.

Wayne and Lisa,
Bolton Landing, NY,
Patriot Guard Rider,
Standing for those who stood for us.

Report message to a moderator

Re: toilet flange [message #97242 is a reply to message #97229]

Wed, 25 August 2010 21:42

Hardie Johnson

Messages: 483
Registered: January 2004
Location: Raleigh NC

Karma: 0

Senior Member

IIR, the flange and the vertical pipe in mine just screwed into the top of the tank. I think what I did was install two bolts in the good holes and use a big stick as a wrench to turn the whole thing out, then made a new piece with like 4" pipe and a plastic flange. I did need a special 1/4" drive deep socket to get the hold down bolts (nuts?) off to remove the toilet.
"its all a blur to me now"

Hardie Johnson "Crashj"
1973 26 foot Glacier, White Thing
Raleigh NC

Report message to a moderator

Re: toilet flange [message #97244 is a reply to message #97229]

Wed, 25 August 2010 21:51

Craig Lechowicz

Messages: 541
Registered: October 2006
Location: Waterford, MI

Karma: 0

Senior Member

Smitty52 wrote on Wed, 25 August 2010 21:21

The toilet flange in our coach has the toilet mounting bolts at 11 and 5 O'clock. To replace the toilet I need a flange that has the mounting bolts at 3 and 9 O'clock. . . .
Thanks for any ideas.

What Hardie said. I just put a new toilet in mine, and I believe the old toilet and flange were original. It was a Thetford AquaMagic III toilet, had a plastic flange, that was threaded to a short length of 3" threaded pipe, that was threaded into the waste tank. The local R/V shop had a new 4" x 3" threaded flange for $8. There were 8 rusted wood screws holding the flange to the floor that located where the toilet bolts were located. I was able to drill the heads off the screws, pull up on the flange to screw it off, then use vise grips to remove what was left of the screws. New stainless screws replaced for that inevitable day when I get to replace the holding tank. No metal anywhere, so I'm thinking you might have had some help from a previous owner?

Craig Lechowicz
'77 Kingsley, Waterford, MI

Report message to a moderator

Re: [GMCnet] toilet flange [message #97248 is a reply to message #97229]

Wed, 25 August 2010 23:00

Mr ERFisher

Messages: 7117
Registered: August 2005

Karma: 2

Senior Member

>
> Thanks for any ideas.
> --
>
this might help - from Kelvin

http://www.gmcmhphotos.com/photos/showgallery.php?cat=4966

gene

> Wayne and Lisa,
> Bolton Landing, NY,
>
> Big Blue Bus AKA Triple B, 78 Royale center kitchen,
>
> Patriot Guard Rider,
> Standing for those who stood for us.
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>

--
Gene Fisher -- 74-23,77PB/ore/ca
�Give a man a fish; you have fed him for today --- give him a URL and
-------
http://gmcmotorhome.info/
Alternator Protection Cable
http://gmcmotorhome.info/APC.html
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Report message to a moderator

Previous Topic:	Wheel Spacer Torque
Next Topic:	[GMCnet] GMC Parts no longer needed

Goto Forum:

-=] Back to Top [=-

Current Time: Sat Feb 01 16:03:02 CST 2025

Total time taken to generate the page: 0.04211 seconds