Tubing fabrication [message #91804] |
Tue, 13 July 2010 13:37 |
petemosss
Messages: 221 Registered: August 2008 Location: Jacksonville, Florida
Karma: 0
|
Senior Member |
|
|
When flaring 37 deg ends on steel tubing one uses steel nuts and sleeves.
When flaring 37 deg ends on copper tubing one uses steel nuts and sleeves.
When flaring 37 deg ends on aluminum tubing can one use steel nuts and sleeves vs the overpriced speedshop aluminum nuts and sleeves?
Pete
74 Canyon Lands 26' "Emery"
|
|
|
Re: Tubing fabrication [message #91822 is a reply to message #91804] |
Tue, 13 July 2010 16:21 |
GeorgeRud
Messages: 1380 Registered: February 2007 Location: Chicago, IL
Karma: 0
|
Senior Member |
|
|
It sounds like the flare is the same, but I wonder if corrosion from dissimilar metals would be a problem. Also, the softer aluminum may deform too much when tightened by the steel nut (?).
George Rudawsky
Chicago, IL
75 Palm Beach
|
|
|
|
Re: [GMCnet] Tubing fabrication [message #91917 is a reply to message #91915] |
Wed, 14 July 2010 07:41 |
Carleton Douglas[1]
Messages: 174 Registered: March 2006
Karma: 0
|
Senior Member |
|
|
Steel brake lines work real well also and I think they are much
cheeper than alum..
On Wed, Jul 14, 2010 at 5:27 AM, Steven Ferguson <botiemad11@gmail.com> wrote:
> George,
> I have had good luck with alum fuel lines with 37 deg flares. The
> soft alum really conforms well to the male surface. Much easier to
> use that SS which tends to gall softer materials.
>
> On Tue, Jul 13, 2010 at 2:21 PM, George Rudawsky <GeorgeRud@aol.com> wrote:
>>
>>
>> It sounds like the flare is the same, but I wonder if corrosion from dissimilar metals would be a problem. Also, the softer aluminum may deform too much when tightened by the steel nut (?).
>> --
>> George Rudawsky
>> Chicago, IL
>> 75 Palm Beach
>> _______________________________________________
>> GMCnet mailing list
>> List Information and Subscription Options:
>> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>>
>
>
>
> --
> Steve Ferguson
> '76 EII
> Sierra Vista, AZ
> Urethane bushing source
> www.bdub.net/ferguson/
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Carleton Douglas
73 custom, by myself
Prescott, AZ
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
Re: [GMCnet] Tubing fabrication [message #91976 is a reply to message #91974] |
Wed, 14 July 2010 17:19 |
gmcrv1
Messages: 839 Registered: August 2007 Location: Memphis
Karma: -1
|
Senior Member |
|
|
Try this.
http://www.fedhillusa.com/
Tom Eckert N2VWN
73 Glacier
Oakland, TN
On Wed, Jul 14, 2010 at 5:13 PM, Steven Ferguson <botiemad11@gmail.com>wrote:
> Carlton,
> I would only use steel for brake lines. The aluminum was for fuel.
> Had a car with a fuel cell and it had 1/2" aluminum fuel lines. Nice
> to work with but again, for brakes I would only use steel.
>
> On Wed, Jul 14, 2010 at 5:41 AM, Carleton Douglas <aecsdouglas@gmail.com>
> wrote:
> > Steel brake lines work real well also and I think they are much
> > cheeper than alum..
> --
> Steve Ferguson
> '76 EII
> Sierra Vista, AZ
> Urethane bushing source
> www.bdub.net/ferguson/
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
Re: Tubing fabrication [message #92014 is a reply to message #91804] |
Thu, 15 July 2010 08:22 |
petemosss
Messages: 221 Registered: August 2008 Location: Jacksonville, Florida
Karma: 0
|
Senior Member |
|
|
Thanks for the input. I'm thinking fuel here and female vs inverted flare. I bought a 20' stick of hydraulic steel tube from my favorite supply house and in just under a few weeks siting outside(protected too) it has rusted both inside and out. I paid $1.13' and the local speed shop has 25' rolls of 3/8" alum for $28. so costs are close. I have all the POR15 tank products but derusting and coating 3/8" pieces of tubing do not sound fun or practical. Supply house does not sell Aluminum tubing and they can't advise. Aluminum nuts and sleeves thru Russell or Aeroquip are astronomical and for weight reasons I think.
Pete
74 Canyon Lands 26' "Emery"
|
|
|